对称刻槽预控破片战斗部壳体爆炸过程质量损失率研究

doi:10.3969/j.issn.1000-1093.2018.02.006

兵工学报 ›› 2018, Vol. 39 ›› Issue (2): 254-260.doi: 10.3969/j.issn.1000-1093.2018.02.006

对称刻槽预控破片战斗部壳体爆炸过程质量损失率研究

张高峰，李向东，周兰伟，马丽英

（南京理工大学智能弹药技术国防重点学科实验室, 江苏南京 210094）

收稿日期:2017-04-14 修回日期:2017-04-14 上线日期:2018-04-04
通讯作者: 李向东（1969—），男，教授，博士生导师 E-mail:lixiangd@mail.njust.edu.cn
作者简介:张高峰（1992—），男，硕士研究生。E-mail:z_gaofeng@163.com

Research on the Explosion Mass Loss Rate of Pre-formed Fragment Warhead Shell with Symmetric Groove

ZHANG Gao-feng, LI Xiang-dong, ZHOU Lan-wei, MA Li-ying

(Ministerial Key Laboratory of ZNDY, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China)

Received:2017-04-14 Revised:2017-04-14 Online:2018-04-04

摘要/Abstract

摘要： 为研究对称刻槽预控破片战斗部壳体爆炸过程质量损失率，在分析轴向刻槽与周向刻槽引起的壳体断裂迹线走向问题基础上，获得了壳体爆炸质量损失来源,提出了壳体爆炸质量损失率计算模型。对典型战斗部壳体爆炸质量损失率进行理论计算，设计了两种模拟战斗部，进行了水井静爆试验。试验结果与理论分析表明：壳体在爆炸过程中，壳体上沿轴向方向刻槽会促使壳体在刻槽根部延伸出两条对称的断裂迹线，壳体上沿周向方向刻槽会促使壳体在刻槽根部仅延伸出一条断裂迹线；壳体上沿轴向刻槽是壳体产生爆炸质量损失的原因，刻槽深度越大，壳体爆炸质量损失率越小；该模型计算结果与试验结果的偏差小于8%.

关键词: 战斗部, 破片, 对称刻槽, 质量损失率, 断裂迹线, 刻槽深度

Abstract: The fracture path of shell caused by the axial groove and circumferential groove is analyzed to study the explosion mass loss rate of pre-formed fragment warhead shell with symmetric groove. The source of explosive mass loss is determined. The explosion mass loss rate of typical warhead shell is calculated in theory. Two kinds of simulated warhead were designed, and the static explosion test was carried out under water. The test results and theoretical analysis show that, in the process of explosion, the axial groove on the shell causes two symmetrical fracture traces from the groove root, the circumferential groove on the shell causes only one fracture trace from the groove root. The explosion mass loss rate of shell is caused by axial groove. The greater the groove depth is, the smaller the mass loss rate of shell explosion is. The difference between theoretically calculated and experimental mass loss rates is less than 8%. Key

Key words: warhead, fragment, symmetricgroove, masslossrate, fracturetrace, groovedepth

中图分类号:

TJ410.3⁺3

张高峰，李向东，周兰伟，马丽英. 对称刻槽预控破片战斗部壳体爆炸过程质量损失率研究[J]. 兵工学报, 2018, 39(2): 254-260.

ZHANG Gao-feng, LI Xiang-dong, ZHOU Lan-wei, MA Li-ying. Research on the Explosion Mass Loss Rate of Pre-formed Fragment Warhead Shell with Symmetric Groove[J]. Acta Armamentarii, 2018, 39(2): 254-260.

参考文献

［1］厉相宝, 杨云川, 倪庆杰. 预控破片形成过程的数值模拟与分析［J］. 沈阳理工大学学报, 2009, 28(1):37-40.
LI Xiang-bao, YANG Yun-chuan, NI Qing-jie. Numerical simulation and analysis of the formation of preformed fragments［J］. Journal of Shenyang Ligong University, 2009, 28(1):37-40. (in Chinese)

［2］ Taylor G I. Fragmentation of tubular bombs［M］.London, UK: Cambridge University Press, 1963: 387-390.
［3］ Reid S R. Metal forming and impact mechanics: William Johnson commemorative volume［M］. London, UK:Pergamon Press, 2016:303-323.
［4］吴成, 倪艳光, 张渝霞. 内刻V形槽半预制破片战斗部壳体的断裂准则［J］. 北京理工大学学报, 2008, 28(7): 569-572.
WU Cheng, NI Yan-guang, ZHANG Yu-xia.Critical fracture criterion on shells of controlled fragmenting warhead with V-notches on their inner surface［J］. Transactions of Beijing Institute of Technology, 2008, 28(7):569-572. (in Chinese)
［5］吴成, 倪艳光, 张渝霞, 等. 不同热处理条件下半预制破片战斗部壳体的金相观察分析［J］.北京理工大学学报, 2008, 28(5): 381-384.
WU Cheng, NI Yan-guang, ZHANG Yu-xia,et al. Metallograpic analysis of semi-preformed fragment warhead steel by different heat treatment［J］. Transactions of Beijing Institute of Technology, 2008, 28(5):381-384.(in Chinese)
［6］ Pearson J. Means for controlled fragmentation: US, US4068590［P］. 1978-1-17.
［7］ Richard M L. Conventional warhead systems physics and engineering design［M］. Reston, VA, US:AIAA,1998:49-73.
［8］刘桂峰, 张庆, 沈晓军, 等. 刻槽参数对破片形成的影响［J］. 弹道学报, 2014, 26(2):63-66.
LIU Gui-feng, ZHANG Qing, SHEN Xiao-jun, et al.Effect of groove parameters on formation of fragments［J］. Journal of Ballistics, 2014, 26(2): 63-66.(in Chinese)
［9］ Pearson J. The shear-control method of warhead fragmentation［C］∥ Proceedings of the 4th International Symposium on Ballistics. Monterey, CA, US: International Ballistics Society ,1978: 17-19.

［10］ Pike A W, Zuo Q H. Geometric design consideration for controlled fragmentation of metallic shells［J］. Finite Elements in Analysis and Design,2014, 91: 59-67.
［11］ Erdogan F, Sih G C. On the crack extension in plates under plane loading and transverse shear［J］. Journal of Basic Engineering, 1963, 85(4): 519-527.
［12］郦正能, 张纪奎. 工程断裂力学［M］. 北京:北京航空航天大学出版社, 2012: 61-73.
LI Zheng-neng, ZHANG Ji-kui. Engineering fracture mechanics［M］. Beijing: Beihang University Press, 2012:61-73.(in Chinese)
［13］ Lloyd R. Conventional warhead systems physics and engineering design［M］. Reston, VA, US:American Institute of Aeronautics and Astronautics Inc, 1998: 49-50.

第39卷第2期
2018 年2月兵工学报ACTA
ARMAMENTARIIVol.39No.2Feb. 2018

[1]	王歌，张春，林智伟，王保华，檀虎，陈晨. 多束定向预制破片弹开舱距离研究[J]. 兵工学报, 2022, 43(S1): 115-120.
[2]	辛大钧，薛琨. 基于人工神经网络的非球形破片阻力系数预测模型[J]. 兵工学报, 2022, 43(5): 1083-1092.
[3]	刘铁磊，徐豫新，王晓锋，张鹏，张健. 钨合金球形破片侵彻低碳钢的弹道极限速度计算模型[J]. 兵工学报, 2022, 43(4): 768-779.
[4]	任思远, 张庆明, 张晓伟, 田志敏. 环形射流和中心爆炸成型弹丸组合战斗部对混凝土墙的破孔特性[J]. 兵工学报, 2021, 42(8): 1569-1579.
[5]	程远胜，谢杰克，李哲，刘均，张攀. 冲击波和破片群联合作用下高强聚乙烯/泡沫铝夹芯复合结构毁伤响应特性[J]. 兵工学报, 2021, 42(8): 1753-1762.
[6]	王孟鑫，陈睿颖，王金相. 破片与冲击波联合作用下多孔泡沫铝夹芯复合材料板的防护性能[J]. 兵工学报, 2021, 42(5): 1041-1052.
[7]	李鑫，王伟力，梁争峰，陈进，陈元建. 复合结构活性破片对双层靶标毁伤效应[J]. 兵工学报, 2021, 42(4): 764-772.
[8]	张浩宇，张树凯，程立，李元，温玉全，张郑伟. 杀伤爆破战斗部起爆方式对地面目标杀伤威力的影响[J]. 兵工学报, 2021, 42(11): 2300-2309.
[9]	彭嘉诚，蒋建伟，李响，李帅孝，陈永恒. 杀伤爆破弹弹体异常淬火时弹底大破片形成机理[J]. 兵工学报, 2021, 42(11): 2333-2343.
[10]	马坤，陈春林，冯娜，尹立新，李名锐，周刚. 柱形93钨弹体超高速撞击薄钢板穿孔及破片群扩展特征[J]. 兵工学报, 2021, 42(11): 2350-2359.
[11]	韩晋阳, 白春华，檀盼龙. 伞降战斗部毁伤试验落点预测方法研究[J]. 兵工学报, 2020, 41(6): 1077-1084.
[12]	程祥利，刘波，赵慧，刘军. 侵彻战斗部-引信系统动力学建模与仿真[J]. 兵工学报, 2020, 41(4): 625-633.
[13]	汪金奎，娄文忠，刘伟桐，苏子龙. 基于空中机动目标拦截的制导和引信及战斗部一体化设计研究[J]. 兵工学报, 2020, 41(4): 649-655.
[14]	成丽蓉，汪德武，贺元吉. 侵彻单层和多层靶时战斗部装药损伤及热点生成机理研究[J]. 兵工学报, 2020, 41(1): 32-39.
[15]	李茂，侯海量，李典，陈鹏宇，李永清，朱锡. 动态爆炸战斗部对舰船舱壁的破片载荷特性研究[J]. 兵工学报, 2019, 40(9): 1804-1818.

对称刻槽预控破片战斗部壳体爆炸过程质量损失率研究

Research on the Explosion Mass Loss Rate of Pre-formed Fragment Warhead Shell with Symmetric Groove

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价