Theoretical Model and Numerical Study of Shaped Charge Jet Penetrating into Thick Moving Target

doi:10.3969/j.issn.1000-1093.2019.08.001

Abstract

Abstract: An attack mode using shaped charge jet is proposed to effectively intercept and destroy the incoming high-speed missiles and earth-penetrating projectiles with large wall thickness. Based on virtual origin theory, an infinitesimal method is used to divide the interaction process of shaped charge jet and thick moving target into two stages: undisturbed jet penetration and disturbed jet penetration. At the undisturbed jet penetration stage, the jet is not be disturbed by lateral force on target plate. The penetration depth contributed by undistributed jet and the aperture of cavity were analyzed. At the disturbed jet penetration stage, the jet is disturbed by lateral force on target plate. The models of lateral drift velocity and penetration depth of distributed jet were established. A 40 mm-diameter shaped charge was designed to verify the theoretical model. The penetration depth of jet penetrating into steel target at the transverse velocity of 0-600 m/s was calculated using the LS-DYNA software. The theoretical results of the proposed model were compared with the experimental data in Ref.\[17\]. The results indicate that the shaped charge warhead is an effective means to strike high speed moving target. The higher the moving speed of target is, the shorter the elapsed time at the undisturbed jet penetration stage is, the more the interference of jet is, and the smaller the penetration depth is. Key

Key words: shapedchargejet, movingtarget, penetrationdepth, thickwall, virtualorigin, numericalsimulation

CLC Number:

TJ410.3⁺33

JIA Xin, HUANG Zhengxiang， XU Mengwen， XIAO Qiangqiang. Theoretical Model and Numerical Study of Shaped Charge Jet Penetrating into Thick Moving Target[J]. Acta Armamentarii, 2019, 40(8): 1553-1561.

References

［1］ SHAHRAINI M T. Casing toughness effect on anti-air fragmentation warhead performance[C]∥Proceedings of the 23rd International Symposium on Ballistics. Tarragona, Spain：International Ballistics Committee, 2007: 209-213.
[2］ WAGGENER S. Relative performance of anti-air missile warheads[C]∥Proceedings of the 19th International Symposium on Ballistics. Interlaken, Switzerland: International Ballistics Committee, 2001：623-630.
[3］ LIU T, QIAN L X, ZHANG S Q. Study on fragment focusing mode of air-defense missile warhead[J]. Propellants, Explosives, Pyrotechnics, 1998, 23(5):240-243.
[4］ HELD M. Aimable fragmenting warhead[C]∥Proceedings of the 13rd International Symposium on Ballistics. Stockholm, Sweden: International Ballistics Committee, 1992：539-548.
[5］ PUGH E M, EICHELBERGER R J, ROSTOKER N. Theory of jet formation by charges with lined conical cavities[J]. Journal of Applied Physics, 1952, 23(5): 532-536.
[6］ EICHELBERGER R J, PUGH E M. Experimental verification of the theory of jet formation by charges with lined conical cavities[J]. Journal of Applied Physics, 1952, 23(5): 537-542.
[7］ WALTERS W P, ZUKAS J A. Fundamentals of shaped charges[M].New York,NY，US：John Wiley & Sons, 1989：25-50.
[8］ WALTERS W. A brief history of shaped charges: RP-232 [R]. Adelphi, MD , US：Army Research Laboratory , 2008:35-60.
[9］李燕青, 高飞, 王长兴, 等. 一种新型防护装甲干扰射流的工程算法[J]. 兵工学报，2002, 23(4): 546-550.
LI Y Q, GAO F, WANG C X, et al. Engineering algorithm for a new type of protective armor disturbing jet penetration[J]. Acta Armamentarii, 2002, 23(4): 546-550.(in Chinese)

[10］张先锋，丁建宝，赵晓宁. 夹层聚能装药作用过程的数值模拟[J].爆炸与冲击, 2009, 29(6)：618-624.
ZHANG X F, DING J B, ZHAO X N. Numerical simulation of double layer shaped charge[J]. Explosion and Shock Waves, 2009, 29(6)：618-624. (in Chinese)
[11］朱定波, 李景云, 李德君. 爆炸装甲对破甲射流干扰机理的研究[J]. 兵工学报，1991, 13(1): 46-53.
ZHU D B, LI J Y, LI D J. Disturbance on an armor-piercing jet caused by an explosive armor[J]. Acta Armamentarii, 1991, 13(1): 46-53. (in Chinese)
[12］贾鑫, 黄正祥, 祖旭东, 等. 聚能装药垂直侵彻橡胶复合装甲的变形研究[J]. 工程力学，2013, 30(2): 451-457.
JIA X, HUANG Z X, ZU X D, et al. Research on deformation for the rubber composite armor against shaped charge vertical penetration[J]. Engineering Mechanics, 2013, 30(2): 451-457.(in Chinese)
[13］ YADAV H S. Study of jet interaction with interlayer material of bulging armor[J]. Propellants, Explosives, Pyrotechnics, 2004, 29(6): 349-353
[14］ JIA X, HUANG Z X, ZU X D, et al. Theoretical analysis of the disturbance of shaped charge jet penetrating a woven fabric rubber composite armor[J]. International Journal of Impact Engineering, 2014, 65: 69-78.
[15］ MAYSELESS M, MARMOR E, GOV N, et al. Interaction or a shaped charge jet with reactive or passive cassettes[C]∥Proceedings of the 14th International Symposium on Ballistics. Quebec, Canada: International Ballistics Committee, 1993: 439- 448.
[16］ LUTTWAK G, LUTTWAK A. Moving plate perforation analytic model and numerical simulation[C]∥Proceedings of the 21st International Symposium on Ballistics. Adelaide, Australia: International Ballistics Committee, 2004：976-983.
[17］ MARMOR E, ME-BAR Y, MAYSELESS M,et al. A model for calculating the penetration of an overflying-top-attack jet into a moving target[C]∥Proceedings of the 12nd International Symposium on Ballistics. San Antonio, TX, US: International Ballistics Committee,1990: 10-19.
[18］陈振华, 张国伟, 高元浩, 等. JPC 对不同角度的移动靶板的侵彻数值模拟[J]. 机电技术, 2014, 12(6): 54-56.
CHEN Z H, ZHANG G W, GAO Y H, et al. Penetration numerical simulation of JPC for moving target with different angles[J]. Electromechanical Technology, 2014,12(6): 54-56. (in Chinese)
[19］陈振华, 张国伟, 高元浩, 等. 仿真分析三种射流形态对移动靶板的侵彻[J]. 弹箭与制导学报, 2015, 35(4): 70-72.
CHEN Z H, ZHANG G W, GAO Y H, et al. Numerical simulation of penetration of three types of shaped charge jet in moving oblique target[J]. Journal of Projectile, Rockets, Missile and Guidance, 2015, 35(4): 70-72. (in Chinese)
[20］王静, 王成, 宁建国. 聚能射流侵彻的理论模型与孔径计算[J]. 工程力学, 2009, 26(4): 21-26.
WANG J, WANG C, NING J G. Theoretical model for shaped charge jets penetration and cavity radius calculation[J]. Engineering Mechanics, 2009, 26(4): 21-26. (in Chinese)
[21］肖强强. 聚能装药对典型土壤/混凝土复合介质目标的侵彻研究[D]. 南京: 南京理工大学, 2012：15-22.
XIAO Q Q. Penetration research of shaped charge into typical soil/concrete target[D]. Nanjing:Nanjing University of Science and Technology, 2012：15-22. (in Chinese)
[22］黄正祥. 聚能装药理论与实践[M]. 北京：北京理工大学出版社, 2014： 65-75.
HUANG Z X. Theory and practice of shaped charge[M]. Beijing: Beijing Institute of Technology Press, 2014：65-75. (in Chinese)
[23］ SZENDREI T. Analytical model of crater formation by jet impact and its application to calculation of penetration curves and hold profiles[C]∥Proceedings of the 7th International Symposium on Ballistics. Hague, the Netherlands：International Ballistics Committee, 1983：575-583.
[24］ HELD M. Verification of the equation for radial crater growth by shaped jet penetration[J]. International Journal of Impact Engineering, 1995, 17(1/2/3): 387-398.
[25］ LI W B, WANG X M, LI W B.The effect of annular multi-point initiation on the formation and penetration of an explosively formed penetrator[J]. International Journal of Impact Engineering, 2010, 37(4)：414-424.
[26］朱传胜. 带隔板爆炸成型弹丸战斗部成型技术研究[D]. 南京：南京理工大学, 2014：49-50.
ZHU C S. Technology research on the formation of explosively formed projectile warhead with wave shaper[D]. Nanjing：Nanjing University of Science and Technology, 2014：49-50. (in Chinese)
[27］ Livermore Software Technology Corporation. LS-DYNA keyword user’s manual: Version 970 [M]. Livermore, CA,US: Livermore Software Technology Corporation, 2003.
[28］王儒策，赵国志. 弹丸终点效应[M].北京：北京理工大学出版社,1993：229-234.
WANG R C, ZHAO G Z. Projectile terminal effect[M]. Beijing: Beijing Institute of Technology Press, 1993：229-234. (in Chinese)

第40卷
第8期2019 年8月兵工学报ACTA
ARMAMENTARIIVol.40No.8Aug.2019

[1]	YAN Zechen, YUE Songlin, QIU Yanyu, WANG Jianping, ZHAO Yuetang, SHI Jie, LI Xu. Improvement on the Calculation Method for Reflected Pressure of Shock Wave in Underwater Explosion [J]. Acta Armamentarii, 2024, 45(4): 1196-1207.
[2]	HE Jiawei, ZHAI Junyi, GAO Weipeng, LI Ye. Numerical Simulation of Flow Characteristics of the Underwater Vehicle with a Cylindrical Structure Based onDifferent Turbulence Models [J]. Acta Armamentarii, 2022, 43(S2): 53-63.
[3]	WANG Ge， ZHANG Chun， LIN Zhiwei， WANG Baohua， TAN Hu， CHEN Chen. Research on's Opening Distance of AHEAD Ammunition [J]. Acta Armamentarii, 2022, 43(S1): 115-120.
[4]	XU Hui, HUANG Chenlei, WANG Xikuo, LIU Kun, LI Zhongxin, WU Zhilin. Theoretical and Experimental Study of Projectile Dynamic Engraving Resistance [J]. Acta Armamentarii, 2022, 43(9): 2263-2273.
[5]	WANG Xiaodong, XU Yongjie, DONG Fangdong, WANG Hao, ZHENG Nana. Numerical Simulation of Penetration Resistance of Kevlar and Ceramic Composite Structures [J]. Acta Armamentarii, 2022, 43(9): 2360-2366.
[6]	WANG Jianmin, CHEN Kuijun, LI Tonghua, LI Guanhua, FAN Zhuangqing, ZHANG Jieyuan, CHEN Bin, YANG Guangming, KANG Jianyi, CHEN Jing, DUAN Zhaoxia, CAO Lingyu, WANG Han. Assessment Method for Probability of Occurance of Different Injury Severities in Personnel Based on Fragment Penetration Depth [J]. Acta Armamentarii, 2022, 43(9): 2086-2100.
[7]	GUAN Dian， GUO Yawen， LI Shipeng， TANG Jianing， WANG Ningfei. Influence of Gas-particle Two-phase Flow on Ignition of the Solid Rocket Motor under Lateral Acceleration [J]. Acta Armamentarii, 2022, 43(8): 1792-1807.
[8]	GAO Yueguang, FENG Shunshan, LIU Yunhui, HUANG Qi. Initial Velocity Distribution of Fragments from Cylindrical Charge Shells with Different Thick End Caps [J]. Acta Armamentarii, 2022, 43(7): 1527-1536.
[9]	L Dailong， CHEN Shaosong， XU Yihang， QIU Jiawei. Aerodynamic Characteristics of Close-coupled Canard Missile [J]. Acta Armamentarii, 2022, 43(6): 1316-1325.
[10]	WANG Danyu, NAN Fengqiang, LIAO Xin, XIAO Zhongliang, DU Ping, WANG Binbin. Effect of Flame Inhibitor of the Muzzle Flame of Large Caliber Gun [J]. Acta Armamentarii, 2022, 43(2): 273-278.
[11]	XU Gancheng, YUAN Weize, CHEN Linheng, LI Chengxue, XIE Xuhu, NIE Mengqi. Seismic Collapse Resitance of NFB700 High-strength Steel Plate [J]. Acta Armamentarii, 2022, 43(2): 391-400.
[12]	LU Kuan， RAO Xiang， WANG Huamei， ZHANG Qian. The Influences of Different Mooring Systems on the Hydrodynamic Performance of Buoy [J]. Acta Armamentarii, 2022, 43(1): 120-130.
[13]	CHENG Shenshen, TAO Ruyi, WANG Hao, XUE Shao, LIN Qingyu. Dampling Characteristics of Projectile in Engraving Process of Nylon Sealing Band [J]. Acta Armamentarii, 2021, 42(9): 1847-1857.
[14]	GUAN Dian, LI Shipeng, LIU Zhu, WANG Ningfei. Influence of Lateral Acceleration on Ignition Transients of Solid Rocket Motor [J]. Acta Armamentarii, 2021, 42(9): 1877-1887.
[15]	WANG Danyu, NAN Fengqiang, LIAO Xin, XIAO Zhongliang, DU Ping, WANG Binbin. Characteristics of Muzzle Flow Field of Large Caliber Gun Considering Chemical Reaction [J]. Acta Armamentarii, 2021, 42(8): 1624-1630.