某型柴油机活塞销轴承磨损分析及表面型线设计

doi:10.3969/j.issn.1000-1093.2018.10.003

摘要/Abstract

摘要： 针对某型柴油机活塞销轴承初始设计方案在试验中出现的磨损问题，开展了活塞换热分析及活塞温度场仿真与试验对标。在此基础上进行热机耦合变形分析，发现活塞销轴承变形不协调是导致此类问题的主要原因。针对活塞销孔轴承进行热机状态型线匹配分析，开展了活塞销孔轴承热机耦合状态下的型线优化设计，通过仿真及试验验证了该型线优化方案的有效性。分析了桶形型线、指数型线及超椭圆型线对连杆小头衬套轴承载荷分布状态的影响，3种型线对比结果表明，指数型线和超椭圆型线可有效地改善连杆小头轴承载荷分布状态。

关键词: 柴油机, 活塞销轴承, 磨损分析, 型线设计

Abstract: For the seizure failure of piston pin bearing in the preliminary structural design, the heat transfer of piston is simulated and its temperature field is calibrated, and the thermo-mechanical deformation of piston at state is analyzed. The analytic results show that the non-compatible deformation of piston pin bearing is main reason leading to wear. Accordingly, the profile matching of piston pin boss bearing under thermo-mechanical condition is presented. On this basis, the profile of piston pin boss bearing is optimized, and the optimized profile is validated by simulation and engine test. The barrel-shaped, exponential and hyperelliptic profiles of the connecting rod small end bearing are compared to investigate the influences of those profiles on the load distribution of the bush. Results show that exponential and hyperelliptic profiles are more suitable for improving the load distribution of the connecting rod small end bearing.Key

Key words: dieselengine, pistonpinbearing, wearanalysis, profiledesign

中图分类号:

TK422

张利敏，王根全，王延荣，赵志强，张忠伟，宋现浩. 某型柴油机活塞销轴承磨损分析及表面型线设计[J]. 兵工学报, 2018, 39(10): 1892-1900.

ZHANG Li-min, WANG Gen-quan, WANG Yan-rong, ZHAO Zhi-qiang, ZHANG Zhong-wei, SONG Xian-hao. Profile Design and Seizure Analysis of Piston Pin Bearing of a Diesel Engine[J]. Acta Armamentarii, 2018, 39(10): 1892-1900.

参考文献

［1］ Silva F S. Fatigue on engine pistons—a compendium of case studies［J］. Engineering Failure Analysis, 2006, 13(3):480-492.
［2］刘世英, 林风华, 秦有志，等. 销孔结构设计对活塞可靠性影响的研究［J］. 内燃机工程，2007, 28(1): 46-50.
LIU Shi-ying, LIN Feng-hua, QIN You-zhi, et al. Piston durability research based on the pin-bore profile design［J］. Chinese Internal Combustion Engine Engineering, 2007, 28(1): 46-50.(in Chinese)
［3］田小青, 刘世英, 张文利，等. 柴油机活塞异形销孔结构设计与疲劳试验的综合性研究［J］. 内燃机工程, 2008, 29(1): 52-55.
TIAN Xiao-qing, LIU Shi-ying, ZHANG Wen-li, et al. Design and experimental study of surface profile of diesel engine piston pin bore［J］. Chinese Internal Combustion Engine Engineering, 2008, 29(1): 52-55.(in Chinese)
［4］张利敏, 王延荣, 赵志强，等. 高功率密度柴油机连杆小头衬套孔结构优化设计［J］. 车用发动机, 2014 (2): 15-18.
ZHANG Li-min, WANG Yan-rong, ZHAO Zhi-qiang, et al. Optimization of bushing taper hole of connecting rod small end for HPD diesel engine［J］. Vehicle Engine, 2014 (2): 15-18. (in Chinese)
［5］张利敏, 卢士勇, 韩琦,等. 柴油机活塞销孔型线对比分析研究［J］. 车用发动机, 2017(3):78-81.
ZHANG Li-min, LU Shi-yong, HAN Qi, et al. Comparison of piston pin hole profiles for diesel engine［J］. Vehicle Engine, 2017(3): 78-81.(in Chinese)
［6］ Wroblewski E, Iskra A, Babiak M. Simulations geometrical structures of the stepped profile bearing surface of the piston［J］. Procedia Engineering, 2017, 192: 965-970.
［7］刘畅, 张卫正, 刘雨薇. 高强化柴油机活塞异形销孔结构设计与试验研究［J］. 车用发动机, 2011(5): 18-23.
LIU Chang, ZHANG Wei-zheng, LIU Yu-wei. Structural design and experimental study on piston non-cirular pinhole for highly-intensified diesel engine［J］. Vehicle Engine, 2011(5): 18-23.(in Chinese)
［8］ Tada Y, Nishihara S. Optimum shape design of contact surface with finite element method［J］. Advance in Engineering Software, 1993, 18(2): 75-85.
［9］ Suhara T, Ato S, Takiguchi M, et al. Friction and lubrication characteristics of piston pin boss bearings of an automotive engine, SAE Technical Paper 970840［R］. Detroit, MI, US: SAE, 1997.

［10］ Nishikawa C. Optimization of semi-floating piston pin boss formed by using oil-film simulations, SAE Technical Paper 2012-01-0908［R］. Detroit, MI, US: SAE, 2012.
［11］ Kohashi K I, Kimura Y, Murakami M, et al. Analysis of piston friction in internal combustion engine［J］. SAE International Journal of Fuels and Lubricants, 2013, 6(3):589-593.
［12］ Wang D C, Mian O, Merritt D, et al. Elasto-hydrodynamic lubrication analysis and wear prediction of connecting rod small-end bush and piston pin interface, SAE Technical Paper 2008-36-0068［R］. Detroit, MI, US: SAE, 2008.
［13］刘宽伟, 左正兴, 向建华. 全浮式活塞销运动特性研究［J］. 内燃机工程, 2016, 37(4): 155-160.
LIU Kuan-wei, ZUO Zheng-xing, XIANG Jian-hua. Study on movement characteristics of floating piston pin［J］. Chinese Internal Combustion Engine Engineering, 2016, 37(4): 155-160.(in Chinese)
［14］楼狄明, 张志颖, 王礼丽. 机车柴油机组合活塞的换热边界条件及热负荷［J］. 同济大学学报：自然科学版, 2005, 33(5): 664-667.
LOU Di-ming, ZHANG Zhi-ying, WANG Li-li. Heat transfer boundary condition and thermal load of combined-piston for locomotive diesel engines［J］. Journal of Tongji University:Natural Science, 2005, 33(5): 664-667.(in Chinese)
［15］赵镇南. 传热学［M］. 第2版. 北京: 高等教育出版社, 2008.
ZHAO Zhen-nan. Heat transfer［M］. 2nd ed. Beijing: Higher Education Press, 2008. (in Chinese)
［16］ Matthieu D, Cezar T, Vincent C. Optimization of contact profiles using super-ellipse［J］. SAE International Journal of Materials and Manufacturing, 2017, 10(2): 234-244.

第39卷
第10期2018 年10月兵工学报ACTA
ARMAMENTARIIVol.39No.10Oct.2018

[1]	李子铭, 刘振明, 刘景斌, 陈萍. 舰船柴油机微通道内燃油空化现象的模型对比[J]. 兵工学报, 2023, 44(10): 3091-3100.
[2]	黎一锴，彭靖，史中杰，檀丽宏，李耀宗. 具有环境适应性的柴油机最小压缩比设计方法[J]. 兵工学报, 2022, 43(8): 1744-1752.
[3]	郭圣刚，王建平，赵忠诚，程晶晶，田新伟. 金属掺杂对高强化柴油机活塞销类金刚石薄膜涂层摩擦学性能的影响[J]. 兵工学报, 2021, 42(4): 715-722.
[4]	于飞，刘波澜，颜超，韩耀辉，王文泰. 柴油机电动可变气门正时机构特性[J]. 兵工学报, 2021, 42(3): 468-477.
[5]	顾程，乔新勇，韩立军. 不同燃油对某重型柴油机燃烧稳定性影响分析[J]. 兵工学报, 2020, 41(3): 426-433.
[6]	强永平，李海鹰，张晓琴，蔡忠周，朱伟青，李玉峰，龚永星. 柴油机回水温度对燃烧过程影响试验研究[J]. 兵工学报, 2020, 41(2): 222-230.
[7]	赵建华，应宇辰，郭成豹. 柴油机磁场的计算、试验与消磁优化[J]. 兵工学报, 2020, 41(2): 350-355.
[8]	李佳蔚，崔涛，刘宇航，师帅楠，孙强. 基于排气温度动态模型的在线观测器研究[J]. 兵工学报, 2019, 40(8): 1562-1571.
[9]	王子玉，张岩，王雷，刘金龙，白洪林，李玉峰. 进气门晚关米勒循环对高强化柴油机燃烧和换气影响的研究[J]. 兵工学报, 2019, 40(1): 8-17.
[10]	王旭东，熊春华，鲁长波，安高军，王锋. 高原环境下柴油机燃用聚醚型含氧燃料热平衡试验研究[J]. 兵工学报, 2018, 39(8): 1473-1478.
[11]	刘永丰，王龙飞，刘胜，尹玉婷，杨震寰. 海拔高度对柴油机缸内热流分布影响规律研究[J]. 兵工学报, 2018, 39(6): 1049-1057.
[12]	刘宇航，张付军，高宏力，王苏飞. 对置活塞二冲程柴油机新鲜充量短路研究[J]. 兵工学报, 2018, 39(6): 1058-1065.
[13]	刘宇航，张付军，慕连好，高宏力，王苏飞. 对置活塞二冲程柴油机换气子阶段完成比例研究[J]. 兵工学报, 2018, 39(3): 428-435.
[14]	谭丕强，王德源，王成官，李远，楼狄明，李云广，刘胜，杨振寰. 高原环境下重型柴油机的性能优化研究[J]. 兵工学报, 2018, 39(3): 436-443.
[15]	赵文柱，王宪成，赵永东，孙志新，徐冬冬. 耦合内部流动的喷孔积碳对柴油机喷雾影响研究[J]. 兵工学报, 2018, 39(2): 217-223.