基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析

doi:10.3969/j.issn.1000-1093.2017.04.010

兵工学报 ›› 2017, Vol. 38 ›› Issue (4): 695-703.doi: 10.3969/j.issn.1000-1093.2017.04.010

基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析

陈富华¹，胡小秋¹，刘志涛²

（1.南京理工大学机械工程学院，江苏南京 210094； 2.南京理工大学化工学院，江苏南京 210094）

收稿日期:2016-07-12 修回日期:2016-07-12 上线日期:2017-06-06
通讯作者: 胡小秋(1963—),男，副教授，硕士生导师 E-mail:hu106106@yahoo.com.cn
作者简介:陈富华(1991—),男，硕士研究生。E-mail: chenfuhua4931@163.com
基金资助:
国家自然科学基金项目（51506093）

Workbench-based Simulation Analysis of Multi-perforated Gun Propellant in Extrusion Process

CHEN Fu-hua¹， HU Xiao-qiu¹， LIU Zhi-tao²

(1.School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China；2.School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China)

Received:2016-07-12 Revised:2016-07-12 Online:2017-06-06

摘要/Abstract

摘要： 为了获得特定多孔发射药模具的合理结构参数，应用Workbench软件的流体与固体耦合模块模拟了发射药药料在模腔内的挤压过程及针架的变形。采用单因素法分析了收缩角、成型段长度对挤出成型压力和模具针架系统变形的影响。结果表明：随着成型段长度的加大，压力逐渐增大、挤压药密实性增加、针架系统变形增大；随着收缩角的加大，压力增大、挤压药密实性增加、针架系统变形逐渐减小，在多孔模腔收缩角55°之后，压力增大、变形减小的幅度平缓；收缩段和成型段截面压力差从入口至出口逐渐减小，最后达到均匀分布。

关键词: 兵器科学与技术, 发射药, Workbench软件, 多孔发射药模具, 挤压, 截面

Abstract: In order to obtain the structural parameters of specific multi-perforated gun propellant mould, the fluid-solid coupling module of Workbench is used to simulate the extrusion process of gun propellant slurry in the mold cavity and the deformation process of needle holder. The influences of shrinkage angle and length of molding on the extrusion molding pressure and the deformation of needle holder system are analyzed by the single factor method. The result shows that the compactness of extruded propellant and the deformation of needle holder system increase with the increase in length of forming segment and pressure. With an increase in contraction angle, the pressure and compactness of extruded propellant increase, but the deformation of needle holder system decreases gradually. At more than 55°, the pressure amplitude increases and the amplitude of the system deformation decreases. The pressure difference between the contracting segment and the forming segment is gradually reducedfrom the inlet to the outlet, and the final pressure distribution is uniform. Key

Key words: ordnancescienceandtechnology, propellant, Workbenchsoftware, multi-perforatedgunpropellantmould, extrusion, section

中图分类号:

TQ560.6

陈富华，胡小秋，刘志涛. 基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析[J]. 兵工学报, 2017, 38(4): 695-703.

CHEN Fu-hua， HU Xiao-qiu， LIU Zhi-tao. Workbench-based Simulation Analysis of Multi-perforated Gun Propellant in Extrusion Process[J]. Acta Armamentarii, 2017, 38(4): 695-703.

参考文献

［1］王泽山,欧育湘,任务正. 火炸药科学技术［M］. 北京: 北京理工大学出版社, 2002.
WANG Ze-shan, OU Yu-xiang, REN Wu-zheng. Explosive science and technology［M］. Beijing: Beijing Institute of Technology Press, 2002. (in Chinese)
［2］ Kalaycioglu B, Dirikolu M H, elik V. An elasto-viscoplastic analysis of direct extrusion of a double base solid propellant［J］. Advances in Engineering Software, 2010, 41(9):1110-1114.
［3］ Zhong T, Rao G, Peng J. Numerical simulation of three dimensional fpPropellant［J］. Procedia Engineering, 2014, 84:920-926.
［4］丁亚军, 应三九.螺杆挤出过程中物料在线流变行为及其数值模拟［J］. 兵工学报, 2015, 36(8): 437-1442.
DING Ya-jun, YING San-jiu. In-line rheological behaviors and numerical simulation of material in extrusion processing［J］. Acta Armamentarii, 2015, 36(8): 1437-1442. (in Chinese)
［5］张丹丹,何卫东. 硝基胍七孔发射药挤压成型过程的数值模拟［J］. 火炸药学报, 2015, 38(1): 82-86.
ZHNAG Dan-dan，HE Wei-dong. Numerical simulation of 7-hole nitroguanidine-based gun propellant in extrusion forming process［J］. Chinese Journal of Explosives and Propellant, 2015, 38(1): 82-86. (in Chinese)
［6］刘林林,马忠亮,高可政,等. 变燃速发射药挤出过程中药料流动计算研究［J］. 含能材料, 2010, 18(5): 583-586.
LIU Lin-lin, MA Zhong-liang, GAO Ke-zheng, et al. Computational study of flow for outside layer of variable burning rate propellant during extrusion［J］. Chinese Journal of Energetic Materials, 2010, 18(5): 583-586. (in Chinese)
［7］柴峻,马忠亮.七孔变燃速发射药挤出胀大的模拟［J］. 四川兵工学报, 2015, 36(4): 124-126.
CHAI Jun, MA Zhong-liang. Extrusion swelling numerical simulation of co-extrusion process of variable-burning rate propellant［J］. Journal of Sichuan Ordnance, 2015, 36(4): 124-126. (in Chinese)
［8］季丹丹,刘志涛，廖昕,等.19孔发射药挤出过程的数值模拟与模具优化［J］.含能材料,2016,24(11):1114-1120.
JI Dan-dan, LIU Zhi-tao, LIAO Xin, et al. Numerical simulation of extrusion process and die optimization for 19-hole propellant［J］.Chinese Journal of Energetic Materials, 2016,24(11):1114-1120. (in Chinese)
［9］ Yu Y, Wang J, Gong Y G, et al. The finite analysis and optimization of head runner of rubber sheeting extruder［J］. Key Engineering Materials, 2013, 561:25-29.

［10］韩博. 高增面性大弧厚硝基胍发射药工艺技术研究［D］. 南京:南京理工大学,2009.
HAN Bo. Studies on process technology of high progressive and large arc-thickness NQ-based gun propellant［D］. Nanjing: Nanjing University of Science and Technology, 2009. (in Chinese)
［11］王琼林.钝感发射药技术研究［D］.南京：南京理工大学，1991.
WANG Qiong-lin. Study on the technology of deterred gun propellant［D］. Nanjing: Nanjing University of Science and Technology, 1991. (in Chinese)

第38卷
第4期2017 年4月兵工学报ACTA
ARMAMENTARIIVol.38No.4Apr.2017

[1]	王钰婷, 黄正祥, 祖旭东, 马彬, 肖强强, 贾鑫. 等腰梯形截面聚能装药射流成型及侵彻特性[J]. 兵工学报, 2022, 43(4): 748-757.
[2]	周梦蕾，南风强，何卫东，王沫茹，堵平，王彬彬. 挤出沉积3D打印工艺参数对发射药尺寸及拉伸强度的影响[J]. 兵工学报, 2022, 43(3): 661-666.
[3]	梁昊，丁亚军，李世影，赵先正，肖忠良. 钝感双基发射药迁移失效评价方法[J]. 兵工学报, 2022, 43(2): 297-304.
[4]	俞青源，王文俊，孙美玲，唐方圆，赵静，邵自强. 纳米纤维素制备及其在硝化棉基发射药中的应用[J]. 兵工学报, 2021, 42(5): 955-960.
[5]	姜冬冬，薛晓春. 整装式液体发射药燃烧推进过程的内弹道特性[J]. 兵工学报, 2021, 42(4): 755-763.
[6]	刘计划，赵宏立，何昌辉，靳建伟，张邹邹，王琼林，赵宝明. 冲击载荷作用下典型发射药的弹性模量分析方法[J]. 兵工学报, 2021, 42(2): 289-296.
[7]	孙明亮，陆林，刘宁，张相炎. 液体发射药迫击炮内弹道燃烧稳定性[J]. 兵工学报, 2020, 41(11): 2145-2154.
[8]	李世影，丁亚军，梁昊，赵先正，肖忠良，李纯志，贺云. 梯度硝基发射药的设计原理与实现方法[J]. 兵工学报, 2020, 41(11): 2198-2205.
[9]	于哲峰，陈旭明，杨鹰，部绍清，谢爱民，黄洁，柳森. 高超声速飞行器尾迹转捩及其对雷达散射截面的影响[J]. 兵工学报, 2019, 40(12): 2467-2472.
[10]	宋鹏飞，董新龙，付应乾，索涛. 基于等径通道挤压法的超细晶铜动态剪切变形行为实验研究[J]. 兵工学报, 2018, 39(4): 763-771.
[11]	娄伟鹏，郑长松，李和言，陈建文，张周立，马源. 高速《Symbol》v湿式换挡离合器排油阀临界开启和关闭压力研究[J]. 兵工学报, 2017, 38(9): 1665-1672.
[12]	王宪成，杨绍卿，马宁，赵文柱. 车辆柴油机缸套动载荷磨损计算模型研究[J]. 兵工学报, 2017, 38(9): 1673-1680.
[13]	孙皓泽，常天庆，王全东，孔德鹏，戴文君. 一种基于分层多尺度卷积特征提取的坦克装甲目标图像检测方法[J]. 兵工学报, 2017, 38(9): 1681-1691.
[14]	张玉燕，孙莎莎，王振春，曹海要，战再吉. 高速载流电枢表面瞬态温度场仿真与测量[J]. 兵工学报, 2017, 38(9): 1692-1698.
[15]	李臣明，宦超，石怀龙. 某箱式火箭炮对面目标分布式杀伤最优火力分配[J]. 兵工学报, 2017, 38(9): 1699-1704.

基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析

Workbench-based Simulation Analysis of Multi-perforated Gun Propellant in Extrusion Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价