高温下奥克托今单晶冲击响应数值计算

doi:10.3969/j.issn.1000-1093.2021.05.009

摘要/Abstract

摘要： 为研究奥克托今(HMX)单晶在高温下的冲击响应，发展了基于热激活和声子拖曳位错滑移机制的非线性热弹黏塑性模型。该模型可再现平板撞击实验中HMX单晶Hugoniot弹性极限(HEL)的热硬化效应。通过定量分析声子散射和辐射阻尼对热硬化效应的影响，可研究373 K、423 K高温下受冲击HMX单晶位错滑移机制演变以及相关热力学响应。结果表明：随着初温由300 K升高至423 K，声子散射和辐射阻尼效应增强导致声子拖曳系数增大，使可移动位错黏性摩擦增强，平均位错速度由2 237 m/s减小至1 537 m/s，进而产生较低的塑性剪应变率和较高的流动应力，引起HMX单晶HEL的热硬化效应；剪切模量随着初温升高变化较小(约1.0 GPa)，导致辐射阻尼对热硬化效应的贡献小于声子散射。

关键词: 奥克托今, 高温, Hugoniot弹性极限, 热硬化, 位错滑移机制

Abstract: A nonlinear thermoelastic-viscoplastic model is developed for studying the thermodynamic response of octogen (HMX) single crystal at elevated temperatures, in which the thermal activation and phonon drag dislocation glide regime are considered. The proposed model can reproduce the thermal hardening behavior of Hugoniot elastic limit (HEL) of HMX single crystal in plate impact experiment. The effects of phonon scattering and radiation damping on the thermal hardening behavior are quantitatively analyzed to investigate the evolution of dislocation glide regime and the thermodynamic response at 373 K and 423 K. It is found that the thermal hardening behavior of HEL of HMX single crystal is due to the increase in phonon scattering and radiation damping with the initial temperature from 300 K to 423 K. The phonon drag coefficient is increased to strengthen the viscous friction of mobile dislocation. Therefore, the average dislocation velocity decreases from 2 237 m/s to 1 537m/s, which leads to slower plastic shear strain rate and higher flow stress. The shear modulus changes slightly with the increase in temperature (about 1.0 GPa), thus the contribution of radiation damping to thermal hardening is less than that of phonon scattering.

Key words: octogen, elevatedtemperature, Hugoniotelasticlimit, thermalhardening, dislocationglideregime

中图分类号:

O389
TJ55

丁凯, 王昕捷, 黄亨建, 吴艳青, 黄风雷. 高温下奥克托今单晶冲击响应数值计算[J]. 兵工学报, 2021, 42(5): 968-978.

DING Kai, WANG Xinjie, HUANG Hengjian, WU Yanqing, HUANG Fenglei. Numerical Calculation of Thermodynamic Response of Shocked HMX Single Crystal at Elevated Temperatures[J]. Acta Armamentarii, 2021, 42(5): 968-978.

参考文献

［1］ DICK J J. Effect of crystal orientation on shock initiation sensitivity of pentaerythritol tetranitrate explosive［J］. Applied Physics Letters, 1984, 44(9):859-861.
［2］ DICK J J, MULFORD R N, SPENCER W J, et al. Shock response of pentaerythritol tetranitrate single crystals［J］. Journal of Applied Physics, 1991, 70(7):3572-3587.
［3］ DICK J, RITCHIE J. Molecular mechanics modeling of shear and the crystal orientation dependence of the elastic precursor shock strength in pentaerythritol tetranitrate［J］. Journal of Applied Physics, 1994, 76(5):2726-2737.
［4］ DICK J J, MARTINEZ A R. Elastic precursor decay in HMX explosive crystals［J］. AIP Conference Proceedings, 2002, 620:817- 820.
［5］ DICK J J, HOOKS D E, MENIKOFF R, et al. Elastic-plastic wave profiles in cyclotetramethylene tetranitramine crystals［J］. Journal of Applied Physics, 2004, 96(1):374-379.
［6］ WINEY J M, GUPTA Y M. Anisotropic material model and wave propagation simulations for shocked pentaerythritol tetranitrate single crystals［J］. Journal of Applied Physics, 2010, 107(10):103505.
［7］ BARTON N R, WINTER N W, REAUGH J E. Defect evolution and pore collapse in crystalline energetic materials［J］. Modelling and Simulation in Materials Science and Engineering, 2009, 17(3): 035003.
［8］ WU Y Q, HUANG F L. Thermal mechanical anisotropic constitutive model and numerical simulations for shocked β-HMX single crystals［J］. European Journal of Mechanics A/Solids, 2012, 36:66-82.
［9］ WANG X J, WU Y Q, HUANG F L, et al. Dynamic anisotropic response of β-HMX and α-RDX single crystals using plate impact experiments at ~1 GPa［J］. Propellants, Explosives, Pyrotechnics, 2018, 43(8):759-770.
［10］ WANG X J, WU Y Q, HUANG F L, et al. An anisotropic elastoviscoplasticity model of thermomechanical responses of shocked β-HMX and α-RDX single crystals［J］. Propellants, Explosives, Pyrotechnics, 2019, 44(7):870-888.
［11］ KRASNIKOV V S, MAYER A E, YALOVETS A P. Dislocation based high-rate plasticity model and its application to plate-impact and ultra short electron irradiation simulations［J］. International Journal of Plasticity, 2011, 27(8):1294-1308.
［12］ GURRUTXAGA-LERMA B, SHEHADEH A M, BALINT D S, et al. The effect of temperature on the elastic precursor decay in shock loaded FCC aluminum and BCC iron［J］. International Journal of Plasticity, 2017, 96:135-155.
［13］ AUSTIN R. Elastic precursor wave decay in shock-compressed aluminum over a wide range of temperature［J］. Journal of Applied Physics, 2018, 123(3):035103-1-035103-14.
［14］ YAO S L, PEI X Y, LIU Z L, et al. Numerical investigation of the temperature dependence of dynamic yield stress of typical BCC metals under shock loading with a dislocation-based constitutive model［J］. Mechanics of Materials, 2019, 140:103211.
［15］ KOSITSKI R, MORDEHAI D. On the origin of the stress spike decay in the elastic precursor in shocked metals［J］. Journal of Applied Physics, 2019, 126(8):085901.
［16］ KANEL G I, SAVINYKH A S, GARKUSHIN G V, et al. Effects of temperature on the flow stress of aluminum in shock waves and rarefaction waves［J］. Journal of Applied Physics, 2020, 127(3):035901.
［17］ AUSTIN R A, MCDOWELL D L. A dislocation-based constitutive model for viscoplastic deformation of fcc metals at very high strain rates［J］. International Journal of Plasticity, 2011, 27(1): 1-24.
［18］ LUSCHER D J, BUECHLER M A, WALTERS D J, et al. On computing the evolution of temperature for materials under dynamic loading［J］. International Journal of Plasticity, 2018, 111:188-210.
［19］ STEINBERG D J, COCHRAN S G, GUINAN M W, et al. A constitutive model for metals applicable at high-strain rate［J］. Journal of Applied Physics, 1980, 51(3):1498-1504.
［20］ LUKYANOV A A. Constitutive behaviour of anisotropic materials under shock loading［J］. International Journal of Plasticity, 2008, 24(1):140-167.
［21］ PALMER S J P, FIELDJ E. The deformation and fracture of β-HMX［J］. Proceedings of the Royal Society of London . Series A, Mathematical and Physical Sciences, 1982, 383(1785):399- 407.
［22］ CUI H L, JI G F, CHEN X R, et al. Phase transitions and mechanical properties of octahydro-1，3，5，7-tetranitro-1，3，5，7-tetrazocine in different crystal phases by molecular dynamics simulation［J］. Journal of Chemical & Engineering Data, 2010, 55(9): 3121-3129.
［23］ BISHOP J F W, HILL R. XLVI. A theory of the plastic distortion of a polycrystalline aggregate under combined stresses［J］. The London, Edinburgh and Dublin Philosophical Magazine and Journal of Science, 1951, 42(327):414-427.
［24］ GILMAN J J, JOHNSTON W G. Dislocations in lithium fluoride crystals［J］. Solid State Physics, 1962, 13:147-222.
［25］ FOLLANSBEE P S, KOCKS U F. A constitutive description of the deformation of copper based on the use of the mechanical threshold stress as an internal state variable［J］. Acta Metallurgica, 1988, 36(1):81-93.
［26］ KOCKS U F, MECKING H. Physics and phenomenology of strain hardening: the FCC case［J］. Progress in Materials Science, 2003, 48(3):171-273.
［27］ KOCKS U F, ARGON A S, ASHBY M F. Thermodynamics and
kinetics of slip［M］∥Chalmers B, Christian J W, Massalski T B.
Progress in Materials Science. Oxford, UK: Pergamon Press, 1975: 141-145.
［28］ TAYLOR G I. The mechanism of plastic deformation of crystals. Part Ⅱ. Comparison with observations［J］. Proceedings of the Royal Society. Series A, Containing Papers of a Mathematical and Physical Character, 1934, 145(855):388-404.
［29］ WINEY J M, GUPTA Y M. Nonlinear anisotropic description for the thermomechanical response of shocked single crystals: inelastic deformation［J］. Journal of Applied Physics, 2006, 99(2):023510.
［30］ GUPTA Y M, DUVALL G E, FOWLES G R． Dislocation me-chanisms for stress relaxation in shocked LiF［J］. Journal of Applied Physics, 1975, 46(2):532-546.
［31］ HULL D, BACON D J. Introduction to dislocations［J］. Materials Today, 2011, 19(12):91-92.
［32］ CLIFTON R J. On the analysis of elastic/visco-plastic waves of finite uniaxial strain［C］∥Proceedings of Sagamore Army Materials Research Conference. Syracuse, NY, US: Syracuse University Press, 1971:73-116.
［33］ ARMSTRONG R W, ELBAN W L. Materials science and technology aspects of energetic (explosive) materials［J］. Materials Science and Technology, 2013, 22(4):381-395.
［34］丁凯, 王昕捷, 吴艳青,等. 高温下奥克托今单晶的冲击响应特性［J］. 兵工学报, 2020, 41(9):1783-1791.
DING K, WANG X J, WU Y Q, et al. Shock response of HMX single crystal at elevated temperatures［J］. Acta Armamentarii, 2020, 41(9):1783-1791. (in Chinese)
［35］ MARSH S P. LASL shock Hugoniot data［M］. Berkeley, CA, US: University of California Press, 1980:165-166.
［36］ BARRIOS M A, BOEHLY T R, HICKS D G, et al. Precision equation-of-state measurements on National Ignition Facility ablator materials from 1 to 12 Mbar using laser-driven shock waves［J］. Journal of Applied Physics, 2012, 111(9):093515.
［37］ JONES S C, GUPTA Y M. Refractive index and elastic properties of z-cut quartz shocked to 60 kbar［J］. Journal of Applied Physics, 2000, 88(10):5671-5679.
［38］ AO T, KNUDSON M D, ASAY J R, et al. Strength of lithium fluoride under shockless compression to 114 GPa［J］. Journal of Applied Physics, 2009, 106(10):103507
［39］ LALONE B M, FATYANOV O V, ASAY J R, et al. Velocity correction and refractive index changes for ［100］ lithium fluoride optical windows under shock compression, recompression, and unloading［J］. Journal of Applied Physics, 2008, 103(9):093505.

[1]	张程，张玉琦，温相丽，白鹏鹏，孟永钢，马丽然，田煜. 身管材料的高温氧化行为[J]. 兵工学报, 2024, 45(4): 1354-1362.
[2]	徐京, 胡春东, 陆恒昌, 邓亚辉, 薛钧, 韦习成, 董瀚. 枪管用环保镀层摩擦行为研究[J]. 兵工学报, 2024, 45(2): 651-661.
[3]	宁克焱, 曾强, 田金山, 赵攀, 兰海, 何家富, 万丽. 高温环境下弹簧功能-传感共形位移测量装置及方法[J]. 兵工学报, 2024, 45(2): 662-670.
[4]	李云飞, 高鑫, 陈鹏万, 刘开源. TiB₂/B₄C复相陶瓷自蔓延热爆炸烧结与性能表征[J]. 兵工学报, 2024, 45(1): 26-34.
[5]	张仲昊, 汪维, 张国凯, 王振, 吴汩. 不同高温作用后混凝土劣化损伤性能[J]. 兵工学报, 2023, 44(S1): 152-159.
[6]	王凡, 郭伟国, 吴倩, 高猛. 高应变率下高温应变计灵敏度系数的校准方法[J]. 兵工学报, 2022, 43(4): 899-909.
[7]	王雪蓉，孙岩，王倩倩，姚凯，孟祥艳，周燕萍，刘运传，马衍东. 基于下落式量热法的碳化硅陶瓷高温比热容测试[J]. 兵工学报, 2022, 43(1): 169-174.
[8]	冯晓军，薛乐星，冯博，潘文. “外嵌内包”微结构的奥克托今/铝复合粒子制备及其应用性能[J]. 兵工学报, 2021, 42(8): 1631-1637.
[9]	沈浩，蔡杰，吕鹏，张从林，李玉新，关庆丰. 激光工艺参数对NiCoCrAlYSi熔覆层微观组织及性能的影响[J]. 兵工学报, 2021, 42(7): 1524-1534.
[10]	许仁翰，周钇捷，狄长安. 基于高速成像的爆炸温度场测试方法[J]. 兵工学报, 2021, 42(3): 640-647.
[11]	丁凯，王昕捷，吴艳青，黄风雷. 高温下奥克托今单晶的冲击响应特性[J]. 兵工学报, 2020, 41(9): 1792-1799.
[12]	齐晓飞，谢五喜，严启龙，刘庆，刘春. 中性聚合物键合剂与奥克托今的界面作用[J]. 兵工学报, 2017, 38(10): 1942-1949.
[13]	史要涛，陈守谦，万子南，李韬，张爱红，范志刚，于翠萍，于创利. 强光干扰高温稀疏体系辐射能量计算方法研究[J]. 兵工学报, 2016, 37(5): 866-871.
[14]	刘海，何远航. 梯恩梯/萘共晶初始热分解的反应分子动力学模拟[J]. 兵工学报, 2016, 37(3): 414-423.
[15]	郝晓剑，桑涛，潘保武，周汉昌. 钽-氧化锆光纤黑体腔温度传感器特性参数测试[J]. 兵工学报, 2016, 37(2): 373-378.