高聚物粘结炸药动态损伤破坏的数值刻画

doi:10.3969/j.issn.1000-1093.2019.07.007

摘要/Abstract

摘要： 高聚物粘结炸药(PBX)安全性评估离不开对其力学响应和损伤破坏的刻画。为了准确捕捉PBX炸药的力学行为，以Karagozian & Case模型框架为基础，开展了PBX炸药力学行为数值刻画的研究。修改Karagozian & Case模型中的损伤演化方式，考虑PBX炸药模量、损伤演化模式等压力依赖特性。结合法国原子能委员会Picart等给出的一系列试验数据，修正Karagozian & Case模型中的应变率效应，分析不同压力下PBX炸药拉压子午线之比的取值，处理结构损伤破坏过程中变形局部化的问题，提出数值计算中拉伸失效单元的处理方法。得到的模型很好地刻画了Steven 试验中炸药试件的成坑形貌，并成功捕捉到了炸药试件中的拉伸、剪切破坏图像。

关键词: 高聚物粘结炸药, 拉伸、压缩子午线之比, 应变率效应, 变形局部化, 拉伸失效

Abstract: The safety assessment of PBX explosive is inseparable from the characterization of its mechanical response and damage. In order to accurately capture the mechanical behavior of PBX explosive, the numerical characterization method of PBX explosive mechanical behavior is studied based on Karagozian & Case (K&C) model framework. The damage evolution mode in the K&C model is modified, and the pressure-dependent characteristics of PBX explosive modulus and damage evolution mode are considered. Based on a series of published experimental data, the strain rate effect in the K&C model was corrected, the ratio of tension to compression meridian of PBX under different pressures was discussed, the deformation localization in the process of structural damage was dealt with, and the treatment of the tensile failure unit in the calculation was presented. The proposed model can be used to well depict the cratering morphology of explosive specimen in the Steven test, and successfully capture the tensile and shear failure images of explosive specimen. Key

Key words: polymerbondedexplosive, ratiooftensiletocompressionmeridian, strainrateeffect, strainlocalization, tensilefailure

中图分类号:

O347.3
TJ55

魏强，黄西成，陈刚，陈鹏万. 高聚物粘结炸药动态损伤破坏的数值刻画[J]. 兵工学报, 2019, 40(7): 1381-1389.

WEI Qiang, HUANG Xicheng, CHEN Gang, CHEN Pengwan. Numerical Characterization of Dynamic Damage of PBX Explosive[J]. Acta Armamentarii, 2019, 40(7): 1381-1389.

参考文献

［1］ STEWART J B. A pressure-dependent damage model for energetic materials: ARL-RP-436 ［R］. Aberdeen Proving Ground, MD, US: Army Research Laboratory,2013.
［2］ XIAO Y C, SUN Y, ZHEN Y B, et al. Characterization, modeling and simulation of the impact damage for polymer bonded explosives［J］. International Journal of Impact Engineering, 2017,103:149-158.
［3］ WANG X J, WU Y Q, HUANG F L, et al. Mesoscale thermal-mechanical analysis of impacted granular and polymer-bonded explosives［J］. Mechanics of Materials, 2016,99:68-78.
［4］ BARUA A, ZHOU M. A Lagrangian framework for analyzing microstructural level response of polymer-bonded explosives［J］. Modelling and Simulation in Materials Science and Engineering, 2011, 19(5): 055001.
［5］ LIU Z W, XIE H M, LI K X, et al. Fracture behavior of PBX simulation subject to combined thermal and mechanical loads［J］. Polymer Testing, 2009, 28(6):627-635.
［6］ ELLIS K, LEPPARD C, RADESK H. Mechanical properties and damage evaluation of a UK PBX［J］. Journal of Materials Science, 2005, 40(23):6241-6248.
［7］ ZHOU Z, CHEN P, DUAN Z, et al. Study on fracture behaviour of a polymer-bonded explosive simulant subjected to uniaxial compression using digital image correlation method［J］. Strain, 2012, 48(4):326-332.
［8］ PARTHA R, DARLA G T, LIU C,et al. Modeling the mechanical response of PBX 9501［C］∥Proceedings of the 14th International Detonation Symposium. Coeur d'Alene, ID, US: University of Maryland, 2010:174-183.
［9］ HERVE T, PHILIPPE L, GUILLAUME V, et al. Toward physically-based explosive modeling: meso-scale investigations［M］∥BUZAUD E, IONESCU I R, VOYIADJIS G Z. Materials under Extreme Loadings. London, UK: ISTE Ltd., 2013:179-207.

［10］ REAUGH J E. HERMES: A model to describe deformation, burning, explosion, and detonation: LLNL-TR-516119［R］. Livermore, CA, US: Lawrence Livermore National Laboratory, 2011.
［11］ GRUAU C, PICART D, BELMAS R, et al. Ignition of a confined high explosive under low velocity impact［J］. International Journal of Impact Engineering, 2009, 36(4):537-550.
［12］ GRATTON M, GONTIER C, RJA FI ALLAH S, et al. Mechanical characterization of a viscoplastic material sensitive to hydrostatic pressure ［J］. European Journal of Mechanics A/Solids, 2009, 28(5):935-947.
［13］ MALVAR L J, CRAWFORD J E, WESEVICH J W, et al. A plasticity concrete material model for DYNA3D［J］. International Journal of Impact Engineering, 1997, 19(9/10):847-873.
［14］ BAILLY P, DELVARE F, VIAL J, et al. Dynamic behavior of an aggregate material at simultaneous high pressure and strain rate: SHPB triaxial tests［J］. International Journal of Impact Engineering, 2011, 38(2/3):73-84.
［15］ WIEGAND D A, REDINGIUS B, ELLIS K, et al. Pressure and friction dependent mechanical strength-cracks and plastic flow［J］. International Journal of Solids and Structures, 2011, 48(11/12): 1617-1629.
［16］崔云霄, 陈鹏万, 刘龑龙, 等. PBX 9501炸药动态增强因子的预测公式［J］. 火炸药学报, 2015, 38(3):54-58.
CUI Y X, CHEN P W, LIU Y L, et al. Predicted formula of the dynamic increase factor of PBX9501［J］. Chinese Journal of Explosives & Propellants, 2015, 38(3):54-58.(in Chinese)
［17］ WIEGAND D A. Constant strain criteria for mechanical failure of energetic materials［J］. Journal of Energetic Materials, 2003, 21(2): 109-124.
［18］唐维. PBX炸药的准静态本构模型与强度准则［D］. 南京:南京理工大学, 2016.
TANG W. Quasi-static constitutive model and strength criterion for PBX explosives［D］. Nanjing:Nanjing University of Science and Technology, 2016. (in Chinese)
［19］黄西成, 李尚昆, 魏强, 等. 基于XFEM与Cohesive模型分析PBX裂纹产生与扩展［J］. 含能材料, 2017, 25(8):694-700.
HUANG X C, LI S K, WEI Q, et al. Analysis of crack initiation and growth in PBX energetic material using XFEM-based cohesive method［J］. Chinese Journal of Energetic Materials, 2017, 25(8): 694-700. (in Chinese)
［20］ GORDON R J, HOLMQUIST T J. Response of boron carbide subjected to large strains, high strain rates, and high pressures［J］. Journal of Applied Physics, 1999, 85(12):8060-8073.
［21］ RALPH M, THOMAS D S. Constituent properties of HMX needed for mesoscale simulations［J］. Combustion Theory and Modelling, 2002, 6(1):103-125.
［22］吕玺琳. 岩土材料应变局部化理论预测及数值模拟［D］. 上海:同济大学, 2008.
L X L. Theoretical prediction and numerical simulation of strain localization for geomaterials［D］. Shanghai:Tongji University, 2008.(in Chinese)
［23］ WANG X, MA S P, ZHAO Y T, et al. Observation of damage evolution in polymer bonded explosives using acoustic emission and digital image correlation［J］. Polymer Testing, 2011, 30(8):861-866.
［24］王小平, 孟国涛. 非局部化弹塑性理论及其应用［J］.岩土力学与工程学报, 2007, 26(增刊1):2964-2967.
WANG X P, MENG G T. Nonlocal elastoplastic theory and its application［J］. Chinese Journal of Rock Mechanics and Engineering. 2007, 26(S1): 2964-2967.(in Chinese)
［25］ VIAL J, PICART D, BAILLY P, et al. Numerical and experimental study of the plasticity of HMX during a reverse edge-on impact test［J］.Modelling and Simulation in Materials Science and Engineering, 2013, 21(4): 045006.
［26］ GRUAU C, PICART D. Numerical prediction of high explosive ignition under low velocity impact［J］. Foundations of Civil and Environmental Engineering, 2008, 1:33-48.

第40卷
第7期2019 年7月兵工学报ACTA
ARMAMENTARIIVol.40No.7Jul.2019

[1]	张仲昊, 汪维, 张国凯, 王振, 吴汩. 不同高温作用后混凝土劣化损伤性能[J]. 兵工学报, 2023, 44(S1): 152-159.
[2]	党泉勇，葛彦鑫，高玉波. 冲击加载下Al₂O₃/SiC复合陶瓷的动态力学行为[J]. 兵工学报, 2022, 43(1): 175-180.
[3]	刘纯，欧卓成，段卓平，黄风雷. 动态加载下高聚物粘结炸药中椭圆孔洞坍塌引起的热点温度及其半经验解析表达[J]. 兵工学报, 2022, 43(1): 57-68.
[4]	白志玲，段卓平，黄风雷. 高聚物粘结炸药冲击起爆统计热点反应速率模型[J]. 兵工学报, 2021, 42(11): 2379-2387.
[5]	秦金凤，赵雪，钱华，芮久后. 高致密球形黑索今晶体结构对高聚物粘结炸药安全性能的影响[J]. 兵工学报, 2020, 41(3): 481-487.
[6]	蔡宣明，张伟，徐鹏，高玉波，范志强. 一维应力动态加载下战斗部装药力学响应预报模型[J]. 兵工学报, 2019, 40(4): 762-768.
[7]	高玉波，秦国华，张伟，宜晨虹，邓勇军. TiB₂-B₄C复合陶瓷动态压缩特性研究[J]. 兵工学报, 2019, 40(11): 2304-2310.
[8]	李潘，郝志明，刘永平，甄文强. 基于近场动力学非普通状态理论的高聚物粘结炸药损伤破坏模拟研究[J]. 兵工学报, 2018, 39(5): 893-900.
[9]	王严培，姜启帆，李玉龙. 基于Hopkinson杆试验技术的PA-GF50复合材料动态力学行为[J]. 兵工学报, 2018, 39(1): 161-169.
[10]	欧亚鹏，闫石，焦清介，郭学永，孙亚伦. 浇注高聚物粘结炸药的粘结剂体系设计及其应用研究[J]. 兵工学报, 2018, 39(1): 63-70.
[11]	王竟成，罗景润. 不同细观力学方法预测高聚物粘结炸药有效模量的比较[J]. 兵工学报, 2017, 38(6): 1106-1112.
[12]	崔云霄，陈鹏万，郭保桥， David A. Cendón，周忠彬. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态断裂行为研究[J]. 兵工学报, 2017, 38(12): 2379-2385.
[13]	崔云霄，陈鹏万， David A. Cendón，戴开达，钟方平. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态巴西实验的数值模拟[J]. 兵工学报, 2016, 37(9): 1639-1645.
[14]	白志玲，段卓平，景莉，刘益儒，欧卓成，黄风雷. 飞片冲击起爆高能钝感高聚物粘结炸药的实验研究[J]. 兵工学报, 2016, 37(8): 1464-1468.
[15]	唐贤进，张丘，邹刚，吴松，刘维，尹锐. 基于径向基函数神经网络的高聚物粘结炸药切削表面粗糙度预测研究[J]. 兵工学报, 2014, 35(2): 200-206.