Simulation for Cutting Force of Orthogonal Turn-milling

doi:10.3969/j.issn.1000-1093.2012.04.007

Abstract

Abstract: Aimed at the characteristics of variable cutting depth and thickness in the orthogonal turn-milling process, the theoretical model of cutting force is founded by using mathematic method based on the machining principle, and the change rules of cutting forces with the rotation angles of cutter were simulated in the conditions with and without eccentricity, respectively. The simulation results show that, with the increase of feed rate and eccentricity, the cutting force increases in the same cutting parameters and it is bigger in eccentricity than that in non-eccentricity. Therefore, the theoretical cutting force model provides reference for the research on orthogonal turn-milling mechanism.

Key words: cutting tool technology, orthogonal turn-milling, cutting force, eccentricity, modeling

CLC Number:

TP391

ZHU Li-da, YU Tian-biao, WANG Wan-shan. Simulation for Cutting Force of Orthogonal Turn-milling[J]. Acta Armamentarii, 2012, 33(4): 419-424.

References

［1］ Schulz H, Kneisel T. Turn-milling of hardened steel-an alternative to turning [J]. Annals of CIRP, 1994, 39(1): 93-96.
［2］ Savas V, Ozay C. Analysis of the surface roughness of tangential turn-milling for machining with end milling cutter[J]. Journal of Materials Processing Technology, 2007,186:279-283.
［3］ Choudhury S K, Bajpai J B. Investigation in orthogonal turn-milling towards better surface finish [J]. Journal of Materials Processing Technology, 2005,170 : 487-493.
［4］ Savas V, Ozay C. The optimization of the surface roughness in the

process of tangential turn-milling using genetic algorithm[J]. In J Adv Manufacture Technology, 2008, 37: 335-340.
［5］姜增辉，贾春德. 无偏心正交车铣理论切削力[J]，机械工程学报，2006, 42(9):23-27.
JIANG Zeng-hui, JIA Chun-de. Theoretical cutting force of non-eccentricity orthogonal turn-milling[J]. Chinese Journal of Mechanical Engineering, 2006, 42(9):23-27. (in Chinese)
［6］姜增辉，贾春德. 轴向车铣理论切削力的研究[J].机械工程学报，2005，41(9)， 86-90.
JIANG Zeng-hui,JIA Chun-de. Research on the theoretical cutting force of the axial turn-milling[J]. Chinese Journal of Mechanical Engineering, 2005,41(9),86-90. (in Chinese)
［7］周敏, 张之敬. 微小型正交车铣单齿圆周刃理论切削力研究[J].中国机械工程,2009, 20(13),1527-1532.
ZHOU Min,ZHANG Zhi-jing. Cutting force of single circumference edge for micro orthogonal turn-milling[J]. China Mechanical Engineering, 2009, 20(13),1527-1532 (in Chinese)
［8］ Skoric S, Udiljak T, Ciglar D. Study of the suitability of the machining of rotating surfaces[J]. Transactions of Famena, 2008,32(2): 69-83.
［9］ Pogacink M, Kopac J. Dynamic stabilization of the turn-milling process by parameter optimization[J]. Proc Instn Mech Engrs, 2000, 214:127-135.
［10］ Altintas Y. Manufacturing automation: principles of mental cutting and machine tool vibrations[M]. UK:Cambridge University Press, 2000.

[1]	DENG Hui, ZHANG Zhihong, YI Wenbin, WANG Erli. Modeling Method and Key Characteristics of Submarine Hydrodynamic Pressure Field in Bounded Flow Field [J]. Acta Armamentarii, 2024, 45(2): 527-540.
[2]	DING Yanchao, WANG Baoshou, WU Wenting, LIU Xinhui, TONG Xin. Modeling of Interior Trajectory of Water-driven Underwater Launch Device with Two-stage Piston [J]. Acta Armamentarii, 2024, 45(2): 594-605.
[3]	ZHANG Tianyi, ZHENG Ying, QIU Xinguo, JI Xingjian, JIN Xiaohang. Disturbance Compensation Strategy for Fifth-order Joint Servomechanism Based on Characteristic Model [J]. Acta Armamentarii, 2024, 45(1): 276-287.
[4]	ZHOU Yue, LI Zhuangzhuang, ZHENG Ranshun, LI Jun. Research on Safe Separation Mechanism of UAV Rocket Booster [J]. Acta Armamentarii, 2024, 45(1): 219-230.
[5]	SUN Hao, SUN Qinglin, SUN Mingwei, CHEN Zengqiang. Parafoil-based UAV Recovery System Under Random Initial Conditions [J]. Acta Armamentarii, 2023, 44(3): 718-727.
[6]	DU Kai, JIAO Li, YAN Pei, YU Jianhang, WANG Yubin, QIU Tianyang, WANG Xibin. Study of the Hard Turning Processability of Hardened Ultra-high Strength Steel 45CrNiMoVA [J]. Acta Armamentarii, 2023, 44(3): 773-782.
[7]	QIAO Yang, ZHAO Zhicheng, XIE Jing, CHEN Pengwan. In-plane Compressive Mechanical Behavior of SLM Titanium Alloy Honeycomb Structure [J]. Acta Armamentarii, 2023, 44(3): 629-637.
[8]	GUAN Haijie, WANG Boyang, WANG Xurui, LIU Hai’ou, CHEN Huiyan. A Review on the Development of Military Unmanned Ground System with Mission Payload [J]. Acta Armamentarii, 2023, 44(11): 3333-3344.
[9]	ZHANG Qi, GE Yuxue, LI Pan, KANG Qijun, PEI Yang. Evaluation Method for SoS Contribution Rate of All-optical UAV Swarm Based on ABMS [J]. Acta Armamentarii, 2023, 44(11): 3422-3435.
[10]	CHEN Jianwei, YU Chuanqiang, LIU Zhihao, TANG Shengjin, ZHANG Zhihao, SHU Hongbin. Data Modeling of Multi-Axle Special Vehicles and Lateral Dynamics Applications [J]. Acta Armamentarii, 2023, 44(1): 165-175.
[11]	SHUAI Zhibin, HE Shuai, LI Guohui, LI Yaoheng, LI Yong, ZHANG Ying, JIAN Hongchao. Modeling and Optimal Control of Low-Temperature Starting Process of Electro-Mechanical Transmission for Special Tracked Vehicles [J]. Acta Armamentarii, 2023, 44(1): 117-128.
[12]	YANG Zhanhua， LIU Chunsheng， LI Jun， GUO Shaopeng， LI Jianyang. Dynamic Modeling and Simulation of Airborne Vehicle's Landing Buffer Process [J]. Acta Armamentarii, 2022, 43(S1): 26-34.
[13]	SONG Yu， ZOU Ruping， WANG Jun. On the Practice of Model-based System Engineering in Missile Development [J]. Acta Armamentarii, 2022, 43(S1): 97-106.
[14]	LIU Zunfei， ZOU Bo， CHEN Xulin， ZHANG Wenjuan， YE Shuangping， PAN Jiangli. Architecture Modeling and Effectiveness Evaluation of Equipment System under Manned and Unmanned Joint Operation Mode [J]. Acta Armamentarii, 2022, 43(S1): 155-161.
[15]	SUN Chenfeng, L Weimin, CONG Linhu, XU Pengbo. Reliability Modelling of Hybrid Redundancy System Based on Generalized Stochastic Petri Nets [J]. Acta Armamentarii, 2022, 43(8): 2007-2016.