陶瓷与芳纶层合板叠层结构抗侵彻性能试验研究

doi:10.3969/j.issn.1000-1093.2018.05.018

兵工学报 ›› 2018, Vol. 39 ›› Issue (5): 976-982.doi: 10.3969/j.issn.1000-1093.2018.05.018

陶瓷与芳纶层合板叠层结构抗侵彻性能试验研究

胡年明，陈长海，朱锡，侯海量

（海军工程大学舰船工程系，湖北武汉 430033）

收稿日期:2017-09-20 修回日期:2017-09-20 上线日期:2018-06-22
通讯作者: 陈长海(1985—), 男, 讲师, 博士 E-mail:chenchanghai0746@163.com
作者简介:胡年明(1989—), 男, 博士研究生。E-mail：hunianming@163.com
基金资助:
国家自然科学基金项目(51409253、51479204)

Experimental Research on Anti-penetration Performance of Stacked Structure of Ceramic/Kevlar Composite Laminates

HU Nian-ming, CHEN Chang-hai, ZHU Xi, HOU Hai-liang

(Department of Warship Engineering, Naval University of Engineering, Wuhan 430033, Hubei， China)

Received:2017-09-20 Revised:2017-09-20 Online:2018-06-22

摘要/Abstract

摘要： 为了研究陶瓷与芳纶层合板叠层结构在中高速弹丸侵彻作用下，陶瓷面板对芳纶层合板抗侵彻性能的影响，开展了13.5 g破片模拟弹丸以中高速冲击8 mm厚芳纶板、16 mm厚芳纶板、3 mm厚SiC陶瓷+8 mm厚芳纶板、3 mm厚Al₂O₃陶瓷+8 mm厚芳纶板4种靶板的抗侵彻性能试验。分析了有无前置陶瓷板，芳纶板受到冲击作用后，弹丸及芳纶板变形模式的差异、靶板单位面密度吸能的区别。研究结果表明：前置陶瓷板情况下，弹丸变形较大并伴随着质量磨蚀；前置陶瓷板降低了芳纶板的剪切破坏程度，增加了拉伸变形和层间分层范围；前置陶瓷结构相对于纯芳纶结构在弹速较高时抗侵彻能力较强。

关键词: 陶瓷, 芳纶纤维增强复合材料, 叠层结构, 弹丸, 弹道冲击, 抗侵彻能力

Abstract: The influence of ceramic panel on anti-penetration performance of Kevlar composite laminates during the penetration of high-speed projectile into Kevlar composite laminates is studied. The anti-penetration performances of 8 mm Kevlar composite laminates, 16 mm Kevlar composite laminates, 3 mm SiC ceramic + 8 mm Kevlar composite laminates, and 3 mm Al₂O₃ ceramic + 8 mm Kevlar composite laminates under high-speed penetration with 13.5 g FSP are experimentally investigated. The Deformation modes of projectile and Kevlar laminates with and without ceramic plate and the average absorbed energy per unit area density are analyzed. The results show that the projectile occurs large deformation and is accompanied by a quality abrasion when penetrating the target with front ceramic plate. The front ceramic plate reduces the shear damage degree of Kevlar laminates, and increases the tensile deformation and inter-layer delamination. Compared with pure Kevlar composite laminates, the front ceramic structure has a stronger anti-penetration ability at higher projectile speed. Key

Key words: ceramics, Kevlarfiber-reinforcedcompositelaminate, projectile, laminatestructure, ballisticimpact, anti-penetrationperformance

中图分类号:

O385
TJ012.4

胡年明，陈长海，朱锡，侯海量. 陶瓷与芳纶层合板叠层结构抗侵彻性能试验研究[J]. 兵工学报, 2018, 39(5): 976-982.

HU Nian-ming, CHEN Chang-hai, ZHU Xi, HOU Hai-liang. Experimental Research on Anti-penetration Performance of Stacked Structure of Ceramic/Kevlar Composite Laminates[J]. Acta Armamentarii, 2018, 39(5): 976-982.

参考文献

［1］ Zaera R, Sánchez-Gálvez V. Analytical modeling of normal and oblique ballistic impact on ceramic/metal lightweight armors[J]. International Journal of Impact Engineering, 1998, 21(3):133-148.
[2］ Feli S, Aaleagha M E A, Ahmadi Z. A new analytical model of normal penetration of projectiles into the light-weight ceramic-metal targets[J]. International Journal of Impact Engineering, 2010, 37(5): 561-567.
[3］仲强, 侯海量, 朱锡,等. 陶瓷/液舱复合结构抗侵彻数值分析[J]. 爆炸与冲击, 2017, 37(3):510-519.
ZHONG Qiang, HOU Hai-liang, ZHU Xi, et al. Numerical analysis of penetration resistance of ceramic/fluid cabin composite structure[J]. Explosion and Shock Waves, 2017, 37(3): 510-519. (in Chinese)
[4］王晓强，朱锡，梅志远，等．超高分子量聚乙烯纤维增强层合厚板抗弹性能试验研究[J]．爆炸与冲击，2009，29(1)：29-34.
WANG Xiao-qiang, ZHU Xi, MEI Zhi-yuan, et al. Ballistic performances of ultra-high molecular weight polyethylene fiber-reinforced thick laminated plates[J].Explosion and Shock Waves， 2009, 29(1): 29-34. (in Chinese)
[5］ Wen H M．Predicting the penetration and perforation of FRP laminates struck normally by projectiles with different nose shapes[J]．Composite Structures, 2000, 49(3)：321-329．
[6］虢忠仁，杜文泽，钟蔚华，等．芳纶复合材料对球形弹丸的抗贯穿性能研究[J]．兵工学报，2010，31(4)：458-463．
GUO Zhong-ren，DU Wen-ze，ZHONG Wei-hua，et al. Anti-perforation performance of aramid composite against spheric projectile[J]．Acta Armamentarii，2010，31(4)：458-463．（in Chinese）
[7］ Krishnan K, Sockalingam S, Bansal S, et al. Numerical simulation of ceramic composite armor subjected to ballistic impact[J]. Composites Part B: Engineering, 2010, 41(8):583-593.
[8］ Bürger D, Faria A R D, Almeida S F M D, et al. Ballistic impact simulation of an armour-piercing projectile on hybrid ceramic/fiber reinforced composite armours[J]. International Journal of Impact Engineering, 2012, 43(5):63-77.
[9］ Liu W L, Chen Z H, Chen Z F, et al. Influence of different back laminate layers on ballistic performance of ceramic composite armor[J]. Materials & Design, 2015, 87(8):421-427.

[10］ Monteiro S N, Milanezi T L, Louro L H L, et al. Novel ballistic ramie fabric composite competing with Kevlar^TM fabric in multilayered armor[J]. Materials & Design, 2016, 96(2):263-269.
[11］ Naik N K, Kumar S, Ratnaveer D, et al. An energy-based model for ballistic impact analysis of ceramic-composite armors[J]. International Journal of Damage Mechanics, 2013, 22(2):145-187.
[12］ Tang R T, Wen H M. Predicting the perforation of ceramic-faced light armors subjected to projectile impact[J]. International Journal of Impact Engineering, 2017, 102(4):55-61.
[13］侯海量. 大型舰船水上舷侧结构抗毁伤机理研究 [D]. 武汉: 海军工程大学, 2004.
HOU Hai-liang. Study on mechanism of damage-resistant of large scale surface warship topside structure[D]．Wuhan: Naval University of Engineering, 2006.（in Chinese）

第39卷
第5期2018 年5月兵工学报ACTA
ARMAMENTARIIVol.39No.5May2018

[1]	杨满芝，景钢，郭卫，张传伟，武宏璋，魏凯洋，李林岳，吕振阳，桂皓晨，张晓栋. 精密对称驱动二级微动放大系统设计及性能[J]. 兵工学报, 2022, 43(6): 1456-1465.
[2]	李永鹏，徐豫新，张健，花培鑫，赵晓旭. SiC陶瓷/UHMWPE纤维复合结构抗12.7mm穿甲燃烧弹试验与仿真[J]. 兵工学报, 2022, 43(6): 1355-1364.
[3]	田超，李志鹏，董永香. 表面驻留对陶瓷复合结构抗侵彻特性影响[J]. 兵工学报, 2022, 43(5): 1144-1154.
[4]	张林, 陈斌, 谭清华, 张炜, 高颂. 陶瓷复合装甲抗14.5mm穿燃弹侵彻性能[J]. 兵工学报, 2022, 43(4): 758-767.
[5]	王雪蓉，孙岩，王倩倩，姚凯，孟祥艳，周燕萍，刘运传，马衍东. 基于下落式量热法的碳化硅陶瓷高温比热容测试[J]. 兵工学报, 2022, 43(1): 169-174.
[6]	党泉勇，葛彦鑫，高玉波. 冲击加载下Al₂O₃/SiC复合陶瓷的动态力学行为[J]. 兵工学报, 2022, 43(1): 175-180.
[7]	程申申，陶如意，王浩，薛绍，林庆育. 弹丸不同结构尼龙弹带挤进过程的阻力特性[J]. 兵工学报, 2021, 42(9): 1847-1857.
[8]	任思远, 张庆明, 张晓伟, 田志敏. 环形射流和中心爆炸成型弹丸组合战斗部对混凝土墙的破孔特性[J]. 兵工学报, 2021, 42(8): 1569-1579.
[9]	叶腾钶，徐豫新，武岳，任云燕. 添加TiB₂对石墨烯改性B₄C陶瓷基复合材料抗弹性能的影响[J]. 兵工学报, 2021, 42(7): 1471-1481.
[10]	常丽萍，常亚南，杨雷雷. 内圈倾斜角对高速角接触球轴承动态特性的影响[J]. 兵工学报, 2021, 42(6): 1138-1147.
[11]	邹利波，于存贵，冯广斌，侯保林，仲建林，刘宪福. 基于温度修正的弹丸挤进身管过程摩擦模型[J]. 兵工学报, 2021, 42(6): 1148-1156.
[12]	杨志伟，王良明，钟扬威，王垚，张喜峰. 旋转稳定弹丸非线性角运动吸引域计算方法[J]. 兵工学报, 2021, 42(6): 1195-1203.
[13]	丁树奎，王良明，杨志伟，丁旭冉. 远程火炮弹丸起始扰动的动力学特性[J]. 兵工学报, 2021, 42(4): 673-683.
[14]	任会兰, 赵翰卿, 李尉, 宁建国. 基于离散元法分析增韧陶瓷圆环的动态膨胀碎裂[J]. 兵工学报, 2021, 42(3): 607-616.
[15]	罗中峰，管小荣，徐诚. 面向弹丸炮口状态的自行火炮结构参数全局灵敏度[J]. 兵工学报, 2021, 42(2): 254-267.

陶瓷与芳纶层合板叠层结构抗侵彻性能试验研究

Experimental Research on Anti-penetration Performance of Stacked Structure of Ceramic/Kevlar Composite Laminates

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价