浇注高聚物粘结炸药的粘结剂体系设计及其应用研究

doi:10.3969/j.issn.1000-1093.2018.01.007

摘要/Abstract

摘要： 为提高端羟基聚丁二烯(HTPB)基浇注高聚物粘结炸药(PBX)的固相含量、力学性能，并降低渗油性，采用己二酸二辛酯和壬酸异癸酯为原料，根据溶度参数近似原理设计了一种复合增塑剂AI.基于HTPB/AI粘结剂体系制备出固相含量达到90%的浇注PBX，研究了PBX的机械感度、热分解、固相含量等与粘结剂体系的关系。结果表明：复合增塑剂AI降低了HTPB胶片的模量，从而降低了PBX的机械感度；AI降低了浇注PBX药浆黏度，提高了固相含量，从而提升了能量水平；对原材料进行高温真空旋蒸处理，降低了原材料中水分等杂质的含量，从而降低了PBX的渗油性，提高了复合增塑剂的安定性及其与PBX配方中其他组分的相容性。

关键词: 高聚物粘结炸药, 复合增塑剂, 高固相含量, 渗油率

Abstract: In order to improve the solid content and mechanical properties, and decrease the plasticizer migration of hydroxyl terminated polybutadiene (HTPB) based castable polymer bonded explosive (PBX), a compound plasticizer (AI) was designed according to the approximation principle of solubility parameter using dioctyl adipate and isodecyl pelargonate as substances. The solid phase content of castable PBX based on HTPB/AI binder system reachs 90% using conventional practice. The influence of binder system on mechanical sensitivity, compatibility, performance and other properties were investigated. The results show that AI decreases the tensile modulus of HTPB film, thus decreasing its mechanical sensitivity. The viscosity at the end of mix of PBX slurry is decreased and the performance is improved due to the high solid content. Vacuum high temperature rotary evaporation of raw materials removes impurities and keeps plasticizer from leakage with the ideal compatibility. Key

Key words: polymerbondedexplosive, compoundplasticizer, highsolidphasecontent, plasticizermigration

中图分类号:

TQ564.4

欧亚鹏，闫石，焦清介，郭学永，孙亚伦. 浇注高聚物粘结炸药的粘结剂体系设计及其应用研究[J]. 兵工学报, 2018, 39(1): 63-70.

OU Ya-peng, YAN Shi, JIAO Qing-jie, GUO Xue-yong, SUN Ya-lun. Design and Application of Binder System for Castable Polymer Bonded Explosive[J]. Acta Armamentarii, 2018, 39(1): 63-70.

参考文献

［1］罗观, 殷明, 郑保辉, 等. 高格尼能钝感浇注PBX设计及性能［J］. 含能材料, 2014, 22(4):487-492.
LUO Guan, YIN Ming, ZHENG Bao-hui, et al. Design and performance of an insensitive cast PBX with high gurney energy［J］. Chinese Journal of Energetic Materials, 2014, 22(4):487-492. (in Chinese)
［2］ Xiao J, Wang W, Chen J, et al. Study on the relations of sensitivity with energy properties for HMX and HMX-based PBXs by molecular dynamics simulation［J］. Physica B Condensed Matter, 2012, 407(17):3504-3509.
［3］ Vadhe P P, Pawar R B, Sinha R K, et al. Cast aluminized explosives (review)［J］. Combustion, Explosion, and Shock Waves, 2008, 44(4):461-477.
［4］谢虓, 肖承, 罗观. HMX基浇注PBX药浆表观黏度的实验研究［J］. 火炸药学报, 2015, 38(2):58-61.
XIE Xiao, XIAO Cheng, LUO Guan. Experimental study on the apparent viscosity of HMX-based casting PBX slurry［J］. Chinese Journal of Explosives & Propellants, 2015, 38(2):58-61. (in Chinese)
［5］余文力, 董三强, 朱满林, 等. 导弹战斗部炸药装药的贮存可靠性研究［J］. 空军工程大学学报:自然科学版, 2005, 6(2):43-45.
YU Wen-li, DONG San-qiang, ZHU Man-lin, et al. Research on storage reliability of missile warhead explosive charge［J］. Journal of Air Force Engineering University: Natural Science, 2005, 6(2): 43-45. (in Chinese)
［6］焦东明, 杨月诚, 强洪夫, 等. HTPB固体推进剂增塑剂选取分子模拟研究［J］. 化学研究与应用, 2009, 21(6):805-809.
JIAO Dong-ming, YANG Yue-cheng, QIANG Hong-fu, et al. Research of selecting plasticizer for HTPB solid propellant by molecular dynamics simulation［J］. Chemical Research and Application, 2009, 21(6):805-809. (in Chinese)
［7］张俊, 刘玉存, 张喜亮, 等. 增塑剂类型对浇注 PBX 药浆表观粘度的影响［J］. 火工品, 2017(2):29-32.
ZHANG Jun, LIU Yu-cun, ZHANG Xi-liang, et al. Influences of plasticizer types on the apparent viscosity of casting PBX slurry［J］. Initiators & Pyrotechnics, 2017(2):29-32. (in Chinese)
［8］ Huang Z P, Nie H Y, Zhang Y Y, et al. Migration kinetics and mechanisms of plasticizers, stabilizers at interfaces of NEPE propellant/HTPB liner/EDPM insulation［J］. Journal of Hazardous Materials, 2012, 229/230(3):251-257.
［9］ Zhang W, Jiao Q, Yan S, et al. Influence of purification of energetic binders by vacuum rotary evaporation in different conditions［C］∥20th New Trends in Research of Energetic Materials. Pardubice, Czech: University of Pardubice Press, 2017.

［10］陈春燕, 王晓峰, 高立龙, 等. 固化参数对HTPB固化反应和力学性能的影响［J］. 化学研究与应用, 2013, 25(10):1381-1385.
CHEN Chun-yan, WANG Xiao-feng, GAO Li-long, et al. Effects of NCO/OH molar ratio on the cure reaction and mechanical property of HTPB［J］. Chemical Research and Application, 2013, 25(10):1381-1385. (in Chinese)
［11］ Van Krevelen D W, Hoftyzer P J. Properties of polymers［M］. 3rd ed. Amsterdam, Holland: Elsevier Scientific Publications, 1990: 875.
［12］ Abou-Rachid H, Lussier L S, Ringuette S, et al. On the correlation between miscibility and solubility properties of energetic plasticizers/polymer blends: modeling and simulation studies［J］. Propellants Explosives Pyrotechnics, 2008, 33(4):301-310.
［13］ Small P A. Some factors affecting the solubility of polymers［J］. Journal of Applied Chemistry, 1953, 3(2):71-80.
［14］ Jaidann M, Abou-Rachid H, Lafleur-Lambert X, et al. Modeling and measurement of glass transition temperatures of energetic and inert systems［J］. Polymer Engineering & Science, 2008, 48(6): 1141-1150.
［15］杨雪海, 张伟斌, 杨仍才, 等. 复杂构型PBX截面密度分布CT测试方法［J］. 含能材料, 2016, 24(6):609-613.
YANG Xue-hai, ZHANG Wei-bin, YANG Reng-cai, et al. CT test method for the cross-section density distribution of PBX component with complex configuration［J］. Chinese Journal of Energetic Materials, 2016, 24(6):609-613. (in Chinese)
［16］ Sharma T C, Kumar M, Narang J K, et al. Thermal decomposition and kinetics of plastic bonded explosives based on mixture of HMX and TATB with polymer matrices［J］. Defence Technology, 2017, 13(1):22-32.
［17］殷明, 罗观, 代晓淦, 等. 高固含量HMX基浇注PBX的烤燃试验研究［J］. 火炸药学报, 2014, 37(1):44-48.
YIN Ming, LUO Guan, DAI Xiao-gan, et al. Cook-off test investigation of high solid-content casted PBX based on HMX［J］. Chinese Journal of Explosives & Propellants, 2014, 37(1):44-48. (in Chinese)

第39卷
第1期2018 年1月兵工学报ACTA
ARMAMENTARIIVol.39No.1Jan.2018

[1]	刘纯，欧卓成，段卓平，黄风雷. 动态加载下高聚物粘结炸药中椭圆孔洞坍塌引起的热点温度及其半经验解析表达[J]. 兵工学报, 2022, 43(1): 57-68.
[2]	白志玲，段卓平，黄风雷. 高聚物粘结炸药冲击起爆统计热点反应速率模型[J]. 兵工学报, 2021, 42(11): 2379-2387.
[3]	秦金凤，赵雪，钱华，芮久后. 高致密球形黑索今晶体结构对高聚物粘结炸药安全性能的影响[J]. 兵工学报, 2020, 41(3): 481-487.
[4]	魏强，黄西成，陈刚，陈鹏万. 高聚物粘结炸药动态损伤破坏的数值刻画[J]. 兵工学报, 2019, 40(7): 1381-1389.
[5]	李潘，郝志明，刘永平，甄文强. 基于近场动力学非普通状态理论的高聚物粘结炸药损伤破坏模拟研究[J]. 兵工学报, 2018, 39(5): 893-900.
[6]	王竟成，罗景润. 不同细观力学方法预测高聚物粘结炸药有效模量的比较[J]. 兵工学报, 2017, 38(6): 1106-1112.
[7]	崔云霄，陈鹏万，郭保桥， David A. Cendón，周忠彬. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态断裂行为研究[J]. 兵工学报, 2017, 38(12): 2379-2385.
[8]	崔云霄，陈鹏万， David A. Cendón，戴开达，钟方平. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态巴西实验的数值模拟[J]. 兵工学报, 2016, 37(9): 1639-1645.
[9]	白志玲，段卓平，景莉，刘益儒，欧卓成，黄风雷. 飞片冲击起爆高能钝感高聚物粘结炸药的实验研究[J]. 兵工学报, 2016, 37(8): 1464-1468.
[10]	唐贤进，张丘，邹刚，吴松，刘维，尹锐. 基于径向基函数神经网络的高聚物粘结炸药切削表面粗糙度预测研究[J]. 兵工学报, 2014, 35(2): 200-206.
[11]	唐维1-3，魏智勇1，黄交虎1，刘维1，刘彤2，章定国3. 高聚物粘结炸药模拟材料的超声振动切削试验研究[J]. 兵工学报, 2013, 34(1): 30-35.
[12]	张丘，黄交虎，尹锐，唐维. 高聚物粘结炸药切削表面的细观形貌与形成机理[J]. 兵工学报, 2010, 31(10): 1337-1340.