悬臂式低压铸造机设计与稳定性分析

doi:10.3969/j.issn.1000-1093.2019.08.020

兵工学报 ›› 2019, Vol. 40 ›› Issue (8): 1700-1707.doi: 10.3969/j.issn.1000-1093.2019.08.020

悬臂式低压铸造机设计与稳定性分析

刘志刚¹，安建飞²，史晓平¹，裴承慧¹，黄东男¹，温海军²

(1.内蒙古工业大学机械工程学院, 内蒙古呼和浩特 010051；2.内蒙古北方重工业集团有限公司, 内蒙古包头 014033)

收稿日期:2018-09-18 修回日期:2018-09-18 上线日期:2019-10-15
作者简介:刘志刚(1974—)，男，副教授，硕士生导师，博士。E-mail: Lzhg2008@126.com
基金资助:
国家自然科学基金项目（51364027）

Design and Stability Analysis of Cantilever Low Pressure Casting Machine

LIU Zhigang¹, AN Jianfei², SHI Xiaoping¹, PEI Chenghui¹, HUANG Dongnan¹, WEN Haijun²

(1.College of Mechanical Engineering, Inner Mongolia University of Technology, Hohhot 010051, Inner Mongolia, China;2.Inner Mongolia North Heavy Industries Group Co., Ltd., Norinco Group, Baotou 014033, Inner Mongolia, China)

Received:2018-09-18 Revised:2018-09-18 Online:2019-10-15

摘要/Abstract

摘要： 目前四立柱式低压铸造机操作空间狭小，对于需要多开模、下砂芯的腔室类铸件存在诸多不便。为此，设计了一款主副悬臂同步摆转、工作台以上空间可完全开放的悬臂式低压铸造机。运用流体力学相关知识，分别求得铸造机在充型阶段、保压阶段、铸件卸载阶段主悬臂所受作用力，其中向上最大冲击力为35 302 N、最大重力为4 606 N. 根据铸造机浇注时上模与侧模之间允许最大间隙，设计主悬臂采用长度为1 200 mm、外径为270 mm、内径为235 mm的Q235A空心圆钢。运用有限元法对悬臂结构进行仿真分析，结果显示悬臂上模油缸处最大变形量为1.8 mm. 对所设计悬臂式低压铸造机进行样机制作和现场试验，其所生产的铸件满足军工产品的性能要求。当铸造机进入保压阶段时，上模和侧模之间的距离为1.92 mm，在允许的安全间隙之内。

关键词: 低压铸造机, 悬臂式, 结构设计, 稳定性分析, 仿真分析

Abstract: The operating space of four-column low-pressure casting machine is very narrow, so it is inconvenient for the production of cavity castings with multi-openings and sand cores. A low pressure casting machine with main and auxiliary cantilevers which swing synchronously and the completely opened space above the worktable was designed. The forces acting on the main cantilever during the filling, holding and unloading stages of the castings were calculated by using the relevant knowledge of fluid mechanics. The maximum impact force is 35 302 N, and the maximum gravity is 4 606 N. According to the maximum clearance between the upper mold and the side mold, the main cantilever is made of Q235A hollow round steel with length of 1 200 mm, outer diameter of 270 mm and inner diameter of 235 mm. The finite element method was used to simulate and analyze the cantilever structure. The results show that the maximum deformation is 1.8 mm at the oil cylinder of upper die of cantilever. The cantilever low pressure casting machine prototype was test, which meets the performance requirements of military products. When the caster enters the packing stage, the distance between the upper mold and the side mold is 1.92 mm, which is within the allowable safety clearance. Key

Key words: lowpressurecastingmachine, cantilever, structuraldesign, stabilityanalysis, simulationanalysis

中图分类号:

TG233⁺.1

刘志刚，安建飞，史晓平，裴承慧，黄东男，温海军. 悬臂式低压铸造机设计与稳定性分析[J]. 兵工学报, 2019, 40(8): 1700-1707.

LIU Zhigang, AN Jianfei, SHI Xiaoping, PEI Chenghui, HUANG Dongnan, WEN Haijun. Design and Stability Analysis of Cantilever Low Pressure Casting Machine[J]. Acta Armamentarii, 2019, 40(8): 1700-1707.

参考文献

［1］郑小秋, 谢世坤, 易荣喜, 等. 低压铸造技术:发展历程、研究现状和未来趋势[J]. 材料导报, 2016, 30(4):74-80.
ZHENG X Q, XIE S K, YI R X, et al.Low-pressure casting:retrospect, perspect and prospect[J].Materials Review, 2016, 30(4): 74-80.(in Chinese)
[2］ JIANG W M, FAN Z T. Gating system optimization of low pressure casting A356 aluminum alloy intake manifold based on numerical simulation[J]. China Foundry, 2014, 11(2):119-124.
[3］ ABHILASH V, MANU M V, SAVITHRI S. et al. Numerical simulation and experimental validation of free surface flows during low pressure casting process[J]. Journal of Materials Processing Technology, 2017, 244:320-330.
[4］冀焕明, 罗天骄, 杨院生. AZ80镁合金低压脉冲磁场半连续铸造过程的数值模拟和实验研究[J]. 中国有色金属学报, 2017, 27(3): 468-476.
JI H M, LUO T J, YANG Y S. Numerical simulation and experimental research of low voltage pulsed magnetic field DC casting of AZ80 magnesium alloy[J]. The Chinese Journal of Nonferrous Metals, 2017, 27(3):468-476.(in Chinese)
[5］ HORR A M, ANGERMEIER C, HARRISON A. Full through process simulation for low pressure die casting-from casting to design[J]. Materials Science Forum, 2014, 3225(794): 118-123.
[6］赵世季, 赵强. 镁合金机械臂低压铸造的数值仿真[J]. 热加工工艺, 2018, 47(5): 121-124.
ZHAO S J, ZHAO Q. Numerical simulation of low pressure casting of magnesium alloy mechanical arm[J]. Hot Working Technology, 2018, 47(5): 121-124.(in Chinese)
[7］江玉华. 中国低压铸造装备面临的机遇和挑战[J]. 铸造技术, 2007(12): 1572.
JIANG Y H. Opportunity and challenge for China low pressure casting equipments[J]. Foundry Technology, 2007(12):1572.(in Chinese)
[8］安建飞, 周锦华, 史晓平. 杠杆式悬臂低压铸造机：中国, CN206912216U[P]. 2018-01-23.
AN J F, ZHOU J H, SHI X P. Lever type cantilever low pressure casting machine:CN106914604A[P]. 2018-01-23.(in Chinese)
[9］吴晓明, 陈丽缓, 彭立广, 等.基于AMESim的低压铸造机液面加压系统的优化设计与分析[J]. 机床与液压, 2014, 42(10): 83-86.
WU X M, CHEN L H, PENG L G, et al. Optimization design and analysis of the low pressure casting surface pressure system based on AMESim[J]. Machine Tool & Hydraulics, 2014, 42(10):83-86. (in Chinese)

[10］秦家升, 赵继云, 王晓倩, 等.挖掘机液压冲击问题分析[J]. 机床与液压, 2008,36(9):273-275.
QIN J S, ZHAO J Y, WANG X Q, et al. Analysis of the hydraulic impact in excavator[J]. Machine Tool & Hydraulics, 2008,36(9):273-275.(in Chinese)
[11］许福玲, 陈尧明. 液压与气压传动[M]. 北京：机械工业出版社,2012.
XU F L, CHEN Y M. Hydraulic and pneumatic transmission[M]. Beijing: China Machine Press, 2012.(in Chinese)
[12］张伟博. 平衡挖掘机节能机理分析与研究[D]. 西安：长安大学,2012.
ZHANG W B. Analysis and research on the energy-saving me-chanism of balance excavator[D]. Xi'an：Chang'an University, 2012.(in Chinese)
[13］梅帅,陈飙松,张盛,等.开放式结构拓扑优化软件设计与研发[J].机械工程学报,2015,51(9):144-152.
MEI S, CHEN B S, ZHANG S, et al. Design and development of open style software system for structural topology optimization [J]. Journal of Mechanical Engineering, 2015,51(9): 144-152.(in Chinese)
[14］李志强, 张运章, 宋艳丽. 应力和位移约束下连续结构的有效拓扑优化方法[J]. 应用力学学报, 2013, 30(1):70- 75.
LI Z Q, ZHANG Y Z, SONG Y L. An efficient structural topological optimization method for continuum structures with stress and displacement constraints[J]. Chinese Journal of Applied Mechanics, 2013, 30(1): 70-75. (in Chinese)
[15］孙全兆, 杨国来, 葛建立.某火炮上架结构改进设计[J].兵工学报, 2012, 33(11):1281-1285.
SUN Q Z, YANG G L, GE J L. Improved design for top carriage of a gun[J]. Acta Armamentarii, 2012, 33(11):1281-1285. (in Chinese)
[16］田劼, 王苏彧, 穆晶, 等. 悬臂式掘进机空间位姿的运动学模型与仿真[J]. 煤炭学报, 2015, 40(11):2617-2622.
TIAN J, WANG S Y, MU J, et al. Spatial pose kinematics mo-del and simulation of boom-type roadheader[J]. Journal of China Coal Society, 2015, 40(11):2617-2622.(in Chinese)
[17］赵海东, OHNAKA I. 铝合金铸件充型过程及氧化膜卷入的数值模拟[J]. 中国有色金属学报, 2005,15(8):1200-1207.
ZHAO H D, OHNAKA I. Numerical simulation of oxide entrapment and mold filling process of Al casting [J]. The Chinese Journal of Nonferrous Metals, 2005, 15(8):1200-1207.(in Chinese)

第40卷
第8期2019 年8月兵工学报ACTA
ARMAMENTARIIVol.40No.8Aug.2019

[1]	王盼，吴昊，梁宇，胡雪岑，纪雪松，王振宇. 轻型无人机起落架设计与强度分析[J]. 兵工学报, 2022, 43(S1): 140-145.
[2]	荣吉利，宋逸博，王玺，郭振，项大林，吴志培. 核爆炸对地冲击作用下土体运动特性等效模拟[J]. 兵工学报, 2021, 42(1): 56-64.
[3]	赵正龙，宋彬，吕建刚，何忠波，戴志广. 一种全金属网面轮胎的设计、仿真与试验研究[J]. 兵工学报, 2020, 41(4): 771-782.
[4]	何威，魏彦京. 悬臂式电磁发射导轨及壁板在发射状态下的强度分析[J]. 兵工学报, 2020, 41(1): 21-31.
[5]	孙嘉庆, 陈聪, 危玉倩, 李定国. 微分递推法在舰船静态电场深度换算中的应用研究[J]. 兵工学报, 2018, 39(2): 345-355.
[6]	王钰，于纪言，王晓鸣，冯斌. 修正组件结构参数对旋转稳定弹道修正弹稳定性的影响研究[J]. 兵工学报, 2018, 39(10): 1910-1918.
[7]	卢家莉，李彬华，胡泊. 一种电子倍增CCD电子倍增增益的确定方法[J]. 兵工学报, 2015, 36(4): 710-715.
[8]	刘坚成，黄风雷，皮爱国，申超. 定心式弹托对弹体侵彻混凝土效应影响规律研究[J]. 兵工学报, 2015, 36(3): 451-456.
[9]	徐浩铭, 顾文彬, 刘建青, 赵长啸, 徐尉友, 胡亚锋. 串联聚能装药隔爆结构设计数值模拟和实验研究[J]. 兵工学报, 2014, 35(2): 170-175.
[10]	李杰, 刘俊. 制导弹药用微惯性测量单元结构设计[J]. 兵工学报, 2013, 34(6): 711-717.
[11]	石志彬, 高敏, 杨锁昌, 魏保华. 瞄准式战斗部杀伤装置结构设计研究[J]. 兵工学报, 2013, 34(3): 373-377.
[12]	李长生，张合. 基于磁共振的引信用能量和信息无线同步传输方法研究[J]. 兵工学报, 2011, 32(5): 537-542.
[13]	梁志刚, 马艳军₂, 秦学军₂, 钟方平₂, 霍宏发₂, 张小良₂, 陈花玲₁. 小当量双层爆炸容器的研制[J]. 兵工学报, 2010, 31(4): 525-528.
[14]	裴譞，张宇文，袁绪龙，张纪华. 潜载导弹垂直发射横向振动特性仿真分析[J]. 兵工学报, 2009, 30(8): 1056-1060.
[15]	王向华，覃征，杨慧杰，杨新宇. 基干“当前”统计模型的模糊自适应跟踪算法[J]. 兵工学报, 2009, 30(8): 1089-1093.

悬臂式低压铸造机设计与稳定性分析

Design and Stability Analysis of Cantilever Low Pressure Casting Machine

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价