增强颗粒对切削SiCp/Al复合材料切屑形成过程的影响机理

doi:10.3969/j.issn.1000-1093.2019.01.024

兵工学报 ›› 2019, Vol. 40 ›› Issue (1): 208-218.doi: 10.3969/j.issn.1000-1093.2019.01.024

增强颗粒对切削SiCp/Al复合材料切屑形成过程的影响机理

段春争¹，刘玉敏²，孙伟¹，车明帆¹

（1.大连理工大学机械工程学院, 辽宁大连 116024; 2.漯河职业技术学院机电工程系, 河南漯河 462000）

收稿日期:2018-04-09 修回日期:2018-04-09 上线日期:2019-03-12
作者简介:段春争(1970—), 男, 副教授, 博士生导师。E-mail: duancz@dlut.edu.cn
基金资助:
国家自然科学基金项目（51775083）

Influence of Reinforced Particles on Chip Formation Process in Cutting SiCp/Al Metal Matrix Composites

DUAN Chunzheng¹， LIU Yumin²， SUN Wei¹， CHE Mingfan¹

(1.School of Mechanical Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China; 2.Department of Electro-machinery Engineering, Luohe Vocational Technology College, Luohe 462000, Henan, China)

Received:2018-04-09 Revised:2018-04-09 Online:2019-03-12

摘要/Abstract

摘要： 为研究SiC颗粒对SiCp/Al复合材料切屑形成过程的影响，设计了一种新型弹簧式快速落刀装置。通过正交切削试验获得切屑和切屑根部，观察其形态及金相显微组织，分析SiC颗粒沿剪切带的排列机制、颗粒的断裂与破碎机理、裂纹的扩展及其对切屑形成的影响。结果表明：设计的快速落刀装置加速度大，能获取有效的切屑根部；基体塑性滑移对颗粒产生的力和力矩使得颗粒沿剪切带排列；颗粒的断裂与破碎主要发生在剪切区、工件与切屑分离面、第2变形区以及刀尖附近的已加工表面；微裂纹从自由表面和剪切区内部沿剪切面扩展；裂纹沿剪切面扩展使得切屑受力不平衡，切屑加速流出，同时裂纹两侧沿剪切面发生相对滑动，导致切屑呈不规则锯齿形。

关键词: SiCp/Al复合材料, 快速落刀装置, 颗粒排列, 颗粒断裂, 裂纹扩展, 切屑形成

Abstract: A spring-loaded quick-stop device was designed to investigate the influence of SiC particles on the chip formation process of SiCp/Al composites. The chips and their roots are obtained by orthogonal cutting test, and their morphology and microstructure are observed. The arrangement mechanism of SiC particles along shear band, the fracture and breaking mechanisms of particles, the crack propagation and its influence on chip formation are analyzed. The results show that the acceleration of quick-stop device is large, which means that the chip roots obtained are effective, the force and torque generated by plastic sliding of matrix cause the particles to be arranged along the shear band, and the fractures of particles mainly occur in the shear zones, the separated surface of workpeice and chip, the second deformation zone and the machined surface near the tool nose. The microcracks initiating from the outside free surface and the interior of shear zone propagate along the shear plane. As the cracks propagate along the shear plane, the force applied on chips is unbalanced, which causes the chips to outflow fleetly, and the relative sliding of both sides of the cracks along the shear plane leads to the formation of irregular saw-tooth chips. Key

Key words: SiCp/Almetalmatrixcomposite, quick-stopdevice, particlesarrangement, particlefracture, crackpropagation, chipformation

中图分类号:

TG501.1

段春争，刘玉敏，孙伟，车明帆. 增强颗粒对切削SiCp/Al复合材料切屑形成过程的影响机理[J]. 兵工学报, 2019, 40(1): 208-218.

DUAN Chunzheng， LIU Yumin， SUN Wei， CHE Mingfan. Influence of Reinforced Particles on Chip Formation Process in Cutting SiCp/Al Metal Matrix Composites[J]. Acta Armamentarii, 2019, 40(1): 208-218.

参考文献

［1］ SEKHAR R, SINGH T P. Mechanisms in turning of metal matrix composites: a review[J]. Journal of Materials Research and Technology, 2015, 4(2): 197-207.
[2］ DANDEKAR C R, SHIN Y C. Modeling of machining of compo-site materials: a review[J]. International Journal of Machine Tools and Manufacture, 2012, 57(2): 102-121.
[3］刘晓, 陈吉朋, 顾琳,等. 50%SiCp/Al复合材料的电弧铣削与铣磨组合加工[J]. 上海交通大学学报, 2018, 52(2):222-227.
LIU X, CHEN J P, GU L, et al. Combined machining of 50% SiCp/Al composites with electrical-arc-milling and milling-grinding[J]. Journal of Shanghai Jiao Tong University, 2018, 52(2):222-227. (in Chinese)
[4］ MUTHUKRISHNAN N, MURUGAN M, RAO K P. Machinability issues in turning of Al-SiC (10p) metal matrix composites[J]. International Journal of Advanced Manufacturing Technology, 2008, 39(3/4): 211-218.
[5］ MUTHUKRISHNAN N, MURUGAN M, RAO K P. An investigation on the machinability of Al-SiC metal matrix composites using pcd inserts[J]. International Journal of Advanced Manufacturing Technology, 2008, 38(5/6):447-454.
[6］ ZHOU L, WANG Y, MA Z Y, et al. Finite element and experimental studies of the formation mechanism of edge defects during machining of SiCp/Al composites[J]. International Journal of Machine Tools and Manufacture, 2014, 84(6): 9-16.
[7］ WANG B B, XIE L J, WANG X B, et al. Simulation studies of the cutting process on SiCp/Al composites with different volume fraction of reinforced SiC particles[C]∥Proceedings of the International Conference on High Speed Machining. Harbin, China: Trans Tech Publications Ltd., 2014: 321-326.
[8］ EL-GALLAB M, SKLAD M. Machining of Al/SiC particulate metal matrix composites—part II: workpiece surface integrity[J]. Journal of Materials Processing Technology， 1998, 83(1/2/3): 277-285.
[9］ JOSHI S S, RAMAKRISHNAN N, RAMAKRISHNAN P. Micro-structural analysis of chip formation during orthogonal machining of Al/SiCp composites[J]. Journal of Engineering Materials and Technology, 2001, 123(3): 315-321.

[10］ QUAN Y M, ZHOU Z H, YE B Y. Cutting process and chip appearance of aluminum matrix composites reinforced by SiC particle[J]. Journal of Materials Processing Technology, 1999, 91(1): 231-235.
[11］葛英飞，徐九华，杨辉. SiCp/Al复合材料超精密车削切屑形成机制及形成过程模型[J]. 兵工学报, 2015, 36(5): 911-920.
GE Y F, XU J H, YANG H. Chip formation mechanisms and the process model during ultra-precision turning of SiCp/Al composite[J]. Acta Armamentarii, 2015, 36(5):911-920.(in Chinese)
[12］ LIN J T, BHATTACHARYYA D, FERGUSON W G. Chip formation in the machining of SiC-particle-reinforced aluminium-matrix composites[J]. Composites Science & Technology, 1998, 58(2): 285-291.
[13］王恒厂, 李灿, 郁思佳, 等. 车床快速落刀装置研究[J]. 机械设计与制造工程, 2016, 45(1): 63-65.
WANG H C, LI C, YU S J, et al. Research on a quick-stop device in lathe[J]. Machine Design and Manufacturing Enginee-ring, 2016, 45(1):63-65. (in Chinese)
[14］ IULIANO L, SETTINERI L, GATTO A. High-speed turning experiments on metal matrix composites[J]. Composites Part A：Applied Science and Manufacturing, 1998, 29(12): 1501-1509.
[15］ FATHIPOUR M, HAMEDI M, YOUSEFI R. Numerical and experimental analysis of machining of Al (20 vol% SiC) composite by the use of ABAQUS software[J]. Materialwissenschaft und Werkstofftechnik, 2013, 44(1): 14-20.
[16］ PRAMANIK A, ZHANG L C, ARSECULARATNE J A. An FEM investigation into the behavior of metal matrix composites: tool-particle interaction during orthogonal cutting[J]. International Journal of Machine Tools and Manufacture, 2007, 47(10): 1497-1506.
[17］全燕鸣，周泽华. 硬脆颗粒增强金属基复合材料切削区的变形[J]. 华南理工大学学报(自然科学版), 1998, 26(4): 28-33.
QUAN Y M, ZHOU Z H. Deformation of cutting zone of the hard particle-reinforced metal matrix composites[J]. Journal of South China University of Technology（Natural Science）, 1998, 26(4): 28-33. (in Chinese)
[18］陆正杰. 车削高体积分数SiCp/Al复合材料有限元仿真与实验研究[J]. 机械设计与研究, 2017, 33(5):156-159.
LU Z J.Finite element simulation and experiment research of turning SiCp/Al composites with high volume fraction[J]. Machine Design and Research, 2017, 33(5):156-159. (in Chinese)
[19］ LIU L F, DAI L H, YANG G W. Strain gradient effects on deformation strengthening behavior of particle reinforced metal matrix composites[J]. Materials Science & Engineering A, 2003, 345(1):190-196.

第40卷第1期
2019 年1月兵工学报ACTA
ARMAMENTARIIVol.40No.1Jan.2019

[1]	杨硕, 杜天玮, 张晓鹏, 马梁, 张桂昌. 外物损伤对叶片振动疲劳裂纹扩展性能的影响[J]. 兵工学报, 2023, 44(6): 1713-1721.
[2]	高峰，张泽. 含装药缺陷的固体火箭发动机性能评估综述[J]. 兵工学报, 2021, 42(8): 1789-1802.
[3]	张晓颖，李胜杰，李志强. 爆炸载荷作用下夹层玻璃动态响应的数值模拟[J]. 兵工学报, 2018, 39(7): 1379-1388.
[4]	苗润，王伟力，宋杨. TC4钛合金动态II型裂纹扩展速度与加载速度的关系研究[J]. 兵工学报, 2016, 37(12): 2331-2339.
[5]	葛英飞，徐九华，杨辉. SiC_p/Al复合材料超精密车削切屑形成机制及形成过程模型[J]. 兵工学报, 2015, 36(5): 911-920.
[6]	周清春，鞠玉涛，韦震，周长省. 端羟基聚丁二烯推进剂/衬层脱粘的断裂机理与断裂能获取研究[J]. 兵工学报, 2014, 35(7): 990-995.
[7]	高红俐,张立彬,姜伟,周寅. 电磁谐振式疲劳裂纹扩展试验固有频率跟踪系统[J]. 兵工学报, 2013, 34(7): 896-903.
[8]	陈吉生, 鄂大辛, 张敬文. 1Cr18Ni9Ti 管材拉伸断裂过程中裂纹扩展的研究[J]. 兵工学报, 2013, 34(7): 865-868.
[9]	李魁武, 宁变芳, 曾志银, 王在森, 张军岭. 基于裂纹形成及扩展的火炮闩体寿命研究[J]. 兵工学报, 2013, 34(3): 289-293.

增强颗粒对切削SiCp/Al复合材料切屑形成过程的影响机理

Influence of Reinforced Particles on Chip Formation Process in Cutting SiCp/Al Metal Matrix Composites

PDF

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 9

编辑推荐

Metrics

本文评价