基于光纤陀螺仪检测的精密温控装置优化设计

doi:10.12382/bgxb.2021.0187

摘要/Abstract

摘要： 针对高精度光纤陀螺仪产品需在无明显气流的大尺度空间内进行批量检测的迫切问题，研究以辐射冷板为核心元件优化设计精密温控装置，并通过理论、模拟和实验的方法实现对该装置可靠性的验证。研究结果表明：优化设计效果显著，可实现检测空间范围内空间温度均匀性不大于2 ℃，24 h内温度波动不大于±0.05 ℃，温度扰动作用下温度场恢复时间不超过30 min；该优化研究解决检测环境温度控制中要求无风低波动的技术难题，突破传统技术路线中对检测空间的限制，实现高精度光纤陀螺仪在较大尺度空间的批量检测。

关键词: 光纤陀螺仪, 精密温控, 大尺度空间, 辐射冷板, 优化设计

Abstract: The high-precision fiber optic gyroscope (FOG) products need to be tested in batches in a large-scale space without obvious air flow. For this purpose, the optimization design of precision temperature control device with radiation cold plate as the core element is studied，and the reliability of the device is verified by theoretical，simulation and experimental methods. The effect of optimization design is remarkable. The results show that the temperature uniformity is no more than 2 ℃，the temperature fluctuation is no more than ±0.05 ℃ within 24 hours，and the recovery time of temperature field is no more than 30 minutes under the effect of temperature fluctuation. The optimization research solves the technical problem of no wind and low fluctuation in the detection of ambient temperature control，breaks through the limitation of detection space in the traditional technical route，and realizes the batch detection of high-precision fiber optic gyroscopes in large scale space.

Key words: fibreopticgyroscope, high-precisiontemperaturecontrol, largescalespace, radiationcoldplate, optimaldesign

中图分类号:

V241.5

孙宁，夏艳，程行清. 基于光纤陀螺仪检测的精密温控装置优化设计[J]. 兵工学报, 2022, 43(4): 910-918.

SUN Ning， XIA Yan， CHENG Xingqing. Optimal Design of High-precision Temperature Control System for FOG Detection[J]. Acta Armamentarii, 2022, 43(4): 910-918.

参考文献

［1］赵砚驰, 程建华, 赵琳.惯性导航系统陀螺仪的发展现状与未来展望［J］.导航与控制, 2020, 19(4/5): 189-195.
ZHAO X C, CHENG J H, ZHAO L. Development status and future prospects of gyroscope in inertial navigation［J］. Navigation and Control 2020, 19(4/5): 189-195. (in Chinese)
［2］许保祥, 熊智, 黄继勋, 等.光纤固定胶粘剂对光纤陀螺低温零偏误差的影响［J］.兵工学报, 2021, 42(6): 1223-1229.
XU B X, XIONG Z, HUANG J X, et al. Effect of adhesive on the zero drift of interferometric fiber-optic gyroscope in low temperature environment［J］.Acta Armamentarii, 2021, 42(6):1223-1229. (in Chinese)
［3］王鹏飞, 林媛.高精度光纤陀螺技术的发展与思考［J］. 舰船电子工程, 2020, 40(12): 11-15.
WANG P F, LIN Y.Development and prospect of high precision fiber optical gyroscope technology［J］.Ship Electronic Engineering, 2020, 40(12):11-15. (in Chinese)
［4］吕志刚, 吴爽, 白龙.光纤惯导国内外发展现状及其关键技术分析［J］.数字海洋与水下攻防, 2020, 3(5): 420-424.
L Z G, WU S, BAI L.Development status and key technology analysis of optical fiber inertial navigation system in China and abroad［J］.Digital Ocean & Underwater Warfare, 2020, 3(5): 420-424. (in Chinese)
［5］王巍. 纤陀螺在宇航领域中的应用及发展趋势［J］. 导航与控制, 2020, 19(4/5):18-27.
WANG W.Application and development tendency of fiber optic gyroscope in space［J］. Navigation and Control, 2020, 19(4/5): 18-27. (in Chinese)
［6］ LOFT C M, RUFFIN P B, PARKER M D, et al. Investigation of the effects of temporal thermal gradients in fiber optic gyroscope sensing coils［J］.Optical Engineering, 1995, 34(10): 2856-2863.
［7］黄冬.高精度光纤陀螺仪研究［D］.西安:西安石油大学, 2019.
HUANG D.Research on high precision fiber optic gyroscope ［D］. Xi'an: Xi'an Shiyou University, 2019. (in Chinese)
［8］刘强.高低温环境试验箱设计及性能优化分析［D］.淮南:安徽理工大学, 2020.
LIU Q. Design and performance analysis of high and low temperature environmental test chamber［D］.Huainan:Anhui University of Science and Technology, 2020.(in Chinese)
［9］陈忠灿, 承磊, 王天祥, 等.空间热环境模拟技术的发展及研究现状［J］.低温与超导, 2016, 44(4): 6-13.
CHEN Z C, CHENG L, WANG T X, et al. Development and status of space thermal environment simulation researches［J］. Cryogenics & Superconductivity, 2016, 44(4): 6-13. (in Chinese)
［10］赵培炎.超精密加工中的热误差控制及对策［J］. 国防科技参考, 1989(1): 109-117.
ZHAO P Y. Thermal error control and countermeasures in ultra precision machining［J］. National Defense Science and Technology Reference, 1989(1):109-117. (in Chinese)
［11］王宪平, 李圣宜.超精密环境温度控制及温度测量技术研究［J］.中国机械工程, 2000, 11(8): 869-871.
WANG X P, LI S Y. Research on ultra-precision environmental temperature control and measurement［J］.China Mechanical Engineering, 2000, 1(8): 869-871. (in Chinese)
［12］张日升, 李尚政, 刘宏, 等.精密加工局域温度控制技术研究［J］. 机械, 2002, 29(增刊1): 26-28.
ZHANG R S, LI S Z, LIU H, et al. Research on local temperature control technology of precision machining［J］. Machinery, 2002, 29(S1): 26-28. (in Chinese)
［13］刘大伟. 精密温控在光纤陀螺仪中的研究与应用［D］. 哈尔滨:哈尔滨工程大学, 2003.
LIU D W. Research and application of precision temperature control in fiber optical gyroscope［D］. Harbin: Harbin Engineering University, 2003. (in Chinese)
［14］王彦, 陈淑芬, 袁家虎.光纤陀螺温控技术的研究［J］. 应用光学, 2000(增刊1):61-63, 71.
WANG Y, CHEN S F, YUAN J H. Research on temperature control technology of FOG［J］. Journal of Applied Optics, 2000(S1): 61-63, 71. (in Chinese)
［15］程建华, 陈李, 李明月. 船用光纤陀螺精密温控系统的设计与实现［J］. 中国惯性技术学报, 2011, 19(4): 403-407.
CHENG J H, CHEN L, LI M Y. Design and realization of precision temperature control system for shipborne FOG［J］. Journal of Chinese Inertial Technology, 2011, 19(4): 403-407. (in Chinese)
［16］罗立成.光纤陀螺精密温度控制系统的设计及其研究［D］. 哈尔滨:哈尔滨工程大学, 2011.
LUO L C.Research and design of high-precision temperature control system for FOG［D］.Harbin:Harbin Engineering University, 2011. (in Chinese)
［17］陈李.基于TMS320C6713B 的精密温度控制系统设计与实现［D］. 哈尔滨: 哈尔滨工程大学, 2012.
CHEN L. Designing and implement of high-precision temperature control system based on TMS320C6713B ［D］.Harbin:Harbin Engineering University, 2012.(in Chinese)
［18］胡旭晓, 杨克己, 台宪青. 逐级递推式超精密温度控制策略研究［J］. 机械工程学报, 2004, 40(2): 64-67.
HU X X, YANG K J, TAI X Q. Research on step by step recursive ultra precision temperature control strategy［J］. Chinese Journal of Mechanical Engineering, 2004, 40(2): 64-67. (in Chinese)
［19］杨启伟, 陈以.常用温度控制法的对比［J］.测控技术, 2005, 24(6): 86-88.
YANG Q W, CHEN Y.Contrast research of universal temperature control methods［J］.Measurement and Control Technique, 2005, 24(6): 86-88. (in Chinese)
［20］杨世铭, 陶文铨.传热学［M］. 北京: 高等教育出版社, 2006.
YANG S M, TAO W Q. Heat transfer［M］. Beijing: Higher Education Press, 2006. (in Chinese)
［21］王起霄, 卢维国. 制冷装置冷凝器系统的设计及研究［J］.哈尔滨商业大学学报: 自然科学版, 2010, 26(5): 604-607.
WANG Q X, LU W G. Design and research of condenser system in refrigeration unit［J］. Journal of Harbin University of Commerce (Natural Sciences Edition), 2010, 26(5): 604-607. (in Chinese)
［22］郑大宇, 王冠弘, 刘卫党, 等.冷库保温结构优化分析［J］.哈尔滨商业大学学报(自然科学版), 2011, 27(3): 339-341.
ZHENG D Y, WANG G H, LIU W D, et al．Improvements and analysis of cold store thermodynamics insulation［J］. Journal of Harbin University of Commerce (Natural Sciences Edition), 2011, 27(3): 339-341. (in Chinese)
［23］陆耀庆. 实用供热空调设计手册［M］. 北京:中国建筑工业出版社，2008.
LU Y Q. Practical heating and air conditioning design manual ［M］. Beijing: China Construction Industry Press, 2008. (in Chinese)
［24］王娟, 朱武, 欧阳峥嵘.低温泵辐射挡板的结构及其对辐射热负荷的影响［C］∥第四届华东真空科技学术交流展示会.鹰潭:安徽省真空学会, 2003.
WANG J, ZHU W, OUYANG Z R.Structure of radiant baffle of cryopump and its effect on radiant heat load［C］∥Proceedings of the 4th East China Vacuum Technology Academic Exchange and Exhibition.Yingtan: Anhui Vacuum Society, 2003. (in Chinese)
［25］达道安.真空设计手册［M］.北京: 国防工业出版社, 1981.
DA D A. Vacuum design manual［M］.Beijing:National Defense Industry Press, 1981. (in Chinese)
［26］吉爱红.低温装置辐射冷屏及其材料表面特性的研究［D］.合肥: 中国科学院合肥物质科学研究院, 2000.
JI A H. Study on the surface characteristics of radiation cold screen and its materials in cryogenic device［D］.Hefei:Hefei Institutes of Physical Science, Chinese Academy of Sciences, 2000. (in Chinese)
［27］关文吉.供暖通风空调设计手册［M］.北京:中国建材工业出版社, 2016.
GUAN W J. Heating ventilation and air conditioning design manual［M］.Beijing:China Building Materials Industry Press, 2016:45-65. (in Chinese)
［28］冯文帅.高精度陀螺仪发展综述［C］∥第四届航天电子战略研究论坛论文集.北京:中国航天科技集团公司第九研究院科学技术委员会, 2018: 74-77.
FENG W S. Overview of the development of high precision gyroscopes［C］∥Proceedings of the 4th Aerospace Electronics Strategic Research Forum. Beijing: Science and Technology Committee of the Ninth Research Institute, China Aerospace Science and Technology Corporation, 2018:74-77. (in Chinese)

[1]	吴则良，叶建川，王江，金忍. 基于深度自动编码器神经网络的飞行器翼型参数降维与优化设计[J]. 兵工学报, 2022, 43(6): 1326-1336.
[2]	刘钧圣，王刚，王琨，史宏博，郭斌. 考虑不确定性的模块化战术导弹优化设计[J]. 兵工学报, 2020, 41(2): 270-279.
[3]	张富毅，吴钦，赵晓阳，刘影，王国玉. 基于响应面方法的喷水推进器进水流道多目标优化[J]. 兵工学报, 2020, 41(10): 2071-2080.
[4]	魏巍，彭卉，刘旭，简洪超，谢文浩，闫清东，朱浩月. 液力传动车辆闭锁充油动态缓冲特性优化[J]. 兵工学报, 2019, 40(7): 1358-1364.
[5]	林通，钱林方，陈光宋，刘太素. 面向输弹一致性的某输弹机稳健优化设计研究[J]. 兵工学报, 2019, 40(2): 243-250.
[6]	李彬，庞永杰，朱枭猛，程妍雪. 水下航行器环肋复合材料耐压壳6σ优化设计[J]. 兵工学报, 2018, 39(6): 1171-1177.
[7]	姚琳, 马大为, 马吴宁，任杰, 仲健林, 王泽林. 两级提拉式单侧弹射装置内弹道建模与优化[J]. 兵工学报, 2017, 38(3): 466-475.
[8]	刘勤，孙志礼，刘英，郭志明，陈岩. 基于改进布谷鸟搜索算法的结构耐久性优化方法[J]. 兵工学报, 2017, 38(12): 2438-2446.
[9]	李志斌，卢芳云. 梯度温度场中多胞材料牺牲层的抗冲击分析[J]. 兵工学报, 2017, 38(12): 2463-2471.
[10]	刘强，胡灯亮，吴波，任元，王卫杰. 磁悬浮微框架球形飞轮及其转子优化设计研究[J]. 兵工学报, 2017, 38(11): 2280-2288.
[11]	高庆玉，唐乾刚，张青斌，丰志伟. 空间绳网二级发射模式动力学分析[J]. 兵工学报, 2016, 37(4): 719-726.
[12]	穆洪斌，魏巍，闫清东，刘城. 双循环圆液力缓速器叶片顶弧优化设计[J]. 兵工学报, 2016, 37(3): 400-407.
[13]	蔡云骧，周志勇，徐小倩，毕道鹍. 一种基于精英策略非支配排序遗传算法-Ⅱ的多层吸波涂层结构设计方法[J]. 兵工学报, 2015, 36(8): 1574-1579.
[14]	姚琳，马大为，王玺，朱忠领，何强. 冷弹射系统动力学响应与油气悬架优化设计[J]. 兵工学报, 2015, 36(7): 1228-1236.
[15]	刘勤，钱云鹏，姬广振，孙志礼. 随机载荷作用下扭力轴耐久性优化设计[J]. 兵工学报, 2015, 36(5): 933-937.