控制油压对湿式多片离合器分离动态特性的影响

doi:10.12382/bgxb.2021.0506

摘要/Abstract

摘要： 湿式多片离合器分离过程的持续时间、转矩变化和间隙分布会影响车辆换挡品质。考虑摩擦副间流体动压润滑、微凸体弹塑性接触、花键摩擦力以及活塞回位之后与离合器毂的碰撞，建立湿式多片离合器分离过程动力学数值模型，研究六摩擦副系统在不同初始控制油压和油压下降速率下的动态分离过程，提出了不均匀系数以表征分离间隙均匀度。研究结果表明：油压下降速率的减小显著延长了分离过程持续时间，恶化了分离间隙均匀度，减缓了粗糙接触转矩的下降，增大了分离过程中的黏性转矩；而初始控制油压对分离过程持续时间和分离间隙均匀度影响较小，但初始控制油压的增加增大了粗糙接触转矩的初始值和衰减速率，并减小了分离过程中的黏性转矩。

关键词: 湿式多片离合器, 分离特性, 控制油压, 摩擦转矩, 摩擦副间隙

Abstract: During the disengaging process of a wet-multi clutch, the disengaging time, the friction torque and the friction pair gaps have a dramatic influence on the shifting quality of the vehicle. Thus, a comprehensive dynamic model is proposed to investigate the clutch disengaging process, which includes hydrodynamic lubrication, elastic-plastic contact between asperities, spline friction, and impact between piston and clutch hub. The influence of control oil pressure and its decreasing rate on the disengaging performance of a six friction-pair wet clutch are studied, and the non-uniformity coefficient is employed to characterize the disengaging uniformity. The results show that the decline in the pressure's decreasing rate not only prolongs the disengaging time, but also deteriorates the disengaging uniformity dramatically. Moreover, the decline in contact torque is retarded and the viscous torque is increased. However, the initial value of control oil pressure has a slight influence on the disengaging time and uniformity. The rise in control oil pressure increases the initial contact torque and its decreasing rate, and also decreases the viscous torque.

Key words: wetmulti-discclutch, disengagingperformance, controloilpressure, frictiontorque, frictionpairgaps

中图分类号:

U463.211

郑良杰，马彪，陈漫，于亮，张存振. 控制油压对湿式多片离合器分离动态特性的影响[J]. 兵工学报, 2022, 43(10): 2451-2459.

ZHENG Liangjie, MA Biao, CHEN Man, YU Liang, ZHANG Cunzhen. Influence of the Control Oil Pressure on the Dynamic Characteristics of a Wet Multi-disc Clutch in the Disengaging Process[J]. Acta Armamentarii, 2022, 43(10): 2451-2459.

参考文献

［1］马彪, 李国强, 李和言, 等. 基于改进平均流量模型的离合器接合特性仿真[J]. 吉林大学学报(工学版), 2014, 44(6):1557-1563.
MA B, LI G Q, LI H Y, et al.Simulation of wet clutch engagement characteristics based on advanced average flow model[J].Journal of Jilin University (Engineering and Technology Edition), 2014, 44(6):1557-1563. (in Chinese)
[2］ YU L, MA B, CHEN M, et al.Numerical and experimental studies on the characteristics of friction torque based on wet paper-based clutches[J].Tribology International, 2019, 131:541-553.
[3］ YU L, MA B, CHEN M, et al. Variation mechanism of the friction torque in a Cu-based wet clutch affected by operating parameters[J]. Tribology International, 2020, 147:106169.
[4］吴健鹏, 马彪, 李和言, 等. 考虑接触面局部散热的湿式离合器摩擦片滑摩温升特性[J]. 北京理工大学学报, 2019, 39(9): 925-932.
WU J P, MA B, LI H Y, et al.Temperature rise characteristic of friction disc in wet clutch considering the local heat dissipation on the contact surface [J]. Transactions of Beijing Institute of Technology, 2019, 39(9):925-932. (in Chinese)
[5］马彪, 陈飞, 李和言, 等. 湿式离合器摩擦副平均温升特性研究[J]. 兵工学报, 2016, 37(6):961-968.
MA B, CHEN F, LI H Y, et al.Research on average temperature rise characteristic of wet clutch[J].Acta Armamentarii, 2016, 37(6): 961-968. (in Chinese)
[6］杨立昆, 马彪, 李和言. 湿式离合器接合过程摩擦振颤的影响因素[J]. 北京理工大学学报, 2016, 36(7):673-678.
YANG L K, MA B, LI H Y. Influence factors of friction-induced oscillation during wet clutch engagement [J]. Transactions of Beijing Institute of Technology, 2016, 36(7):673-678. (in Chinese)
[7］赵二辉, 马彪, 李和言, 等. 转速对湿式离合器局部润滑及摩擦特性影响研究[J]. 兵工学报, 2017, 38(4):625-633.
ZHAO E H, MA B, LI H Y, et al.Influence of rotating speed on local lubrication and friction characteristics of wet clutch [J]. Acta Armamentarii, 2017, 38(4):625-633. (in Chinese)
[8］ YU L, MA B, ZHENG C S, et al. Study on the groove area effects on the friction-wear properties of a Cu-based wet clutch [J]. Tribology International, 2021, 163:107096.
[9］ IQBAL S, AL-BENDER F, PLUYMERS B, et al. Model for predicting drag torque in open multi-disks wet clutches [J]. Journal of Fluids Engineering, 2014, 136(2):021103.
[10］ HU J B, HOU S Y, WEI C. Drag torque modeling at high circumferential speed in open wet clutches considering plate wobble and mechanical contact [J]. Tribology International, 2018, 124:102-116.
[11］张琳, 魏超, 胡纪滨, 等. 车用空载湿式离合器高速碰撞摩擦特性及带排转矩分析[J]. 兵工学报, 2020, 41(7): 1270-1279.
ZHANG L, WEI C, HU J B, et al.Rub-impact characteristics and drag torque at high circumferential velocities in no-load multi-plate wet clutch for vehicles [J]. Acta Armamentarii, 2020, 41(7): 1270-1279. (in Chinese)
[12］ ZHANG L, WEI C, HU J B, et al.Nonlinear dynamic characteristics of rub-impact process at high circumferential velocities in no-load multiplate wet clutch [J]. Tribology Transactions, 2020, 63(1):101-119.
[13］成宵, 朱茂桃, 田乃利. 油相-气相两相流对湿式离合器带排转矩影响的数值分析[J]. 兵工学报, 2020, 41(5):850-857.
CHENG X，ZHU M T, TIAN N L. Numerical analysis of effect of liquid-gas two-phase flow on the drag torque characteristics of wet clutch[J]. Acta Armamentarii, 2020, 41(5):850-857. (in Chinese)
[14］师路骐, 马彪, 李和言, 等. 全程转速下浮动支撑湿式离合器带排转矩计算模型与验证[J]. 兵工学报, 2018, 39(9):1665-1674.
SHI L Q, MA B, LI H Y, et al.Modeling and experimental validation of drag torque of wet multi-disk clutch with spline connected restriction in full speed range[J].Acta Armamentarii, 2018, 39(9):1665-1674. (in Chinese)
[15］ WANG P, KATOPODES N, FUJII Y. Statistical modeling of plate clearance distribution for wet clutch drag analysis [J]. SAE International Journal of Passenger Cars Mechanical Systems, 2018, 11(1):76-88.
[16］ NEUPERT T, BARTEL D. High-resolution 3D CFD multiphase simulation of the flow and the drag torque of wet clutch discs considering free surfaces[J].Tribology International, 2019, 129:283-296.
[17］ NEUPERT T, BARTEL D. Measurement of pressure distribution and hydrodynamic axial forces of wet clutch discs [J]. Tribology International, 2021, 163:107172.
[18］ ZHAO E H, MA B, LI H Y. Numerical and experimental studies on tribological behaviors of Cu-based friction pairs from hydrodynamic to boundary lubrication [J]. Tribology Transactions, 2017, 61(2):347-356.
[19］ YU L, MA B, CHEN M, et al. Thermodynamic differences of different friction pairs in a multidisc clutch caused by spline friction: numerical simulation and experimental verification [J]. Tribology Transactions, 2019, 62(4):724-736.
[20］ LANKARANI H M, NIKRAVESH P E. A contact force model with hysteresis damping for impact analysis of multibody systems [J]. Journal of Mechanical Design, 1990, 112(3):369-376.