拉拔成型无氧铜管在爆轰加载下的膨胀及断裂特性研究

doi:10.3969/j.issn.1000-1093.2019.08.011

摘要/Abstract

摘要： 为了探索拉拔成型无氧铜管是否满足标准圆筒试验的延展性要求，采用未经二次锻造的粗晶软态无氧铜，通过拉拔成型工艺加工成25 mm圆筒试验用的标准铜管。采用超高速分幅相机及扫描相机分别观测装填TNT炸药及JO-159炸药条件下的铜管膨胀及断裂过程，对比典型高应变率范围内铜管的断裂应变、裂纹扩展方向等差异，并分析铜管应变能对炸药驱动性能表征参数的影响。结果表明：TNT炸药爆轰加载下，铜管裂纹主要沿母线形成及扩展，其破片主要呈条状；而JO-159炸药爆轰加载下，铜管环向应变率及轴向应变率分别约为TNT炸药加载工况的1.34倍和2倍，其断裂带易出现较为复杂的交错状态，形成密集小破片；这两种炸药爆轰下，该铜管的断裂直径均达到了初始直径的3倍，且表征炸药驱动性能的格尼速度未发生明显变化，因此可以满足一般高能炸药圆筒试验的要求。

关键词: 无氧铜管, 拉拔成型, 爆轰加载, 断裂, 应变率

Abstract: In order to explore whether the drawn-molded oxygen-free copper tube meets the ductility requirements of standard cylinder test, a standard copper tube for SymbolFA@25 mm cylinder test was made of coarse-grained soft oxygen-free copper without secondary forging by using the drawing process. The high-speed framing camera and scanning camera were used to observe the expansion and fracture processes of copper tube under detonation loading of TNT and JO-159 explosives, and compare the difference of fracture strain and the direction of crack propagation in the typical high strain rate range. The influence of strain energy of copper tube on the characterization parameters of driving performance of explosive was also analyzed. The results show that the cracks of copper tubes are mainly formed and expanded along the busbar and the fragments are mainly strip-like under the detonation loading of TNT explosive. However, under the detonation loading of JO-159 explosive, a more complicated staggered state arises in the fracture zone, and the copper tube expands to form dense small fragments. The main reason for this phenomenon is that the circumferential and axial strain rates of copper tubes under detonation loading of JO-159 explosive are 1.34 and 2 times of those under detonation loading of TNT. Under the detonation loading of these two kinds of explosives, the fracture diameter reaches 3 times of the initial diameter, and the Gurney speed, which characterizes the driving performance of explosives, is not changed significantly. Therefore, the copper tubes can meet the requirements of the general high-energy explosives for cylinder test. Key

Key words: oxygen-freecoppertube, drawn-molding, detonationloading, crack, strainrate

中图分类号:

O383⁺.3

沈飞，王辉，李彪彪，张皋. 拉拔成型无氧铜管在爆轰加载下的膨胀及断裂特性研究[J]. 兵工学报, 2019, 40(8): 1634-1640.

SHEN Fei, WANG Hui, LI Biaobiao, ZHANG Gao. Research on the Expansion and Fracture Characteristics of Drawing-molded Oxygen-free Copper Tubes under Detonation Loading[J]. Acta Armamentarii, 2019, 40(8): 1634-1640.

参考文献

［1］奥尔连科 Л П. 爆炸物理学[M]. 孙承纬, 译. 北京: 科学出版社, 2011.
ORLENKO Л П. Explosion physics[M]. SUN C W, translated . Beijing: Science Press, 2011. (in Chinese)
[2］石德珂. 材料科学基础[M]. 北京: 机械工业出版社, 2000.
SHI D K. Fundamentals of material science[M]. Beijing: China Machine Press, 2000. (in Chinese)
[3］胡海波, 汤铁钢, 胡八一, 等. 金属柱壳在爆炸加载断裂中的单旋现象[J]. 爆炸与冲击, 2004, 24(2): 97-107.
HU H B, TANG T G, HU B Y, et al. A study of uniform shear bands orientation selection tendency on explosively loaded cylindrical shells[J]. Explosion and Shock Waves, 2004, 24(2): 97-107. (in Chinese)
[4］任国武, 郭昭亮, 汤铁钢, 等. 高应变率加载下金属柱壳断裂的实验研究[J]. 兵工学报, 2016, 37(1): 77-82.
REN G W, GUO Z L, TANG T G, et al. Experimental research on fracture of metal case under loading at high strain rate[J]. Acta Armamentrii, 2016, 37(1): 77-82. (in Chinese)
[5］李忠盛, 吴护林, 陈韵如, 等. 内爆炸载荷作用下7A55铝合金的动态性能及断裂行为[J]. 爆炸与冲击, 2012, 32(2): 190-195.
LI Z S, WU H L, CHEN Y R, et al. Dynamic properties and fracture behaviors of 7A55 aluminum alloy under explosive loading[J]. Explosion and Shock Waves, 2012, 32(2): 190-195. (in Chinese)
[6］ SINGH M, SUNEJA H R, BALA M S, et al. Dynamic tensile deformation and fracture of metal cylinders at high strain rates[J]. International Journal of Impact Engineering, 2002, 27(2): 939-954.
[7］ GOTO D M, BECKER R, ORZECHOWSKI T J, et al. Investigation of the fracture and fragmentation of explosively driven rings and cylinders[J]. International Journal of Impact Engineering, 2008, 35(12): 1547-1556.
[8］郭昭亮, 范诚, 刘明涛, 等. 爆炸与电磁加载下无氧铜环、柱壳的断裂模式转变[J]. 爆炸与冲击, 2017, 37(6): 1072-1079.
GUO Z L, FAN C, LIU M T, et al. Fracture mode transition in expanding ring and cylindrical shell under electromagnetic and explosive loadings[J]. Explosion and Shock Waves, 2017, 37(6): 1072-1079. (in Chinese)
[9］ REN G W, GUO Z L, FAN C, et al. Dynamic shear fracture of an explosively-driven metal cylindrical shell[J]. International Journal of Impact Engineer, 2016, 35(1): 77-82.

[10］董海山, 周芬芬. 高能炸药及相关物性能[M]. 北京: 科学出版社, 1989.
DONG H S, ZHOU F F. Performance of high explosives and correlates [M]. Beijing: Science Press, 1989. (in Chinese)
[11］沈飞, 王辉, 罗一鸣. DNTF基同轴双元装药的爆轰波形及驱动性能[J]. 含能材料, 2018, 26(7): 614-619.
SHEN F, WANG H, LUO Y M. Detonation wave-shape and driving performance of coaxial binary charge of DNTF-based aluminized explosives[J]. Chinese Journal of Energetic Materials, 2018, 26(7): 614-619. (in Chinese)
[12］ SOUERS P C, LAUDERBACH L, GARZA R, et al. Upgraded analytical model of the cylinder test[J]. Propellants, Explosives, Pyrotechnics, 2013, 38(3): 419-424.
[13］ HORNBERG H, VOLK F. The cylinder test in the context of physical detonation measurement methods[J]. Propellants, Explosives, Pyrotechnics, 1989, 14(5): 199-211.
[14］李亮亮, 沈飞, 王辉, 等．晶粒细化对无氧铜动态力学性能的影响[J]. 兵器材料科学与工程, 2019, 42(1): 22-25.
LI L L, SHEN F, WANG H, et al. Effect of grain refinement on dynamic mechanical properties of oxygen-free copper[J]．Ordnance Material Science and Engineering, 2019, 42(1): 22-25. (in Chinese)
[15］ SOUERS P C, MINICH R. Cylinder test correction for copper work hardening and spall[J]. Propellants, Explosives, Pyrotechnics, 2015, 40(2): 238-245.

第40卷
第8期2019 年8月兵工学报ACTA
ARMAMENTARIIVol.40No.8Aug.2019

[1]	王凡, 郭伟国, 吴倩, 高猛. 高应变率下高温应变计灵敏度系数的校准方法[J]. 兵工学报, 2022, 43(4): 899-909.
[2]	党泉勇，葛彦鑫，高玉波. 冲击加载下Al₂O₃/SiC复合陶瓷的动态力学行为[J]. 兵工学报, 2022, 43(1): 175-180.
[3]	宁子轩，王琳，程兴旺，程焕武，周哲，张斌斌，王芳，陈东萍. 微观组织对Ti6321钛合金靶板爆炸断裂失效的影响[J]. 兵工学报, 2021, 42(7): 1506-1515.
[4]	刘强，陈鹏万，苏健军，李芝绒，张玉磊. 碳化硅与聚脲纳米复合材料拉伸力学性能和本构模型[J]. 兵工学报, 2021, 42(6): 1238-1249.
[5]	宁子轩，王琳，程兴旺，程焕武，刘安晋，徐雪峰，周哲，张斌斌. 分离式霍普金森压杆加载下不同组织Ti-6321钛合金的动态响应行为[J]. 兵工学报, 2021, 42(4): 862-870.
[6]	彭嘉诚，蒋建伟，李响，李帅孝，陈永恒. 杀伤爆破弹弹体异常淬火时弹底大破片形成机理[J]. 兵工学报, 2021, 42(11): 2333-2343.
[7]	徐雪峰，王琳，程兴旺，刘安晋， Tayyeb Ali，周哲，宁子轩，张斌斌，赵登辉. Ti6321钛合金在Taylor杆冲击下的动态断裂微观组织观测[J]. 兵工学报, 2020, 41(7): 1401-1407.
[8]	付应乾，俞鑫炉，董新龙，周风华，宁建国，李平. 混凝土材料拉伸强度的应变率强化效应实验研究[J]. 兵工学报, 2020, 41(1): 143-151.
[9]	魏强，黄西成，陈刚，陈鹏万. 高聚物粘结炸药动态损伤破坏的数值刻画[J]. 兵工学报, 2019, 40(7): 1381-1389.
[10]	蔡宣明，张伟，徐鹏，高玉波，范志强. 一维应力动态加载下战斗部装药力学响应预报模型[J]. 兵工学报, 2019, 40(4): 762-768.
[11]	高玉波，秦国华，张伟，宜晨虹，邓勇军. TiB₂-B₄C复合陶瓷动态压缩特性研究[J]. 兵工学报, 2019, 40(11): 2304-2310.
[12]	段春争，刘玉敏，孙伟，车明帆. 增强颗粒对切削SiCp/Al复合材料切屑形成过程的影响机理[J]. 兵工学报, 2019, 40(1): 208-218.
[13]	张高峰，李向东，周兰伟，马丽英. 对称刻槽预控破片战斗部壳体爆炸过程质量损失率研究[J]. 兵工学报, 2018, 39(2): 254-260.
[14]	陈志闯，李伟兵，朱建军，王晓鸣，李文彬. 40CrMnSiB钢圆柱壳体膨胀断裂中间状态回收试验研究[J]. 兵工学报, 2018, 39(11): 2137-2144.
[15]	周鼎，苗应刚，王严培，李峰，李玉龙. 冲击载荷下硼酸改性端羟基聚硅氧烷-二氧化硅复合材料的响应特性[J]. 兵工学报, 2018, 39(1): 137-145.