全射弹寿命过程中的大口径机枪自动机磨损和性能衰减趋势研究

doi:10.3969/j.issn.1000-1093.2016.08.003

兵工学报 ›› 2016, Vol. 37 ›› Issue (8): 1359-1364.doi: 10.3969/j.issn.1000-1093.2016.08.003

全射弹寿命过程中的大口径机枪自动机磨损和性能衰减趋势研究

齐玉辉，徐诚

（南京理工大学机械工程学院，江苏南京210094）

收稿日期:2015-06-02 修回日期:2015-06-02 上线日期:2016-09-30
通讯作者: 齐玉辉 E-mail:qinjust@mail.njust.edu.cn
作者简介:齐玉辉(1977—)，男，副研究员，博士研究生
基金资助:
国家自然科学基金项目（51575279）

Research on Wear and Performance Degradation of a Large-caliber Machine Gun Automatic Mechanism in Firing Life-span

QI Yu-hui, XU Cheng

(School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China)

Received:2015-06-02 Revised:2015-06-02 Online:2016-09-30
Contact: QI Yu-hui E-mail:qinjust@mail.njust.edu.cn

摘要/Abstract

摘要： 大口径机枪在全射弹寿命过程中的自动机关键部位磨损和性能衰减情况对机构功能和动作可靠性将产生影响，从而影响武器的使用性能和作战效能。以某型大口径机枪作为试验对象，测量全射弹寿命过程中自动机关键部位磨损情况和自动机性能衰减情况，统计自动机故障。研究结果与分析表明：全射弹寿命过程中的枪机闭锁支撑面磨损量和开闭锁曲线磨损量不大，枪机框导轨磨损量较大；随着射弹量的增加，自动机闭锁力逐渐变小，复进簧逐渐变短，后坐到位速度的均方差变大，自动机动作故障变多；自动机后坐到位速度的均方差增大，自动机动作故障增多与自动机关键部位磨损正相关。建立了闭锁力衰减经验公式、复进簧自由长度衰减经验公式、枪机框导轨磨损经验公式、枪机框后坐到位与复进到位撞击面的磨损经验公式，经验公式计算结果与试验数据吻合较好，可以用于推断该大口径机枪自动机部分性能衰减和磨损情况。

关键词: 兵器科学与技术, 大口径机枪, 自动机, 综合寿命试验, 磨损, 性能衰减

Abstract: The wear of key portion and performance degradation of automatic mechanism have an impact on the mechanism function and action reliability in firing life-span, which leads to an influence on the performance and operational effectiveness of the large-caliber machine gun. A large-caliber machine gun is used as the experimental object. The wear of key portion and performance degradation of automatic mechanism during firing life-span are measured in detail, and the failure statistics of automatic mechanism are completed. Experimental results show that the wear losses of bolt locking supporting surface and locking curve groove during firing are low, but the wear loss of bolt carrier guiderail is high. With the increase in fired shot quantity, the locking force decreases, the length of recoil spring is shortened, the standard deviation of recoil velocity increases, and the moving fault of automatic mechanism increases. There is a positive correlation among the moving fault and standard deviation of recoil velocity and the wear of key portion of automatic mechanism. The empirical models of locking force attenuation and the free length attenuation of recoil spring, and a wear model of bolt carrier guiderail and impact surface when bolt carrier recoils to position and returns to original position are established, respectively. The empirical models are good agreement with the experimental data. These models can be used to estimate the wear and performance degradation of automatic mechanisms.

Key words: ordnance science and technology, large-caliber machine gun, automatic mechanism, longevity experiment, wear, performance degradation

中图分类号:

TJ25

齐玉辉，徐诚. 全射弹寿命过程中的大口径机枪自动机磨损和性能衰减趋势研究[J]. 兵工学报, 2016, 37(8): 1359-1364.

QI Yu-hui, XU Cheng. Research on Wear and Performance Degradation of a Large-caliber Machine Gun Automatic Mechanism in Firing Life-span[J]. Acta Armamentarii, 2016, 37(8): 1359-1364.

参考文献

［1］樊磊, 王亚平, 刘一鸣,等. 超轻量化高射机枪刚柔耦合建模和仿真[J]. 弹道学报, 2009, 21(1):67-70.
FAN Lei, WANG Ya-ping, LIU Yi-ming, et al. Rigid-flex coupled modeling and simulation of a super-light antiaircraft machine gun[J]. Journal of Ballistics, 2009, 21(1):67-70. (in Chinese)
[2］毛庆龙, 申文杰, 沙金龙，等. 机枪自动机抗过载特性研究[J]. 兵工学报, 2013, 34(12):1489-1494.
MAO Qing-long, SHEN Wen-jie, SHA Jin-long, et al. Research on the overload characteristic of the automatic mechanism for machine guns[J]. Acta Armamentarii, 2013, 34(12):1489-1494.(in Chinese)
[3］王瑞林, 李永建, 张国光. 连发武器射频与固有频率匹配关系研究[J]. 兵工学报, 2000, 21(2):105-107.
WANG Rui-lin, LI Yong-jian, ZHANG Guo-guang. Matching of automatic-weapon's firing rate and its inherent frequency[J]. Acta Armamentarii, 2000, 21(2):105-107.(in Chinese)
[4］姚建军, 徐诚. 机枪系统发射动力学研究[J].兵工学报, 2002, 23(3):406-408.
YAO Jian-jun, XU Cheng. A study on the launching dynamics of machine gun system[J]. Acta Armamentarii, 2002, 23(3):406-408. (in Chinese)
[5］樊磊, 刘恩锦, 刘卫明，等. 大口径机枪枪管寿命趋势分析[J]. 弹道学报, 2009, 21(3):39-43.
FAN Lei, LIU En-jin, LIU Wei-ming,et al.Performance decay analysis of a large caliber machine gun barrel in lifetime[J]. Journal of Ballistics, 2009, 21(3):39-43. (in Chinese)
[6］王亚平, 徐诚, 王永娟，等. 火炮与自动武器动力学[M]. 北京:北京理工大学出版社, 2013.
WANG Ya-ping, XU Cheng, WANG Yong-juan, et al. Dynamics of artillery and automatic weapons [M]. Beijing: Beijing Institute of Technology Press, 2013. (in Chinese)
[7］ Zelenko V K, Korolev V M, Drozdov Y N. Correlation between the wearing process of a sniper rifle barrel and bullet structure[J]. Journal of Machinery Manufacture and Reliability, 2010, 39(3):272-275.
[8］邹衍, 徐诚, 张克. 5.8 mm/7.62 mm模块化步枪运动特性匹配分析[J]. 兵工学报, 2015, 36(7):1356-1362.
ZUO Yan, XU Cheng, ZHANG Ke. Analysis of kinetic characteristic matching of 5.8 mm/7.62 mm modularized rifles[J]. Acta Armamentarii, 2015, 36(7):1356-11362.(in Chinese)
[9］刘国庆, 邹衍, 管小荣,等. 新型卧式冲击疲劳试验机性能研究[J]. 南京理工大学学报, 2014,38(3):361-365.
LIU Guo-qing,ZOU Yan,GUAN Xiao-rong, et al. Performance of a new type of horizontal impact fatigue testing machine[J]. Journal of Nanjing University of Science and Technology, 2014, 38(3): 361-365. (in Chinese)
[10］王长庚, 徐万和, 徐诚. 人-枪系统中不同自动方式对枪械后坐作用影响研究[J]. 兵工学报, 2014, 35(5):741-747.
WANG Chang-geng,XU Wan-he, XU Cheng. Research on the influence of different automatic action of gun on its recoil effect in man-gun system[J]. Acta Armamentarii, 2014, 35(5):741-747.(in Chinese)

[1]	秦国华，高杰，叶海潮，姜国杰，黄帅，赖晓春. 基于融合评价指标和神经网络的刀具磨损预测[J]. 兵工学报, 2021, 42(9): 2013-2023.
[2]	李恒, 叶祖坤, 查文彬, 王禹林. 基于多传感器信息决策级融合的刀具磨损在线监测[J]. 兵工学报, 2021, 42(9): 2024-2031.
[3]	沈浩，蔡杰，吕鹏，张从林，李玉新，关庆丰. 激光工艺参数对NiCoCrAlYSi熔覆层微观组织及性能的影响[J]. 兵工学报, 2021, 42(7): 1524-1534.
[4]	郭圣刚，王建平，赵忠诚，程晶晶，田新伟. 金属掺杂对高强化柴油机活塞销类金刚石薄膜涂层摩擦学性能的影响[J]. 兵工学报, 2021, 42(4): 715-722.
[5]	赵屹东, 陈慧岩, 胡家铭. 双侧独立电驱动履带车辆自动机械变速器线控换挡控制方法[J]. 兵工学报, 2021, 42(3): 459-467.
[6]	黄伟，杨黎明，史戈宁，张延松，田开文，刘凯. 电磁发射条件下CuCrZr合金材料轨道损伤行为研究[J]. 兵工学报, 2020, 41(5): 858-864.
[7]	金文奇，宁金贵，王剑，邓波. 基于全膛烧蚀磨损特征的火炮内弹道仿真研究[J]. 兵工学报, 2019, 40(5): 968-977.
[8]	胡春东，董瀚，赵洪山，乔自平，李峻松. 某机枪枪管內膛损伤特征[J]. 兵工学报, 2019, 40(3): 480-487.
[9]	颜丙辉，魏广宁，李晨霞，李雪松. 工艺参数对电沉积钴镍合金镀层成分及耐磨性能的影响[J]. 兵工学报, 2018, 39(4): 753-762.
[10]	任海锋，潘宏侠. 基于多分形特征的枪械自动机裂纹故障诊断[J]. 兵工学报, 2018, 39(3): 457-462.
[11]	饶响，盛晨兴，郭智威. 不同表面纹理结构对柴油机缸套-活塞环摩擦磨损性能的影响研究[J]. 兵工学报, 2018, 39(2): 356-363.
[12]	张利敏，王根全，王延荣，赵志强，张忠伟，宋现浩. 某型柴油机活塞销轴承磨损分析及表面型线设计[J]. 兵工学报, 2018, 39(10): 1892-1900.
[13]	赵丹丹，焦锋. 基于灰色关联分析的35CrMoV钢活塞杆激光熔覆工艺参数优化[J]. 兵工学报, 2018, 39(10): 2073-2080.
[14]	娄伟鹏，郑长松，李和言，陈建文，张周立，马源. 高速《Symbol》v湿式换挡离合器排油阀临界开启和关闭压力研究[J]. 兵工学报, 2017, 38(9): 1665-1672.
[15]	王宪成，杨绍卿，马宁，赵文柱. 车辆柴油机缸套动载荷磨损计算模型研究[J]. 兵工学报, 2017, 38(9): 1673-1680.

全射弹寿命过程中的大口径机枪自动机磨损和性能衰减趋势研究

Research on Wear and Performance Degradation of a Large-caliber Machine Gun Automatic Mechanism in Firing Life-span

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价