Identification of Thread Connection Parameters of Projectile-fuze System Based on Thin-layer Element Method

doi:10.3969/j.issn.1000-1093.2020.07.005

Abstract

Abstract: Thread connection is one of the main forms of connection between penetrating projectile and fuze body. To address the problem that thread connection can not be represented accurately by way of the existing dynamic numerical analysis, a method of simulating the thread connection using thin-layer elements is proposed, and a method for identifying the material parameters of thin-layer element based on test results is established. Modal test of pipe threads was carried out. The influences of the amplitude of excitation force and the loose and tight connection of threads on the modal frequency and frequency response curve are discussed, and the thin-layer element method is used for the simulation calculation of pipe threads. Results show that the state of loose thread connection is much more affected by non-linear factors compeared with tight connection; the magnitude of excitation force exerts greater influence on the measured result of loosely connected threads; the maximum error of modal frequency is reduced from 26.66% to 1.35% by comparing the simulated results of thin-layer element with the fixed nodes. Key

Key words: projectile-fuzesystem, thin-layerelement, threadconnection, parameteridentification

CLC Number:

TJ02

YAN A'min， WANG Xiaofeng， WANG Jian, PI Aiguo， HUANG Fenglei. Identification of Thread Connection Parameters of Projectile-fuze System Based on Thin-layer Element Method[J]. Acta Armamentarii, 2020, 41(7): 1288-1298.

References

［1］ IBRAHIM R A, PETTIT C L. Uncertainties and dynamic problems of bolted joints and other fasteners[J]. Journal of Sound and Vibration, 2005, 279(3): 857-936.
[2] MACKERLE J. Finite element analysis of fastening and joining: a bibliography (1990—2002)[J]. International Journal of Pressure Vessels and Piping, 2003, 80(4): 253-271.
[3] CHAABAN A, MUZZO U. Finite element analysis of residual stresses in threaded end closures[J]. Journal of Pressure Vessel Technology,1991, 113(3):398-401.
[4] CHEN J J, SHIH Y S. A study of the helical effect on the thread connection by three dimensional finite element analysis[J]. Nuclear Engineering and Design, 1999, 191(2): 109-116.
[5] ZHANG D M, GAO S Q, NIU S H, et al. Study on collision of threaded connection during impact[J]. International Journal of Impact Engineering, 2017, 106:133-145.
[6] BRUTTI C, SALVINI P. Dynamic behaviour of tubular threaded joints[C]∥Proceedings of the 2nd International Offshore and Polar Engineering Conference. San Francisco, CA, US: International Society of Offshore and Polar Engineers, 1992:306-311.
[7] DESAI C S. Thin-layer element for interfaces and joints[J]. International Journal for Numerical and Analytical Methods in Geomech, 1984, 8(1):19-43.
[8] BOGRAD S, REUSS P, SCHMIDT A, et al. Modeling the dynamics of mechanical joints[J]. Mechanical Systems and Signal Processing, 2011, 25(8): 2801-2826.
[9] IRANZAD M, AHMADIAN H. Identification of nonlinear bolted lap joint models[J]. Computers & Structures, 2012, 96/97:1-8.

[10] 姜东, 吴邵庆, 史勤丰, 等. 基于各向同性本构关系薄层单元的螺栓连接参数识别[J]. 振动与冲击, 2014, 33(22): 35-40.
JIANG D, WU S Q, SHI Q F , et al. Parameter identification of bolted-joint based on the model with thin-layer elements with isotropic constitutive relationship[J]. Journal of Vibration and Shock, 2014, 33(22): 35-40.(in Chinese)
[11] ZHAO G, XIONG Z, JIN X, et al. Prediction of contact stiffness in bolted interface with natural frequency experiment and FE analysis[J]. Tribology International, 2018, 127:157-164.
[12] ADEL F, SHOKROLLAHI S, JAMAL-OMIDI M, et al. A model updating method for hybrid composite/aluminum bolted joints using modal test data[J]. Journal of Sound and Vibration, 2017, 396:172-185.
[13] LOTHAR G, ANDR S. Finite element simulation and experiments on rotor damping assembled by disc shrink fits[J]. Mechanical Systems and Signal Processing, 2019, 127: 412-422.
[14] ALAMDARI M M, LI J C, SAMALI B, et al. Nonlinear joint model updating in assembled structures[J]. Journal of Engineering Mechanics, 2013, 140(7): 04014042.
[15] 田晶, 路闯, 艾延廷, 等. 边界条件模拟方法对模态分析影响的研究[J]. 科学技术与工程, 2013, 13(34): 10417-10420.
TIAN J, LU C, AI Y T,et al. Study on the effects of simulation method of condition boundary on modal analysis[J]. Science Technology and Engineering, 2013, 13(34):10417-10420.(in Chinese)
[16] ION C M, GILBERT R G, NUNO M M. A method for an accurate estimation of natural frequencies using swept-sine acoustic excitation[J]. Mechanical Systems and Signal Processing,2019,116:693-709.
[17] SHOKROLLAHI S, ADEL F. Finite element model updating of bolted lap joints implementing identification of joint affected region parameters[J]. Journal of Theoretical and Applied Vibration and Acoustics, 2016, 2(1): 65-78.
[18] NARAYANASWAMY O S. Processing nonlinear multipoint constraints in the finite element method[J]. International Journal for Numerical Methods in Engineering, 1985, 21(7):1283-1288.
[19] MEGHLAT E M, OUDJENE M, AIT-AIDER H, et al. A new approach to model nailed and screwed timber joints using the finite element method[J]. Construction and Building Materials, 2013, 41:263-269.
[20] ZHANG Y Q. The application of contact element in finite element analysis[J]. Applied Mechanics and Materials, 2013, 422: 100-104.
[21] ZHANG D M, GAO S Q, XU X. A new computational method for threaded connection stiffness[J]. Advances in Mechanical Engineering, 2016, 8(12): 1-9.

第41卷第7期2020 年7月
兵工学报ACTA ARMAMENTARII
Vol.41No.7Jul.2020

[1]	LIU Zhongyong, GUO Jing, FAN Tao, BIAN Yuanjun, MENG Liu, ZHANG Huixuan, WEN Xuhui. A High-Performance Sensorless Control Strategy Using a Permanent Magnet Synchronous Generator [J]. Acta Armamentarii, 2022, 43(11): 2761-2762.
[2]	YAN Amin， PI Aiguo， WANG Jian， HUANG Fenglei， WANG Xiaofeng. The Method for Determining the Threaded Connection Parameters of Projectile-fuze System Based on Thin-layer Element Model [J]. Acta Armamentarii, 2021, 42(4): 743-754.
[3]	MENG Liu, ZHANG Huixuan, FAN Tao. Standstill Parameter Identification of Permanent Magnet Synchronous Motor and Parameter Auto-tuning Method of Current LoopController [J]. Acta Armamentarii, 2021, 42(10): 2114-2122.
[4]	LIN Tong， QIAN Linfang， FU Jiawei， WANG Mingming. Parameter Identification and Sensitivity analysis of Gun Elevating Equilibrator [J]. Acta Armamentarii, 2020, 41(9): 1736-1744.
[5]	YU Lei， ZHANG Yongli， YUAN Mengdi， LIU Ruiqing. A Time-varying Modal Parameter Recursive Estimation Method Based on FS-TARMA Model for Missile and Rocket [J]. Acta Armamentarii, 2020, 41(11): 2189-2197.
[6]	CHU Shixin， MAO Yunsheng， DONG Zaopeng， YANG Xin. Parameter Identification of High-speed USV Maneuvering Response Model Based on Maximum Likelihood Algorithm [J]. Acta Armamentarii, 2020, 41(1): 127-134.
[7]	DING Chuan-jun, ZHANG Xiang-yan, LIU Ning. Adaptive Unscented Kalman Filter Algorithm for Identifying and Analyzing the Dynamic Response Model Parameters of StrandedWire Helical Springs [J]. Acta Armamentarii, 2018, 39(1): 28-37.
[8]	ZHAO Qiang-qiang, HOU Bao-lin. Identification of Interval Uncertainty Parameters of a Howitzer Shell Transfer Arm [J]. Acta Armamentarii, 2017, 38(1): 35-42.