冲击载荷作用下典型发射药的弹性模量分析方法

doi:10.3969/j.issn.1000-1093.2021.02.007

摘要/Abstract

摘要： 为获得冲击载荷作用下典型发射药弹性模量有效分析方法，进行了落锤冲击发射药的实验研究。结合高速摄像技术和数字图像相关方法，得出发射药在落锤冲击过程中的应力与应变曲线；以此为基础，采取线弹性、非线性弹性和黏弹性3种分析手段，得到DAGR125-21/19发射药在常温和低温下弹性模量随着冲击速度和冲击能量的变化规律。结果表明：随着冲击速度增加，发射药在常温和低温下弹性模量变化较小，其中黏弹性分析得到的弹性模量最小，线弹性和非线性弹性分析的结果相近，且低温下弹性模量远大于常温下弹性模量；通过对双芳-3双基发射药弹性模量的研究，可以得到相似的结论，且常温下双芳-3双基发射药弹性模量与DAGR125-21/19发射药弹性模量相当，但低温下前者远大于后者；基于数字图像相关方法的黏弹性分析，可以获得准确可靠的发射药弹性模量。

关键词: 发射药, 落锤冲击, 弹性模量, 数字图像相关方法

Abstract: The experimental research on drop hammer impacting of gun-propellant was made to obtain an effective analysis method for the elastic modulus of typical gun-propellant under impact loading. The stress and strain curves of gun-propellant during drop hammer impact test were obtained through high-speed photography and digital image correlation method. On this basis, the linear-elastic, nonlinear-elastic and viscoelastic analysis methods are used to get the change laws of elastic modulus of DAGR125-21/19 with impact energy and velocity at normal and low temperatures. The results show that the elastic modulus of gun-propellant changes slightly at normal and low temperatures with the increase in the impact velocity. Furthermore, the magnitude of elastic modulus from viscoelastic analysis is least, the results from linear elastic analysis are close to those from nonlinear elastic analysis, and the elastic modulus of gun-propellant at low temperature is much greater than that at normal temperature. The elastic modulus of SF-3 double-base gun-propellant was studied. It is found that the elastic modulus of SF-3 double-base gun-propellant is equivalent to that of DAGR125-21/19 at normal temperature, but the elastic modulus of the former is much bigger than that of the latter at low temperature. The reliable and accurate elastic modulus of gun-propellant can be derived by using viscoelastic analysis based on digital image correlation method.

Key words: gun-propellant, dropweightimpacttesting, elasticmodulus, digitalimagecorrelation

中图分类号:

O343.5
TJ55

刘计划，赵宏立，何昌辉，靳建伟，张邹邹，王琼林，赵宝明. 冲击载荷作用下典型发射药的弹性模量分析方法[J]. 兵工学报, 2021, 42(2): 289-296.

LIU Jihua， ZHAO Hongli， HE Changhui， JIN Jianwei， ZHANG Zouzou, WANG Qionglin, ZHAO Baoming. Analysis Method for Elastic Modulus of Typical Gun-propellant under Impact Loading[J]. Acta Armamentarii, 2021, 42(2): 289-296.

参考文献

［1］ LIEB R J. Correlation of the failure modulus to fracture-generate surface area in uniaxially compressed M43 gun propellant [R]. Aberdeen Proving Ground, MD,US: Army Research Laboratory, 1995.
[2] 芮筱亭, 冯宾宾, 王国平. 发射装药发射安全性评估方法[J]. 兵工自动化, 2011, 30(5): 56-60.
RUI X T, FENG B B, WANG G P. Evaluation method of launch safety of propellant charge [J]. Ordnance Industry Automation, 2011, 30(5): 56-60.(in Chinese)
[3] 王永强, 杨慧群, 韩进朝. 改善发射药力学性能方法研究进展[J]. 化工新型材料, 2019, 47(7): 50-59.
WANG Y Q, YANG H Q, HAN J C. Study progress in method for improving the mechanical property of gun propellant [J]. New Chemical Materials, 2019, 47(7): 50-59.(in Chinese)
[4] 杨均匀, 袁亚雄, 张小兵. 发射药破碎对火炮射击安全性影响的研究综述[J]. 弹道学报, 1999, 11(4): 92-96.
YANG J Y, YUAN Y X, ZHANG X B. Research survey of the effect of grain fracture on the fire safety in solid propellant gun [J]. Journal of Ballistics, 1999, 11(4): 92-96.(in Chinese)
[5] 徐劲祥. 发射装药挤压破碎对燃烧规律的影响[J]. 火炸药学报, 2007, 30(3):69-71.
XU J X. Effect of extrusion and fracture of gun propellant charge on combustion behavior[J]. Chinese Journal of Explosives and Propellants, 2007, 30(3):69-71.(in Chinese)
[6] 陈涛, 芮筱亭, 贠来峰, 等. 发射药床动态挤压破碎模拟研究[J]. 南京理工大学学报, 2006, 30(4):467-471.
CHEN T, RUI X T, YUN L F, et al. Dynamic extrusion and fracture simulation of propellant charge bed [J]. Journal of Nanjing University of Science and Technology, 2006, 30(4):467-471.(in Chinese)
[7] 姜世平, 黎超. 火炮发射药床冲击破碎动力学仿真研究[J]. 弹道学报, 2019, 31(3):41-45.
JIANG S P, LI C. Dynamic simulation of fragmentation of gun propellant bed under impact load [J]. Journal of Ballistics, 2019, 31(3):41-45.(in Chinese)
[8] 姜世平, 芮筱亭, 洪俊, 等. 发射药床冲击破碎过程的数值模拟 [J]. 固体力学学报, 2011, 32(4):419-425.
JIANG S P, RUI X T, HONG J, et al. Simulation of fragmentation process of propellant ben under impact load [J]. Chinese Journal of Solid Mechanics, 2011, 32(4):419-425.(in Chinese)
[9] 洪俊, 芮筱亭. 发射药粒冲击破碎动力学仿真[J]. 弹道学报, 2010, 22(1):61-64.
HONG J, RUI X T. Dynamic simulation for impact and fracture of propellant grain [J]. Journal of Ballistics, 2010, 22(1):61-64.(in Chinese)
[10] 韩屹湛. 多孔发射药力学特性实验研究与数值仿真[D]. 南京：南京理工大学，2016.
HAN Y Z.Experimental study and numerical simulation on the mechanics characteristic of multi-perforated propellant [D]. Nanjing:Nanjing University of Science and Technology， 2016.(in Chinese)
[11] PAN B, QIAN K M, XIE H M, et al. Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review [J]. Measurement Science and Technology, 2009, 20（6）:062001.
[12] HILD F, ROUX S. Digital image correlation: from displacement measurement to identification of elastic properties - a review [J]. Strain, 2006, 42(2):69-80.
[13] 段淇元, 宫文然, 郭保桥, 等. 高温数字图像相关方法中的制斑和图像处理技术[J]. 清华大学学报（自然科学版）, 2019, 59(6): 425-431.
DUAN Q Y, GONG W R, GUO B Q, et al. Techniques of speckle fabrication and image processing for high temperature digital image correlation [J]. Journal of Tsinghua University (Science and Technology), 2019, 59(6): 425-431.(in Chinese)
[14] 易亚楠, 张小娟, 马少鹏, 等. 基于数字图像相关方法的核石墨力学参数测量[J]. 核动力工程, 2019, 40(3):61-65.
YI Y N, ZHANG X J, MA S P, et al. Parameters measurement of nuclear graphite based on digital image correlation [J]. Nuclear Power Engineering, 2019, 40(3): 61-65.(in Chinese)
[15] 王礼立, PLUVINAGE G, LABIBES K. 冲击载荷下高聚物动态本构关系对粘弹性波传播特性的影响[J]. 宁波大学学报, 1995, 18(3):30-57.
WANG L L, PLUVINAGE G, LABIBES K. The influence of dynamic constitutive relations of polymers at impact loading on the viscoelastic wave propagation character [J]. Journal of Ningbo University, 1995, 18(3):30-57.(in Chinese)
[16] 施绍裘, 喻炳, 王礼立. PP/PA共混高聚物在高应变率下的热粘弹性本构关系和时温等效性[J]. 爆炸与冲击, 2007, 27(3):210-216.
SHI S Q, YU B, WANG L L. Thermoviscoelastic constitutive equation of PP/PA blends and its rate-temperature equivalence relation at high strain rates [J]. Explosion and Shock Waves, 2007, 27(3):210-216.(in Chinese)

第42卷第2期2021 年2月
兵工学报ACTA ARMAMENTARII
Vol.42No.2Feb. 2021

[1]	崔立宝, 杨钊, 丁亚军, 周杰, 肖忠良. 聚多巴胺包覆四孔发射药的结构与性能[J]. 兵工学报, 2023, 44(7): 2014-2022.
[2]	杨硕, 杜天玮, 张晓鹏, 马梁, 张桂昌. 外物损伤对叶片振动疲劳裂纹扩展性能的影响[J]. 兵工学报, 2023, 44(6): 1713-1721.
[3]	周梦蕾，南风强，何卫东，王沫茹，堵平，王彬彬. 挤出沉积3D打印工艺参数对发射药尺寸及拉伸强度的影响[J]. 兵工学报, 2022, 43(3): 661-666.
[4]	梁昊，丁亚军，李世影，赵先正，肖忠良. 钝感双基发射药迁移失效评价方法[J]. 兵工学报, 2022, 43(2): 297-304.
[5]	李居影，李莹，王荣惠，魏化震，孔国强. 2.5维编织复合材料经向拉伸弹性性能预测[J]. 兵工学报, 2021, 42(7): 1516-1523.
[6]	俞青源，王文俊，孙美玲，唐方圆，赵静，邵自强. 纳米纤维素制备及其在硝化棉基发射药中的应用[J]. 兵工学报, 2021, 42(5): 955-960.
[7]	姜冬冬，薛晓春. 整装式液体发射药燃烧推进过程的内弹道特性[J]. 兵工学报, 2021, 42(4): 755-763.
[8]	孙明亮，陆林，刘宁，张相炎. 液体发射药迫击炮内弹道燃烧稳定性[J]. 兵工学报, 2020, 41(11): 2145-2154.
[9]	李世影，丁亚军，梁昊，赵先正，肖忠良，李纯志，贺云. 梯度硝基发射药的设计原理与实现方法[J]. 兵工学报, 2020, 41(11): 2198-2205.
[10]	周俊杰, 苑士华，荆崇波. 考虑空化效应的齿轮泵流量特性研究[J]. 兵工学报, 2020, 41(1): 189-195.
[11]	刘坚成，张雷雷，徐坤，皮爱国，史文卿，黄风雷. 反弹道非正侵彻的弹体结构响应实验研究[J]. 兵工学报, 2019, 40(9): 1797-1803.
[12]	卫水爱，白春华，李春光. 发射药生产过程中静电锥体放电规律数值模拟研究[J]. 兵工学报, 2017, 38(5): 892-899.
[13]	陈富华，胡小秋，刘志涛. 基于有限元分析Workbench软件的多孔发射药挤压过程仿真分析[J]. 兵工学报, 2017, 38(4): 695-703.
[14]	崔云霄，陈鹏万，郭保桥， David A. Cendón，周忠彬. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态断裂行为研究[J]. 兵工学报, 2017, 38(12): 2379-2385.
[15]	刘坚成，皮爱国，黄风雷. 反弹道斜撞击下自由梁结构响应研究[J]. 兵工学报, 2017, 38(11): 2117-2125.