电热化学发射中硅堆故障试验分析

doi:10.3969/j.issn.1000-1093.2015.04.001

摘要/Abstract

摘要： 针对电热化学发射试验中脉冲电源发生的高压硅堆损坏，分析可能导致器件损坏的原因，通过机械振动冲击试验、脉冲放电仿真与试验、硅堆反向恢复特性测量等确定故障原因。研究结果表明：电热化学发射过程中的机械振动冲击不会造成硅堆损伤，故障由电感性质负载特性、串联元件的反向恢复特性不一致和脉冲电源非同步放电等因素共同造成，传输线电感分量偏大是故障发生的直接原因。研究结论对于高压硅堆在电热化学发射中的应用具有指导作用。

关键词: 兵器科学与技术, 脉冲电源, 高压硅堆, 电热化学发射, 过电压

Abstract: The silicon stack damage is observed in electrothermal-chemical launch experiment. The details of the possible reasons are analyzed. And the reasons are determined through mechanical vibration impact test, simulation and tests of pulse power supply discharge, and reverse recovery characteristics measurements of silicon stack. Results show that the mechanical vibration shock cannot lead to the silicon stack damage in electrothermal-chemical launch. The silicon stack damage is mainly caused by the cooperation of the reverse recovery characteristics of series components, the inductance characteristic of load and the asynchronous discharge of pulse power supply. The large inductance of the transmission lines is the direct cause for the damage of the silicon stacks in the system.

Key words: ordnance science and technology, pulse power supply, high-voltage silicon stack, electrothermal chemical launch, overvoltage

中图分类号:

TJ303⁺.9

李贞晓，张亚舟，高梁，金涌，栗保明. 电热化学发射中硅堆故障试验分析[J]. 兵工学报, 2015, 36(4): 577-581.

LI Zhen-xiao， ZHANG Ya-zhou， GAO Liang， JIN Yong， LI Bao-ming. Test and Analysis of Silicon Stack Failure in Electrothermal-chemical Launch[J]. Acta Armamentarii, 2015, 36(4): 577-581.

参考文献

［1］李鸿志. 电热发射技术的研究进展[J]. 南京理工大学学报：自然科学版, 2003, 27(5): 449-465.
LI Hong-zhi. Progress in the research of electrothermal chemical launch technology[J]. Journal of Nanjing University of Science and Technology: Natural Science, 2003, 27(5):449-465. (in Chinese)
[2] Yao F L, Li J, Gui Y C, et al. Deve-lopment of 120-mm electro-thermal chemical launcher[J]. IEEE Transactions on Magnetics, 2009, 45(1):377-380.
[3] Ruberg P G,Kumkova I I, Shvetsov G A. New steps in EML research in russia[C]∥2008 14th Symposium on Electromagnetic Launch Technology. Victoria, BC:IEEE, 2008:1-9.
[4] Dyvik J, Herbig J, Appleton R,et al. Recent activities in electrothermal chemical launcher technologies at BEA systems[J]. IEEE Transactions on Magnetics, 2007, 43(1): 303-307.
[5] Weise T H G G, Maag J, Zimmermann G, et al. National overview of the German ETC program[J]. IEEE Transactions on Magnetics, 2003, 39(1):35-37.
[6] Lehmann P. Overview of the electric launcher activities at the French-German Research Institute of Saint-Louis[J]. IEEE Transactions on Magnetics, 2003, 39(1): 24-28.
[7] Liebfried O, Brommer V, Scharnholz S, et al. Refurbishment of a 30 MJ pulsed power supply for pulsed power applications[C]∥2012 16th International Symposium on Electromagnetic Launch Technology(EML).Beijing:IEEE, 2012:1-6.
[8] Rim G H,Cho C H. Protection scheme of a charging and discharging system for a 500 kJ capacitor bank[J]. IEEE Transactions on Magnetics, 2001, 37(1):389-393
[9] Dong J N, Zhang J, Li Jun, et al. The 100-kJ modular pulsed power units for railgun[J]. IEEE Transactions on Plasma Science, 2011, 39(1):304-309.
[10] Fridman B E, Enikeev R Sh, Kowrizhnykh N A, et al. 0.5 MJ 18 kV module of capacitive energy storage[C]∥2009 Pulsed Power Conference. Washington, DC:IEEE, 2009:61-65.
[11] Jin Y S, Lee H S, Kim J S, et al. Novel crowbar circuit for compact 50 kJ capacitor bank[J]. IEEE Transactions on Plasma Science, 2004, 32(2):525-530.
[12] Nunnally W C, Huenefeldt S M, Engel T G. Results from a 750 kJ computer controlled sequentially fired pulse forming network[C]∥Proceedings of 27th International Conference on Power Modulator. Arlington, VA:IEEE, 2006:419-422.
[13] McNab I R, Fish S, Stefani F. Parameters for an electromagnetic naval rail gun[J]. IEEE Transactions on Magnetics, 2001, 37(1): 223-228.
[14] Liu Y, Lin F C, Dai L, et al. Development of a compact 450 kJ pulsed-power-supply system for electromagnetic launcher[J]. IEEE Transactions on Plasma Science, 2011, 39(1): 304-309.
[15] Dai L, Wang Y Z, Zhang Q, et al. Effect of sequence discharge on components in a 600 kJ PPS used for electromagnetic launch system[C]∥2012 16th International Symposium on Electromagnetic Launch Technology (EML). Beijing:IEEE, 2012:1-6.
[16] Kim J S, Choi Y H, Chu J H, et al. Analysis on high surge voltages generated in paralleled capacitor banks[J]. IEEE Transactions on Magnetics, 2003, 39(1):422-426.
[17] 李贞晓, 杨春霞, 栗保明. 高功率脉冲电源中晶闸管应用的研究[J]. 电力电子技术, 2010, 44(10):87-90.
LI Zhen-xiao, YANG Chun-xia, LI Bao-ming. Research on theapplication of thyristor in the pulsed power supply[J]. Power Electronics, 2010, 44(10):87-90. (in Chinese)
[18] 王争论, 成剑, 栗保明. 高压受限电弧等离子体发生器实验研究[J]. 南京理工大学学报:自然科学版, 2003, 27(2): 117-121.
WANG Zheng-lun, CHENG Jian, LI Bao-ming. Experimental study on confined high pressure arc plasma generator[J]. Journal of Nanjing University of Science and Technology:Natural Science, 2003, 27(2):117-121. (in Chinese)
[19] Lee B H, Kim J S, Kim S H, et al. Development of 150 kJ compact pulsed power system for ETC accelerator[C]∥2009 IEEE Pulsed Power Conference. Washington, DC:IEEE, 2009: 66-69.
[20] Shafir N, Zoler D, Wald S, et al. Reliable,highly reproducible plasma injectors for electrothermal and electrothermal-chemical lauchers[J]. IEEE Transactions on Magnetics, 2005, 41(1):355-359.
[21] Yong J, Li B M. Energy skin effect of propellant particles in electrothermal-chemical launcher[J]. IEEE Transactions on Plasma Science, 2013, 41(5):1112-1116.
[22] Lee H S, Jin Y S, Kim J S, et al. Evaluation of a RVU-43 switch as the closing switch for a modular 300 kJ pulse power supply for ETC application[J]. IEEE Transactions on Magnetics, 2001, 37(1):371-374.
[23] Alferov D F, Ivanov V P, Sidorov V A. High-current vacuum triggered switching devices[J]. IEEE Transactions on Magnetics, 2003, 39(1):406-409.

[1]	周伯俊, 于传强，刘志浩，柯冰. 基于高压储能的特种车辆快速起竖技术与验证[J]. 兵工学报, 2022, 43(7): 1488-1497.
[2]	高月光，冯顺山，刘云辉，黄岐. 不同端盖厚度的圆柱形装药壳体破片初速分布[J]. 兵工学报, 2022, 43(7): 1527-1536.
[3]	李贞晓，金涌，杨栋，弯港，栗保明. 一种同轴型脉冲功率电缆的设计与试制[J]. 兵工学报, 2018, 39(8): 1491-1498.
[4]	刘怡，余永刚，莽珊珊. 喷射压力对等离子体射流在液体中扩展的影响[J]. 兵工学报, 2018, 39(12): 2354-2362.
[5]	娄伟鹏，郑长松，李和言，陈建文，张周立，马源. 高速《Symbol》v湿式换挡离合器排油阀临界开启和关闭压力研究[J]. 兵工学报, 2017, 38(9): 1665-1672.
[6]	王宪成，杨绍卿，马宁，赵文柱. 车辆柴油机缸套动载荷磨损计算模型研究[J]. 兵工学报, 2017, 38(9): 1673-1680.
[7]	孙皓泽，常天庆，王全东，孔德鹏，戴文君. 一种基于分层多尺度卷积特征提取的坦克装甲目标图像检测方法[J]. 兵工学报, 2017, 38(9): 1681-1691.
[8]	张玉燕，孙莎莎，王振春，曹海要，战再吉. 高速载流电枢表面瞬态温度场仿真与测量[J]. 兵工学报, 2017, 38(9): 1692-1698.
[9]	李臣明，宦超，石怀龙. 某箱式火箭炮对面目标分布式杀伤最优火力分配[J]. 兵工学报, 2017, 38(9): 1699-1704.
[10]	雷娟棉，张嘉炜，谭朝明. 小攻角下船尾外形对旋转弹丸马格努斯效应影响的数值研究[J]. 兵工学报, 2017, 38(9): 1705-1715.
[11]	李泽，闫晓鹏，栗苹，郝新红，王建涛. 扫频式干扰对调频多普勒引信的干扰机理研究[J]. 兵工学报, 2017, 38(9): 1716-1722.
[12]	张浩为，谢军伟，张昭建，宗彬锋，陈唐军. 基于混合自适应遗传算法的相控阵雷达任务调度[J]. 兵工学报, 2017, 38(9): 1761-1770.
[13]	李茂，侯海量，朱锡，黄晓明，李典，陈长海，胡年明. 结构间隙对芳纶纤维增强复合装甲结构抗侵彻性能的影响[J]. 兵工学报, 2017, 38(9): 1797-1805.
[14]	王鉴, 韩焱, 王黎明, 张丕状, 陈平. 弹丸在膛内运动的回波信号瞬时频率估计方法研究[J]. 兵工学报, 2017, 38(9): 1806-1814.
[15]	刘海鸥，张文胜，徐宜，赵梓烨. 基于核密度估计的履带车辆传动轴载荷谱编制[J]. 兵工学报, 2017, 38(9): 1830-1838.