激光能量密度对激光熔覆NiCoCrAlY涂层组织与性能的影响

doi:10.3969/j.issn.1000-1093.2021.05.021

摘要/Abstract

摘要： 为探究激光熔覆过程中能量密度对NiCoCrAlY涂层组织与性能的影响，在304不锈钢表面制备了NiCoCrAlY涂层。利用X射线衍射仪、扫描电子显微镜分析了NiCoCrAlY涂层的相组成和微观组织。通过显微维氏硬度计和往复摩擦磨损试验机研究了NiCoCrAlY涂层的硬度和耐磨性能。结果表明：NiCoCrAlY涂层气孔数量随激光能量密度增大而减少，熔深和熔高随激光能量密度增大而增大，当激光能量密度为3.8 kJ/cm²时涂层稀释率最低，同时气孔数量较少。NiCoCrAlY涂层中包含γ/γ′相和β相，微观结构以柱状晶为主，随着激光能量密度的增大，β相含量升高，柱状晶变大。不同激光能量密度下NiCoCrAlY涂层硬度均高于基体，当激光能量密度为3.8 kJ/cm²时涂层硬度最高，为301 HV_0.2. 在往复摩擦磨损实验中，当激光能量密度为3.8 kJ/cm²时 NiCoCrAlY涂层摩擦系数最小为0.46，磨损体积最少为0.235 9 mm³，磨损机理主要为磨粒磨损，耐磨性能最好。

关键词: 激光熔覆, NiCoCrAlY涂层, 硬度, 耐磨性

Abstract: NiCoCrAlY coating was prepared on the surface of 304 stainless steel in order to study the effect of energy density on the microstructure and properties of NiCoCrAlY coating during laser cladding. The phase composition and microstructure of NiCoCrAlY coating were analyzed by X-ray diffractometer (XRD) and scanning electron microscope (SEM). The hardness and wear resistance of NiCoCrAlY coating were studied by using a micro Vickers hardness tester and reciprocating friction and wear testing machine. The results show that the number of pores in NiCoCrAlY coating decreases with the increase in laser energy density, and the penetration and melting height increase with the increase in laser energy density. When the laser energy density is 3.8 kJ/cm², the coating dilution rate is the lowest, and the number of pores is less. The NiCoCrAlY coating contains γ/γ′ phase and β phase, and its microstructure is mainly columnar crystals. As the laser energy density increases, β phase content increases and the columnar crystals become larger. The hardness of NiCoCrAlY coating is higher than that of the substrate at different laser energy densities. The coating hardness is the highest when the laser energy density is 3.8 kJ/cm², which is 301 HV_0.2. In the reciprocating friction and wear experiment, when the laser energy density is 3.8 kJ/cm², the friction coefficient is the smallest (0.46) and wear volume is the smallest (0.235 9 mm³), the wear mechanism is mainly abrasive wear, and the wear resistance is the best.

Key words: lasercladding, NiCoCrAlYcoating, hardness, wearresistance

中图分类号:

TG174.44

聂金浩，杨宜鑫，李玉新，张宏建，魏守征，蔡杰，关庆丰. 激光能量密度对激光熔覆NiCoCrAlY涂层组织与性能的影响[J]. 兵工学报, 2021, 42(5): 1083-1091.

NIE Jinhao， YANG Yixin， LI Yuxin， ZHANG Hongjian， WEI Shouzheng， CAI Jie， GUAN Qingfeng. Effect of Laser Energy Density on Microstructure and Properties of Laser Cladding NiCoCrAlY Coating[J]. Acta Armamentarii, 2021, 42(5): 1083-1091.

参考文献

［1］ TOLPYGO V K, CLARKE D R. On the rumpling mechanism in nickel-aluminide coatings: part Ⅰ: an experimental assessment [J]. Acta Materialia, 2004, 52(17): 5115-5127.
[2] 杜伟. 电弧离子镀MCrAlY涂层的组织结构及抗高温氧化性能研究 [D]. 昆明：昆明理工大学, 2018.
DU W. Study on the microstructure and high temperature oxidation resistance of arc ion plating MCrAlY coating [D].Kuming: Kunming University of Science and Technology, 2018. （in Chinese）
[3] GURRAPPA I, SAMBASIVA RAO A. Thermal barrier coatings for enhanced efficiency of gas turbine engines [J]. Surface and Coatings Technology, 2006, 201(6): 3016-3029.
[4] SCHULZ U, LEYENS C, FRITSCHER K, et al. Some recent trends in research and technology of advanced thermal barrier coatings [J]. Aerospace Science and Technology, 2003, 7(1): 73-80.
[5] 贾近, 刘赛月, 孟君晟, 等. 面向高端装备零部件的稀土改性MCrAlY涂层 [J]. 中国表面工程, 2018, 31(5): 54-62.
JIA J, LIU S Y, MENG J S, et al. MCrAlY coating modified by rare earth for high-end equipment parts [J]. China Surface Engineering, 2018, 31(5): 54-62. （in Chinese）
[6] HEJRANI E, SEBOLD D, NOWAK W J, et al. Isothermal and cyclic oxidation behavior of free standing MCrAlY coatings manufactured by high-velocity atmospheric plasma spraying [J]. Surface and Coatings Technology, 2017, 313: 191-201.
[7] FEIZABADI A, SALEHI DOOLABI M, SADRNEZHAAD S K, et al. Cyclic oxidation characteristics of HVOF thermal-sprayed NiCoCrAlY and CoNiCrAlY coatings at 1 000 ℃[J]. Journal of Alloys and Compounds, 2018, 746: 509-519.
[8] ZHANG B Y, YANG G J, LI C X, et al. Non-parabolic isothermal oxidation kinetics of low pressure plasma sprayed MCrAlY bond coat [J]. Applied Surface Science, 2017, 406: 99-109.
[9] LI Y X, SU K Q, BAI P K, et al. Microstructure and property characterization of Ti/TiBCN reinforced Ti based composite coatings fabricated by laser cladding with different scanning speed [J]. Materials Characterization, 2020, 159: 110023.
[10] LI Y X, ZHANG P F, BAI P K, et al. Microstructure and properties of Ti/TiBCN coating on 7075 aluminum alloy by laser cladding [J]. Surface and Coatings Technology, 2018, 334: 142-149.
[11] 苏科强, 李玉新, 张鹏飞, 等. Ti6Al4V表面激光熔覆Ti/TiBCN复合涂层研究 [J]. 表面技术, 2018, 47(12): 142-148.
SU K Q, LI Y X, ZHANG P F, et al. TiBCN coatings prepared on Ti6Al4V surface by laser cladding [J].Surface Technology, 2018, 47(12): 142-148. （in Chinese）
[12] 张鹏飞, 李玉新, 李亮, 等. 7075铝合金表面激光熔覆Ti/TiBCN复合涂层的组织及性能 [J]. 中国表面工程, 2018, 31(2): 159-164.
ZHANG P F, LI Y X, LI L, et al. Microstructure and properties of Ti/TiBCN coating on 7075 aluminum alloy surface by laser cladding [J]. China Surface Engineering, 2018, 31(2): 159-164. （in Chinese）
[13] 张鹏飞, 李玉新, 吴利芸. 铝合金表面激光熔覆技术 [J]. 兵器装备工程学报, 2017, 38(10): 151-155.
ZHANG P F, LI Y X, WU L Y. Status and development of laser cladding on aluminum alloys [J]. Journal of Ordnance Equipment Engineering, 2017, 38(10): 151-155. （in Chinese）
[14] 许瑞华, 黎向锋, 左敦稳, 等. 扫描速度对钛合金NiCoCrAlY熔覆涂层显微组织及硬度的影响 [J]. 稀有金属, 2014, 38(5): 807-812.
XV R H, LI X F, ZUO D W, et al.Microstructure and hardness of NiCoCrAlY coatings on titanium alloy by laser cladding with different scanning speeds [J]. Chinese Journal of Rare Metals, 2014,38(5):807-812. （in Chinese）
[15] 朱红梅, 陈明慧, 唐忠锋, 等. Hastelloy N合金表面激光熔覆NiCoCrAlY涂层在LiF-NaF-KF熔盐中的腐蚀行为研究[J].稀有金属材料与工程, 2018, 47(9): 2767-2774.
ZHU H M, CHEN M H, TANG Z F, et al. Corrosion behavior in molten LiF-NaF-KFsalt of NiCoCrAlY coating prepared by laser cladding on hastelloy N [J]. Rare Metal Materials and Engineering, 2018, 47(9): 2767-2774. （in Chinese）
[16] PEREIRA FALCN J C, ECHEVERRA A, AFONSO C R M, et al. Microstructure assessment at high temperature in NiCoCrAlY overlay coating obtained by laser metal deposition [J]. Journal of Materials Research and Technology, 2019, 8(2): 1761-1772.
[17] PEREIRA J C, ZAMBRANO J C, RAYóN E, et al. Mechanical and microstructural characterization of MCrAlY coatings produced by laser cladding: the influence of the Ni, Co and Al content [J]. Surface and Coatings Technology, 2018, 338: 22-31.
[18] 徐淑文, 陈希章, 苏传出, 等. 工艺参数对激光熔覆层质量的影响 [J]. 热加工工艺, 2020(22): 110-113.
XU S W, CHEN X Z, SU C C, et al. Effect of processing parameters on quality of laser cladding layer [J]. Hot Working Technology, 2020(22): 110-113. （in Chinese）
[19] 王一丹, 张学润, 崔秀芳, 等. 激光能量密度对NiCrCoTiV高熵合金涂层组织结构及耐蚀性能的影响 [J]. 表面技术, 2019, 48(6): 118-124.
WANG Y D, ZHANG X R, CUI X F, et al. Effects of laser energy density on microstructure and corrosion resistance of NiCrCoTiV high entropy alloy coating[J]. Surface Technology, 2019, 48(6): 118-124. （in Chinese）
[20] 杨丹, 宁玉恒, 赵宇光, 等. 工艺参数对304不锈钢表面激光熔覆Ni基合金涂层的组织、耐磨性及耐腐蚀性的影响 [J]. 材料导报, 2017, 31(24): 133-140.
YANG D, NING Y H, ZHAO Y G, et al. Influence of processing parameter on microstructure, wear-resistance and corrosion-resistance of laser cladding Ni-based alloy on the surface of 304 stainless steel[J]. Materials Reports, 2017,31(24):133-140. （in Chinese）
[21] 姚波, 林峰, 马旭龙. 激光微熔覆沉积成形工艺参数对TC4钛合金沉积组织的影响 [J]. 稀有金属材料与工程, 2016, 45(2): 439-444.
YAO B , LIN F , MA X L. Influence of processing parameters on the microstructure of TC4 titanium alloy by laser micro cladding deposition manufacturing [J]. Rare Metal Materials and Engineering, 2016, 45(2): 439-444. （in Chinese）
[22] 谭金花, 孙荣禄, 牛伟, 等. 激光扫描速度对TC4合金表面激光熔覆复合涂层组织及性能的影响 [J]. 材料导报, 2020, 34(12): 12094-12100.
TAN J H, SUN R L, NIU W, et al. Effect of laser scanning speed on microstructure and properties of TC4 alloy surface laser cladding composite coating [J]. Materials Reports, 2020, 34(12): 12094-12100. （in Chinese）

[1]	沈浩，蔡杰，吕鹏，张从林，李玉新，关庆丰. 激光工艺参数对NiCoCrAlYSi熔覆层微观组织及性能的影响[J]. 兵工学报, 2021, 42(7): 1524-1534.
[2]	程文涛，马捷，魏建忠，李洪义，吴龙. 钛合金表面化学气相沉积钼复合涂层制备工艺[J]. 兵工学报, 2020, 41(11): 2320-2325.
[3]	李昌，于志斌，高敬翔，李云飞，韩兴. 物性参数温度变化下激光熔覆多场耦合模拟与实验[J]. 兵工学报, 2019, 40(6): 1258-1270.
[4]	赵尧，虞钢，何秀丽，李海明，李少霞. 基于主成分分析法与逼近理想解法的38MnVS6激光熔覆工艺研究[J]. 兵工学报, 2019, 40(12): 2537-2544.
[5]	石岩，刘东炜，刘佳，李凌宇. 硬脆钢50SiMnVB激光预控裂纹工艺试验研究[J]. 兵工学报, 2018, 39(10): 1997-2005.
[6]	赵丹丹，焦锋. 基于灰色关联分析的35CrMoV钢活塞杆激光熔覆工艺参数优化[J]. 兵工学报, 2018, 39(10): 2073-2080.
[7]	杨臻，张平，蔡志海，秦航. 高强钢激光-电弧复合焊接接头力学性能研究[J]. 兵工学报, 2017, 38(3): 549-554.
[8]	崔凤奎，凌远非，薛进学，李玉玺，李言，解克各. 花键冷滚打成形表层加工硬化研究[J]. 兵工学报, 2017, 38(2): 358-366.
[9]	梁志强，黄迪青，周天丰，李宏伟，乔治，王西彬，刘心藜. 齿轮钢18Cr2Ni4WA磨削烧伤实验及仿真预测研究[J]. 兵工学报, 2017, 38(10): 1995-2001.
[10]	徐婷，李华兵，洪翔，张中威，林炎炎. 激光熔覆TiB₂颗粒增强镍基合金复合涂层的微观组织与摩擦学性能研究[J]. 兵工学报, 2016, 37(8): 1497-1505.
[11]	秦红玲, 周新聪, 闫志敏, 刘正林, 赵新泽. 尾轴承橡胶层厚度和硬度及其交互作用对摩擦性能的影响[J]. 兵工学报, 2013, 34(3): 318-323.
[12]	李萍，章凯，薛克敏，王晓溪. 新型药型罩温压扭成形模拟与实验研究[J]. 兵工学报, 2012, 33(4): 437-442.
[13]	杜军，张平，朱晓莹，蔡志海. 钛合金表面耐冲蚀Zr(AlCu)N涂层的结构与性能[J]. 兵工学报, 2011, 32(12): 1504-1509.
[14]	石岩，张宏，徐春鹰. 激光熔覆科尔莫落依合金涂层的奥氏体不锈钢表面组织和耐磨性研究[J]. 兵工学报, 2010, 31(7): 927-932.
[15]	骆芳，陈智君，楼程华，柴国钟. 塑料模具钢表面激光熔覆陶瓷复合涂层的性能研究[J]. 兵工学报, 2010, 31(7): 933-938.