弹头冲击形状记忆合金悬臂梁实验的数值模拟

兵工学报 ›› 2010, Vol. 31 ›› Issue (4): 491-498.

弹头冲击形状记忆合金悬臂梁实验的数值模拟

张兴华，唐志平，郑航

(中国科学技术大学中国科学院材料力学行为和设计重点实验室，安徽合肥 230027)

收稿日期:2009-06-05 修回日期:2009-06-05 上线日期:2014-05-04
通讯作者: 张兴华 E-mail:zxhst@mail.ustc.edu.cn
作者简介:张兴华(1980—)，男，博士后
基金资助:
国家自然科学基金项目（10672158）

Numerical Simulation of the Experiment on a Shape Memory Alloy Cantilever Impacted by a Bullet

ZHANG Xing-hua， TANG Zhi-ping， ZHENG Hang

(Key Lab for Mechanical Behavior and Design of Materials, Chinese Academy of Sciences, University of Science andna)

Received:2009-06-05 Revised:2009-06-05 Online:2014-05-04
Contact: ZHANG Xing-hua E-mail:zxhst@mail.ustc.edu.cn

摘要/Abstract

摘要： 借助有限元软件ANSYS-LSDYNA，对弹头冲击伪弹性TiNi形状记忆合金(SMA)悬臂梁的实验进借助有限元软件ANSYS-LSDYNA，对弹头冲击伪弹性TiNi形状记忆合金(SMA)悬臂梁的实验进行了数值模拟研究。结果表明，计算所采用的SMA本构抓住了梁冲击响应的主要特征，较好地再现了实验中高速摄影机记录到的梁的运动过程以及应变片测得的波形；根据计算结果揭示了相变弯曲波的传播以及与自由端反射波相互作用的过程中相变区的时空演化规律，分析了相变铰的可回复与有限性两个特性及其对结构响应的影响，并提出了TiNi梁能量耗散的机制。

关键词: 爆炸力学, 冲击相变, 形状记忆合金, 相变铰, 弯曲波

Abstract: A numerical simulation of the experiment on a TiNi shape memory alloy (SMA ) cantilever at the pseudo elastic state impacted by a bullet was investigated by using the FEA software ANSYS-LSDYNA. The result showed that the SMA model adopted in the simulation captured the main characteristic of the cantilever impact response. The simulation reproduced well the movement and deformation of the cantilever and the wave profile in the experiment which were recorded by the high speed camera and measured by the strain gauges respectively. On the basis of the comparison between simulation and experiment, the impact response of the SMA cantilever was revealed in detail. Firstly, the spatio-temporal evolution regularity of the transformation zones was revealed when the transformation flexural wave propagates and interacts with its reflected wave from the free end. Then the typical recoverable and finite characteristics of a transformation hinge and its effect on the structure response were further analyzed. Finally the energy dissipation mechanism of TiNi cantilever was represented.

Key words: explosion mechanics, shock induced phase transition, shape memory alloy, transformation hinge, flexural wave, energy dissipation

中图分类号:

O358

张兴华，唐志平，郑航. 弹头冲击形状记忆合金悬臂梁实验的数值模拟[J]. 兵工学报, 2010, 31(4): 491-498.

ZHANG Xing-hua， TANG Zhi-ping， ZHENG Hang. Numerical Simulation of the Experiment on a Shape Memory Alloy Cantilever Impacted by a Bullet[J]. Acta Armamentarii, 2010, 31(4): 491-498.

参考文献

［1］ Collet M, Foltete E, Lexcellent C. Analysis of the behavior o
f a shape memory alloy beam under dynamical loading［J］. European Journal of Me
chanics, A/Solids, 2001, 20(4): 615-630.
［2］ Nemat-Nasser S, Choi J Y, Isaacs J B, et al. Experimental observatio
n of high-rate buckling of thin cylindrical shape-memory shells［C］∥Smart St
ructures and Materials 2005: Active Materials: Behavior and Mechanics. US: SPIE,
2005, 5761: 347-354.
［3］ Hashemi S M T, Khadem S E. Modeling and analysis of the vibration beh
avior of a shape memory alloy beam［J］. International Journal of Mechanical Sci
ences, 2006, 48: 44-52.
［4］ Li D, Tang Z P, Zhang X H. Dynamic buckling of superelastic SMA shell
s under axial impact-numerical simulation［C］∥Proceedings of the the 7th inte
rnational conference on shock and impact loads on structures. Beijing: Beijing I
nstitute of Technology, 2007: 335-342.
［5］唐志平，卢艰春，张兴华. TiNi相变悬臂梁的横向冲击特性实验研究［J］.
爆炸与冲击,2007, 27(4):289-295.
TANG Zhi-ping, LU Jian-chun, ZHANG Xing-hua. Experimental study of the dynami
c behavior of TiNi cantilever beams with phase transformation subjected to trans
versal impact［J］. Explosion and Shock Waves, 2007, 27(4): 289-295. (in Chinese
)
［6］张兴华，唐志平，李丹，等. 横向冲击载荷下伪弹性TiNi合金矩形悬臂梁结
构响应的实验研究［J］.实验力学，2008, 23(1): 43-52.
ZHANG Xing-hua, TANG Zhi-ping, LI Dan, et al. Experimental study of the dynami
c behavior of TiNi cantilever beams with rectangular cross-section under transv
ersal impact［J］. Journal of Experimental Mechanics, 2008, 23(1): 43-52. (in Ch
inese)
［7］ Auricchio F, Taylor R L. Shape-memory alloys: modelling and numerical si
mulations of the finite-strain superelastic behavior［J］. Computer Methods in
Applied Mechanics and Engineering, 1997, 143: 175-195.
［8］ Auricchio F, Taylor R L, Lubliner J. Shape-memory alloys: macromodelling
and numerical simulations of the superelastic behavior［J］. Computer Methods i
n Applied Mechanics and Engineering, 1997, 146: 281-312.
［9］张兴华. TiNi相变悬臂梁的冲击响应研究［D］. 合肥: 中国科学技术大学,
2007.
ZHANG Xing-hua. Study of impact response of TiNi phase transformation cantileve
r［D］. Hefei: University of Science and Technology of China, 2007. (in Chinese)
［10］ Liew K M, Ren J, Kitipornchai S. Analysis of the pseudoelast
ic behavior of a SMA beam by the element-free Galerkin method［J］. Engineering
Analysis with Boundary Elements, 2004, 28: 497-507.
［11］ Buratti G. Stresses and deflections in a pseudo-elastic beam under
cyclic loads［J］. Continuum Mech Thermodyn, 2005, 17: 149-157.

[1]	冉春，陈鹏万，李玲，张旺峰. 中高应变率条件下TC18钛合金动态力学行为的实验研究[J]. 兵工学报, 2017, 38(9): 1723-1728.
[2]	陈浩玉，洪仁楷，陈永涛，张世文，任国武，莫俊杰. 用于微层裂物质诊断的小型动量探针技术[J]. 兵工学报, 2017, 38(9): 1729-1735.
[3]	唐廷，周健南. 地震后地下受损拱结构的抗爆炸能力研究[J]. 兵工学报, 2017, 38(9): 1736-1744.
[4]	杨军，李焰，张德志，史国凯，张敏，刘文祥，王昭，熊琛. 光子多普勒测速仪与压杆相结合的冲击波反射压力测试技术[J]. 兵工学报, 2017, 38(7): 1368-1374.
[5]	刘俊，田宙，钟巍，谢淑红. 冲击波作用下单层钢化玻璃抗爆性能的数值模拟研究[J]. 兵工学报, 2017, 38(7): 1402-1408.
[6]	李勇，程远胜，张攀，刘均. 空中爆炸载荷下梯度波纹夹层板抗爆性能仿真研究[J]. 兵工学报, 2017, 38(6): 1131-1139.
[7]	赵天辉，高康华，王明洋，李斌，孙松，郭强. 方形容器爆燃泄放过程中的压力特性实验研究[J]. 兵工学报, 2017, 38(4): 722-727.
[8]	崔云霄，陈鹏万，郭保桥， David A. Cendón，周忠彬. 基于内聚裂纹模型的高聚物粘结炸药模拟材料动态断裂行为研究[J]. 兵工学报, 2017, 38(12): 2379-2385.
[9]	刘坚成，皮爱国，黄风雷. 反弹道斜撞击下自由梁结构响应研究[J]. 兵工学报, 2017, 38(11): 2117-2125.
[10]	武强，张庆明，龙仁荣，龚自正. 含能材料防护屏在球形弹丸超高速撞击下的穿孔特性研究[J]. 兵工学报, 2017, 38(11): 2126-2133.
[11]	任国武，郭昭亮，汤铁钢，苏红梅，温上捷，金山. 高应变率加载下金属柱壳断裂的实验研究[J]. 兵工学报, 2016, 37(1): 77-82.
[12]	崔杰，周塞北，王逸，何宝. 减压条件下竖直边界附近气泡动力学行为数值与实验研究[J]. 兵工学报, 2015, 36(9): 1696-1703.
[13]	任鹏，张伟，刘建华，黄威. 高强度水下爆炸等效冲击波加载特性研究[J]. 兵工学报, 2015, 36(4): 716-722.
[14]	刘庆明，刘丽斌，汪建平，王斌，张云明. 烟酸粉尘云爆炸极限的逻辑回归分析[J]. 兵工学报, 2015, 36(3): 523-529.
[15]	项大林，荣吉利，何轩，刘函，陈鹏万，冯志伟. 基于三维数字图像相关方法的水下冲击载荷作用下铝板动力学响应研究[J]. 兵工学报, 2014, 35(8): 1210-1217.