低静电感度叠氮化铜起爆薄膜的制备及其性能

doi:10.3969/j.issn.1000-1093.2022.02.005

摘要/Abstract

摘要： 叠氮化铜的高静电感度限制了其实际应用，碳纤维作为框架材料可以有效降低其静电安全性。以便宜易得的乙酸铜为原料，利用静电纺丝技术，通过碳化、叠氮化制备了碳基叠氮化铜起爆薄膜。制备的叠氮化铜复合薄膜具有一定的柔性，叠氮化铜纳米片均匀生长在碳纤维表面，碳纤维优异的导电性能可以降低其静电感度。通过扫描电镜、红外光谱、X射线衍射仪、比表面积测试和热重分析等对前驱体、碳化中间体和叠氮化铜薄膜都进行了详细的表征。测试结果表明：由于碳纤维优异的导电、导热性能，制备的叠氮化铜起爆薄膜的静电感度降低至1.2 mJ、火焰感度提高至45 cm； 0.65 mg叠氮化铜起爆薄膜在33 μF电容放电条件下，10 V以上电压就可以成功发火，并将铅板炸出凹痕。

关键词: 叠氮化铜, 碳纤维, 微起爆装置, 静电纺丝

Abstract: The high electrostatic sensitivity of copper azide limits its practical application，and carbon fiber as a frame material can effectively reduce its electrostatic safety. A carbon-based copper azide initiating film was prepared using the cheap and easily available copper acetate as the raw materialby carbonization and azide. The prepared copper azide composite film has certain flexibility, and the copper azide nanosheets are uniformly grown on the surface of carbon fibers. The excellent electrical conductivity of carbon fibers can reduce its electrostatic sensitivity. The precursors, carbide intermediates, and copper azide films are all characterized in detail by scanning electron microscope, infrared, X-ray diffraction, specific surface area test and thermogravimetric analysis etc. The test results show that the electrostatic sensitivity of the prepared copper azide initiating film is reduced to 1.2 mJ and the sensitivity to flame is increased to 45 cm since carbon fiber has the excellent electrical and thermal conductivities. The 0.65 mg copper azide initiating film can successfully ignite at a voltage of 10 V or more under the discharge condition of a 33 μF capacitor, and can pit the lead plate.

Key words: copperazide, carbonfiber, micro-initiator, electrospinning

中图分类号:

TQ563⁺.6

闫振展，李龙，杨利，韩纪旻. 低静电感度叠氮化铜起爆薄膜的制备及其性能[J]. 兵工学报, 2022, 43(2): 279-286.

YAN Zhenzhan, LI Long, YANG Li, HAN Jimin. Preparation and Properties of Copper Azide Initiating Film with Low Electrostatic Sensitivity[J]. Acta Armamentarii, 2022, 43(2): 279-286.

参考文献

［1］石城宽,许湘宁,董成.内嵌叠氮化铜碳纳米管复合含能材料的制备与表征[J].爆破器材,2019,48(5):19-23.
SHI C K,XU X N,DONG C.Preparation and characterization of a composite energetic material of carbon nanotubes embedded with copper azide [J].Explosive Materials,2019,48(5):19-23.(in Chinese)
[2] WANG Q Y, HAN J M, ZHANGY Y, et al. Fabrication of copper azide film through metal-organic framework for micro-initiator applications[J]. ACS Applied Materials & Interfaces, 2019, 11(8): 8081-8088.
[3] YU Q X, LI M Y, ZENG Q X, et al. Copper azide prepared by reaction of hollow CuO microspheres with moist HN₃ gas[J]. Materials Letters, 2018, 224: 18-21.
[4] PELLETIER V, BHATTACHARYYA S, KNOKE I, et al. Copper azide confined inside templated carbon nanotubes[J]. Advanced Functional Materials, 2010, 20(18): 3168-3174.
[5] LIU X W, LI T T, HU Y, et al. Copper azide nanowires@rGO energetic composite with low electrostatic sensitivity[J]. Journal of Physics: Conference Series, 2020, 1507(2):022004.
[6] 耶金,杨娜,程彦飞.PDA@Cu(N₃)₂核壳结构起爆药的制备及表征[J].火工品,2020(6):26-29.
YE J,YANG N,CHENG Y F.Preparation and characterization of PDA@Cu(N₃)₂core shell primary explosive [J].Initiators & Pyrotechnics,2020(6):26-29.(in Chinese)
[7] ZHANG L, ZHANG F, WANG Y L. In-situ preparation of copper azide by direct ink writing[J], Materials Letters, 2019, 238: 130-133.
[8] ZHANG F, WANG Y L, BAI Y W, et al. Preparation and characterization of copper azide nanowire array[J]. Materials Letters, 2012, 89: 176-179.
[9] YU C P, ZHANG W C, GUO S Y, et al. A safe and efficient liquid-solid synthesis for copper azide films with excellent electrostatic stability[J]. Nano Energy, 2019, 66: 104135.
[10] XU R, YAN Z Z, YANG L, et al. Nanoscale homogeneous energetic copper azides@ porous carbon hybrid with reduced sensitivity and high ignition ability[J]. ACS Applied Materials & Interfaces, 2018, 10(26): 22545-22551.
[11] 张程刚,胡艳,郭锐,等.填充叠氮化铜的碳纳米管纳米材料的制备研究[J].爆破器材,2017,46(1):1-5.
ZHANG C G,HU Y,GUO R, et al.Preparation of copper azidefilled carbon nanotubes [J].Explosive Materials,2017,46(1): 1-5.(in Chinese)
[12] 王燕兰,张方,张蕾,等.原位反应法制备填充叠氮化铜的碳纳米管阵列[J].含能材料,2016,24(4):386-392.
WANG Y L,ZHANG F,ZHANG L, et al.In-situ preparation of carbon nanotubes array confined with copper azide[J].Chinese Journal of Energetic Materials,2016,24(4):386-392.(in Chinese)
[13] 李娜,许建兵,叶迎华,等.三维多孔微纳米结构叠氮化铜的原位合成及表征[J].火炸药学报,2015,38(4):63-66.
LI N,XU J B,YE Y H, et al.In-situ synthesis and characterization of three-dimensional porous micro-nano-structured copper azide[J].Chinese Journal of Propellant and Explosives,2015,38(4):63-66.(in Chinese)
[14] WANG Q Y, FENG X, WANG S, et al. Explosives: metal-organic framework templated synthesis of copper azide as the primary explosive with low electrostatic sensitivity and excellent initiation ability[J]. Advanced Materials, 2016, 28(28):5766.
[15] SHEN Y, XU J B, LI N, et al. A micro-initiator realized by in-situ synthesis of three-dimensional porous copper azide and its ignition performance[J]. Chemical Engineering Journal, 2017, 326: 1116-1124.
[16] YU Q X, LI M Y, ZENG Q X, et al. Copper azide fabricated by nanoporous copper precursor with proper density[J]. Applied Surface Science, 2018, 442: 38-44.
[17] MATHEY Y, GREIG D R, SHRIVER D F. Variable-temperature Raman and infrared spectra of the copper acetate dimer Cu₂(O₂CCH₃)₄(H₂O)₂and its derivatives[J].Inorganic Chemistry, 1982,21:3409-3413.
[18] ITAB Y, SECOU S, THIERRY D,et al. Forward looking analysis approach to assess copper acetate thermal decomposition reaction mechanism[J]. American Journal of Analytical Chemistry, 2019,10(5): 153-170.
[19] LI Z M, ZHOU M R, ZHANG T L, et al. The facile synthesis of graphene nanoplatelet-lead styphnate composites and their depressed electrostatic hazards[J]. Journal of Materials Chemistry A, 2013(41): 12710-12714.

[1]	秦剑，迟殿鹏，杨利，韩纪旻，佟文超. 金属有机骨架材料孔径对原位合成叠氮化铜-碳复合起爆药的影响规律[J]. 兵工学报, 2022, 43(6): 1295-1303.
[2]	张震东，王雪琴，任杰，刘峥，高原，王玺. 连续碳纤维增强环氧树脂复合材料圆管多胞结构的准静态压缩响应[J]. 兵工学报, 2022, 43(5): 1185-1193.
[3]	孙久哲, 赵鸿浩, 韩永康, 许嘉威, 付玉彬. 水合肼掺氮改性碳纤维电极电化学及电场响应性能[J]. 兵工学报, 2022, 43(2): 363-371.
[4]	韩永康, 赵鸿浩, 孙久哲, 许嘉威, 付玉彬. 氨基酸改性碳纤维电极电化学及海洋电场响应性能[J]. 兵工学报, 2022, 43(2): 434-441.
[5]	彭露玫，周成康，张志勇，刘冬. 金属与碳纤维复合结构发射箱耐高温冲击性能[J]. 兵工学报, 2021, 42(11): 2360-2367.
[6]	袁野，王丽燕，曹占伟，聂春生，聂亮，马昊军. 碳纤维增强类复合材料烧蚀产物对等离子体流场特性影响的实验研究[J]. 兵工学报, 2020, 41(2): 298-304.
[7]	易镇鑫，曹亚清，张琳，朱顺官，朱晨光. 新型碳基导电药无桥火工品研究[J]. 兵工学报, 2019, 40(8): 1596-1602.
[8]	宋玉苏，李红霞，申振，王烨煊. 碳纤维海洋电场电极探测机理和性能研究[J]. 兵工学报, 2019, 40(3): 570-575.
[9]	常青，张敏弟，马潇健，黄彪，黄国豪. 碳纤维复合材料各向异性特性对气泡形态影响试验研究[J]. 兵工学报, 2019, 40(11): 2272-2282.
[10]	申振, 宋玉苏, 王月明. 高性能碳纤维水下电场电极制备及其性能测量[J]. 兵工学报, 2017, 38(11): 2190-2197.
[11]	张辽远，尚明伟，赵炎，姜大林，马康乐. 金刚石线锯切割碳纤维复合材料实验研究[J]. 兵工学报, 2016, 37(11): 2044-2049.
[12]	苏飞，袁军堂，于斌斌，汪振华. 碳纤维增强复合材料的铣削实验和微观形貌分析[J]. 兵工学报, 2014, 35(4): 531-539.
[13]	高航，袁和平. 碳纤维复合材料构件干磨削砂轮研制及其加工性能研究[J]. 兵工学报, 2011, 32(2): 186-191.
[14]	范立佳，董相廷，高续波，王进贤，刘桂霞. 静电纺丝技术制备BaFe₁₂O₁₉纳米纤维与表征[J]. 兵工学报, 2011, 32(1): 112-117.
[15]	1:庞思勤;2:刘伟成. 激光加工高性能复合枒料的エ艺与机理[J]. 兵工学报, 1992, 13(4): 84-91.