无水冷条件下温度与热流复合传感器设计与试验

doi:10.3969/j.issn.1000-1093.2016.02.001

兵工学报 ›› 2016, Vol. 37 ›› Issue (2): 193-202.doi: 10.3969/j.issn.1000-1093.2016.02.001

• 论文 • 下一篇

无水冷条件下温度与热流复合传感器设计与试验

杨庆涛^1，2，王辉²，朱新新²，周平²

(1.中国空气动力研究与发展中心空气动力学国家重点实验室，四川绵阳 621000；

收稿日期:2015-06-02 修回日期:2015-06-02 上线日期:2016-04-22
通讯作者: 杨庆涛 E-mail:yqt06@mails.tsinghua.edu.cn
作者简介:杨庆涛(1975—)男副研究员，硕士
基金资助:
空气动力学国家重点实验室基金项目（JBKY14050502）

Design and Test of a Hybrid Sensor for Temperature and Heat Flux Measurement without Water-cooling

YANG Qing-tao^1,2, WANG Hui², ZHU Xin-xin², ZHOU Ping²

(1.State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center,2Hypervelocity Aerodynamics Institute, China Aerodynamics Research and Development Center, Mianyang 621000, Sichuan, China)

Received:2015-06-02 Revised:2015-06-02 Online:2016-04-22
Contact: YANG Qing-tao E-mail:yqt06@mails.tsinghua.edu.cn

摘要/Abstract

摘要： 针对飞行试验中参数测量需求，研究长时间飞行过程中无水冷条件下传感器表面温度和热流的快速响应测量技术。在分析环境特点和测量需求的基础上，设计一种自锁紧固的柱塞式复合传感器，根据圆柱体侧面的温度响应处理得到表面温度和热流。提出一种基于最小二乘法的多项式拟合数据处理方法，有限元数值分析表明，该方法能够获得更好的数据抗畸变和抗噪声能力。标定该热流传感器的热流测量结果，得到不锈钢传感器的98%热流响应时间约为0.7 s，热流测量结果受到侧向隔热结构的影响明显。表面温度对比试验结果表明，该传感器所测结果能够反映表面温度对热流的影响。

关键词: 仪器仪表技术, 表面温度, 热流测量, 快速响应, 传感器

Abstract: A method for rapid measurement of surface temperature and heat flux in the absence of water-cooling during long-time flight is studied for the parameter measurement demands in hypersonic flight test. Based on the analysis of environment characteristics and measurement demands, a novel plug hybrid sensor with self-fastening structure is designed, which could be used to achieve the surface temperature and heat flux data according to the measured result of temperature on the side of a cylinder. A polynomial approximation method based on the least square method is presented. FEA simulation results show that better anti-distortion and anti-noise performances could be achieved using the proposed method. The sensor is calibrated in an arc lamp heat flux sensor calibration system for heat flux verification. 98% response time of stainless steel sensor is about 0.7s. In addition, the measured results of heat flux are affected evidently by the adiabatic structure. The comparative test results of surface temperature show that the data achieved by the sensor could reflect the effect of surface temperature on heat flux.

Key words: apparatus and instruments technology, surface temperature, heat flux measurement, rapid response, sensor

中图分类号:

V441

杨庆涛，王辉，朱新新，周平. 无水冷条件下温度与热流复合传感器设计与试验[J]. 兵工学报, 2016, 37(2): 193-202.

YANG Qing-tao, WANG Hui, ZHU Xin-xin, ZHOU Ping. Design and Test of a Hybrid Sensor for Temperature and Heat Flux Measurement without Water-cooling[J]. Acta Armamentarii, 2016, 37(2): 193-202.

参考文献

［1］刘初平. 气动热与热防护试验热流测量[M]. 北京：国防工业出版社，2013.
LIU Chu-ping. Heat flux measurement in aerothermodynamics and thermal protection tests[M]. Beijing: National Defense Industry Press, 2013. (in Chinese)
[2] Kimmel R L, Adamczak D, Juliano T J.HIFiRE-5 flight test preliminary results[C]∥51st AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. Texas, US: American Institute of Aeronautics and Astronautics, 2013.
[3] Juliano T J, Adamczak D, Kimmel R L.HIFiRE-5 flight test heating analysis[C]∥52nd Aerospace Sciences Meeting. Maryland, US: American Institute of Aeronautics and Astronautics, 2014.
[4] Del Vecchio A, Marino G, Thoemel J, et al. EXPERT - the ESA experimental re-entry vehicle: overview of the experiments and payloads qualified and accepted for the flight[C]∥39th AIAA Fluid Dynamics Conference. Texas, US:American Institute of Aeronautics and Astronautics, 2009.
[5] Constantine P G, Doostan A, Wang Q, et al. A surrogate accelerated Bayesian inverse analysis of the HyShot Ⅱ flight data[C]∥52nd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference. Colorado,US:American Institute of Aeronautics and Astronautics, 2011.
[6] Preci A, Herdrich G, Fasoulas S, et al. Assembly, integration and test of the sensor system COMPARE for SHEFEX Ⅱ[C]∥42nd AIAA Thermophysics Conference. Havaii, US:American Institute of Aeronautics and Astronautics, 2011.
[7] Chen F J, Berry S A. HyBoLT flight experiment, NASA/TM-2010-216725 [R]. Hanover, MD: NASA Center for AeroSpace Information, 2010.
[8] Baiocco P. PRE-X experimental re-entry lifting body: design of flight test experiments for critical aerothermal phenomena, RTO-EN-AVT-130[R]. Neuilly-sur-Seine,France: RTO, 2007.
[9] Gülhan A, Siebe F, Thiele T, et al. Instrumentation of the SHEFEX-Ⅱ flight experiment and selected flight data[C]∥18th AIAA/3AF International Space Planes and Hypersonic Systems and Technologies Conference. Tours, France:American Institute of Aeronautics and Astronautics, 2012.
[10] Del Vecchio A, Marino G, Gardi R, et al.CIRA experiments and payloads flying on EXPERT - the ESA experimental re-entry vehicle[C]∥17th AIAA International Space Planes and Hypersonic Systems and Technologies Conference. California,US: the American Institute of Aeronautics and Astronautics, 2011.
[11] ASTM. ASTM E 511-01 Standard test method for measuring heat flux using a Copper-Constantan circular foil, heat-flux transducer [S]. US:ASTM, 2001.
[12] 杨庆涛，王辉. 戈登计热流测量影响因素分析[C/CD]∥中国工程热物理学会传热传质学年会论文集. 上海：中国工程热物理学会，2010.
YANG Qing-tao, WANG Hui. Analysis on affecting factors of Gardon gage heat flux measurement[C/CD]∥Heat and Mass Transfer Conference of Chinese Society of Engineering Thermophysics. Shanghai, China: Chinese Society of Engineering Thermophysics, 2010. (in Chinese)
[13] ASTM. ASTM E 457-96 Standard test method for measuring heat-transfer rate using a thermal capacitance (slug) calorimeter [S].US:ASTM, 1996.
[14] Reimer T, Stubicar K, Koppenwallner G, et al.Overview about the instrumented nose assembly development for the expert capsule [C]∥16th AIAA/DLR/DGLR International Space Planes and Hypersonic Systems and Technologies Conference. Bremen, Germany: American Institute of Aeronautics and Astronautics, 2009.
[15] 杨庆涛，白菡尘，张涛,等. 快速响应热流/温度传感器设计与特性分析[J]. 兵工学报, 2014, 35(6): 927-934.
YANG Qing-tao, BAI Han-chen, ZHANG Tao, et al. Design and response characteristics analysis of a fast-response sensor for temperature and heat flux measurement [J]. Acta Armamentarii, 2014, 35(6): 927-934. (in Chinese)
[16] Smith T B, Schetz J A, Walker D G.Development and ground testing of heat flux gages for high enthalpy supersonic flight tests [C]∥22nd AIAA Aerodynamic Measurement Technology and Ground Testing Conference. St. Louis, Missouri, US: American Institute of Aeronautics and Astronautics, 2002.
[17] Terrell J, Hager J, Onishi S, et al. Heat flux microsensor measurements [C]∥AIAA Fourth International Aerospace Planes Conference. Orlando, FL, US:American Institute of Aeronautics and Astronautics, 1992.
[18] Coy E B. Measurement of transient heat flux and surface temperature using embedded temperature sensors[J]. Journal of Thermophysics and Heat Transfer, 2010, 24(1): 77-84.
[19] Coy E B, Bergkoetter M, Danczyk S A, et al. An efficient approach for multidimensional inverse heat conduction[C]∥50th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. Nashville, Tennessee, US: American Institute of Aeronautics and Astronautics, 2012: 1-16.
[20] ASTM. ASTM E 459-97 Standard test method for measuring heat transfer rate using a thin-skin calorimeter [S].US: ASTM, 1997.
[21] Savitzky A, Golay M. Smoothing and differentiation of data by simplified least squares procedures[J]. Analytical Chemistry, 1964, 36(8): 1627-1639.

[1]	王武，付小强，卢青山，薛鹏，岳小东. 某型火箭炮运弹车自动调平控制系统的设计与实现[J]. 兵工学报, 2022, 43(S1): 82-87.
[2]	张昀普，单甘霖. 道路约束下多传感器协同地面目标跟踪的管理方法[J]. 兵工学报, 2022, 43(3): 542-555.
[3]	郭成豹，胡松，王文井，殷琦琦. 利用磁传感器阵列磁场差值的舰船磁场反演建模方法[J]. 兵工学报, 2022, 43(1): 111-119.
[4]	王冠群，张春华，张舒然. 基于分治贪心思想的联合多站目标关联定位[J]. 兵工学报, 2021, 42(12): 2700-2709.
[5]	王睿，李新娥，马铁华，杜红棉，陆阳洋. 基于容栅传感器的二维微小位移测量方法研究[J]. 兵工学报, 2020, 41(7): 1441-1448.
[6]	沈杰，潘绪超，方中，何勇，陈鸿，张江南，史云雷. 强电磁脉冲对硅微惯性传感器的损伤效应研究[J]. 兵工学报, 2020, 41(6): 1157-1164.
[7]	王领，申晓红，康玉柱，花飞，王海燕. 水声传感器网络信号到达时间差目标定位的最小二乘法估计性能[J]. 兵工学报, 2020, 41(3): 542-551.
[8]	李军宝，李伟兵，汪衡，袁书强，王晓鸣，洪晓文，徐赫阳. 爆炸载荷下铝粉与橡胶复合材料中的冲击波传播特性[J]. 兵工学报, 2020, 41(10): 2001-2007.
[9]	李洪瑞. 基于神经网络的分布式被动传感器信息融合技术[J]. 兵工学报, 2020, 41(1): 95-101.
[10]	赵其进，廖自力，张运银，蔡立春. 轮毂电机全速度范围无位置传感器控制研究[J]. 兵工学报, 2019, 40(5): 915-926.
[11]	罗静博，陈浩，赵苗, 翟国君. 基于改进型入侵野草算法的三轴磁传感器非正交误差校正[J]. 兵工学报, 2019, 40(12): 2513-2518.
[12]	乔成林，单甘霖，段修生，郭峰. 多平台主动与被动传感器协同跟踪的长时调度方法[J]. 兵工学报, 2019, 40(1): 115-123.
[13]	文学，谭建平，刘溯奇，李新和. 超薄壁回转件旋压后外径在机测量方法研究[J]. 兵工学报, 2018, 39(8): 1612-1621.
[14]	杨廷鸿，方海洋，姜大立，方玲. 考虑最大暴露值的无线传感器网络最小暴露路径优化算法[J]. 兵工学报, 2018, 39(4): 743-752.
[15]	徐公国，段修生，单甘霖，童俊. 基于多目标局部变异-自适应量子粒子群优化算法的复杂地形多传感器优化部署[J]. 兵工学报, 2018, 39(11): 2192-2201.

无水冷条件下温度与热流复合传感器设计与试验

Design and Test of a Hybrid Sensor for Temperature and Heat Flux Measurement without Water-cooling

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价