基于快速抛光技术的光学元件材料去除模型研究

doi:10.3969/j.issn.1000-1093.2017.03.015

兵工学报 ›› 2017, Vol. 38 ›› Issue (3): 527-533.doi: 10.3969/j.issn.1000-1093.2017.03.015

基于快速抛光技术的光学元件材料去除模型研究

林涛¹, 杨炜¹, 王健²

（1.厦门大学航空航天学院，福建厦门 361005; 2.中国工程物理研究院激光聚变研究中心，四川绵阳 621900）

收稿日期:2016-04-22 修回日期:2016-04-22 上线日期:2017-04-24
作者简介:林涛（1989—），男，硕士研究生。E-mail: 519023733@qq.com
基金资助:
国家自然科学基金项目（51675453）；福建省高等学校创新能力提升计划项目（2013年）

Research on Material Removal Model of Optical Elements Based on Fast Polishing Technology

LIN Tao¹, YANG Wei¹, WANG Jian²

(1.School of Aerospace Engineering, Xiamen University, Xiamen 361005, Fujian, China; 2.Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900, Sichuan, China)

Received:2016-04-22 Revised:2016-04-22 Online:2017-04-24

摘要/Abstract

摘要： 为精确控制抛光阶段材料去除，实现光学元件的确定性抛光加工，在分析快速抛光原理和快速抛光材料去除机制基础上，从单颗磨粒受力和抛光垫峰点捕获的磨粒数出发，获得量化的单颗磨粒瞬时切除体积和抛光接触区参与有效磨粒数，从而建立一种光学元件快速抛光材料去除模型。研究结果表明：以材料去除量为实验对象，在不同抛光液、抛光垫和光学元件实验条件下，材料去除模型的理论预测结果与实验结果较为吻合,材料去除量误差可以控制在9%以内。验证了该模型对于光学元件快速抛光技术的适用性，从而可以确定性的控制快速抛光时间和效率。

关键词: 机械制造工艺与设备, 光学元件, 快速抛光, 材料去除模型

Abstract: In order to accurately control the material removal in polishing stage, and achieve the deterministic polishing processing of toptical element, the quantitative mean volume removed by a single particles per unit time and the number of the active particles on the wafer-pad interface are obtained from the force applied on an abrasive particle and the number of all particles on the wafer-pad contact area. An optical element fast polishing material removal model is established based on the analysis of fast polishing principle and fast polishing material removal mechanism. Research shows that, under the experimental conditions of different polishing liquids, polishing pads and optical elements, the theoretically predicted results of the material removal model are well coincident with the experimental results, and the error of material removal can be controlled within 9%. The proposed model is verified to be suitable for the optical element fast polishing technology, thus deterministically controling the fast polishing time and efficiency.Key

Key words: manufacturingtechnologyandequipment, opticalelement, fastpolishing, materialremovalmodel

中图分类号:

TN205

林涛, 杨炜, 王健. 基于快速抛光技术的光学元件材料去除模型研究[J]. 兵工学报, 2017, 38(3): 527-533.

LIN Tao, YANG Wei, WANG Jian. Research on Material Removal Model of Optical Elements Based on Fast Polishing Technology[J]. Acta Armamentarii, 2017, 38(3): 527-533.

参考文献

［1］赵东峰, 邬融, 林尊琪, 等. 超声波辅助酸蚀提高熔石英损伤阈值[J]. 强激光与粒子束, 2015, 27(1):105-110.
ZHAO Dong-feng, WU Rong, LIN Zun-qi,et al.Acid etching combined with ultrasonic for improving laser damage threshold of fused silica[J]. High Power Laser and Particle Beams, 2015, 27(1): 105-110.(in Chinese)
[2］王洪祥, 朱本温, 陈贤华, 等. 抛光工艺参数对熔石英元件低频面形精度的影响[J]. 强激光与粒子束, 2015, 27(4):042001-1-042001-5.
WANG Hong-xiang, ZHU Ben-wen, CHEN Xian-hua, et al. Impact of polishing process parameters on the low frequency surface accuracy of fused silica optics[J]. High Power Laser and Particle Beams, 2015, 27(4):042001-1-042001-5.(in Chinese)
[3］ Mu Y, Zhuang Y, Sampurno Y,et al. Effect of pad groove width on slurry mean residence time and slurry utilization efficiency in CMP[J]. Microelectronic Engineering, 2016, 157:60-63.
[4］ Suratwala T I, Wong L L, Miller P E, et al. Sub-surface mechanical damage distribution during grinding of fused silica[J]. Journal of Non-Crystalline Solids, 2006, 352: 5601-5617.
[5］ Luo J F, Dornfeld D A. Material removal mechanism in chemical mechanical polishing: theory and modeling[J]. IEEE Transactions on Semiconductor Manufacturing, 2001, 14(2):112-133.
[6］ Runnels S R, Eyman L M. Tribology analysis of chemical mechanical polishing[J].Journal of Electrochemical Society, 1994, 141(6): 1698-1701.
[7］ Borst C L, Thakurta D G, Gill W N, et al. Surface kinetics model for SiLK chemical mechanical polishing[J]. Journal of Electrochemical Society, 2002, 149(2):118-127.
[8］ Zhao Y W,Chang L, Kim S H. A mathematical model for chemical mechanical polishing based on formation and removal of weakly bonded molecular species[J]. Wear, 2003, 254(3/4):332-339.
[9］ Zhao Y W,Chang L. A micro-contact and wear model for chemical-mechanical polishing of silicon wafers[J]. Wear, 2002, 252(3/4): 220-226.

[10］ Moon Y. Mechanical aspects of the material removal mechanism in chemical mechanism polishing (CMP)[D]. Berkeley: University of California at Berkeley, 1999.
[11］ Jiun Y L. Mechanics, mechanisms, and modeling of the chemical mechanical polishing process[D]. Massachusetts: Massachusetts Institute of Technology, 2001.
[12］ Yang W, Guo Y B, Li Y G, et al. Pressure and velocity dependence of the material removal rate in the fast polishing process[J]. Applied Optics, 2007, 47(33):6236-6242.
[13］ Marquez J J, Perez J M, Rios J, et al. Process modeling for robotic polishing[J]. Journal of Materials Processing Technology, 2005, 159(1):69-82.
[14］ Cook L M. Chemical processes in glass polishing[J]. Journal of Non-Crystalline Solids, 1990, 120(1/2/3):152-171.
[15］ Zhang F. Submicron particle adhension and removal in chemical-mechanical polishing and wafer cleaning process[D]. Potsdam: Clarksom University, 2002.
[16］ Greenwood J A, Williamson J B P. Contact of nominally flat surfaces[J]. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 1966, 295(1442): 300-319, 1996.

第38卷
第3期2017 年3月兵工学报ACTA
ARMAMENTARIIVol.38No.3Mar.2017

[1]	辛彬，李淑娟，李玉玺. 单晶硅电火花成形加工试验研究与工艺参数优化[J]. 兵工学报, 2017, 38(9): 1854-1861.
[2]	何泽地，田东宁，杨金川，姚智慧. 薄壁球壳真空吸附装夹变形力学分析与控制[J]. 兵工学报, 2017, 38(7): 1409-1415.
[3]	郑建新，刘威成，段玉涛. 7075铝合金二维超声挤压加工表面质量影响因素及其交互作用研究[J]. 兵工学报, 2017, 38(6): 1231-1238.
[4]	陈实现，刘双宇，张宏，李彦清，刘凤德. 激光-电弧复合焊等离子体特性与焊缝熔深相关性研究[J]. 兵工学报, 2017, 38(5): 978-985.
[5]	赵建社，周学德，周旭娇，汪文峰. 带冠整体叶轮电火花加工电极及其运动轨迹同步设计方法[J]. 兵工学报, 2017, 38(4): 744-749.
[6]	李强，谢里阳，李海洋，张芳敏，宋佳昕. 基于模糊综合层次评判法的精密齿轮制造工艺优化优先度分析[J]. 兵工学报, 2017, 38(4): 750-757.
[7]	杨臻，张平，蔡志海，秦航. 高强钢激光-电弧复合焊接接头力学性能研究[J]. 兵工学报, 2017, 38(3): 549-554.
[8]	陆益敏，黄国俊，郭延龙，丁方正，陈霞，韦尚方，米朝伟. 激光沉积大面积均匀类金刚石膜的设计改进及实验[J]. 兵工学报, 2017, 38(3): 555-560.
[9]	崔凤奎，凌远非，薛进学，李玉玺，李言，解克各. 花键冷滚打成形表层加工硬化研究[J]. 兵工学报, 2017, 38(2): 358-366.
[10]	张国华，李咚咚，李茂伟，张德远. 超声椭圆振动车削三维形貌形成研究[J]. 兵工学报, 2017, 38(10): 2002-2009.
[11]	李俊烨，卫丽丽，张心明，乔泽民. 介观尺度下磨粒流抛光温度对发动机喷油嘴质量影响研究[J]. 兵工学报, 2017, 38(10): 2010-2018.
[12]	张发平，吴迪，张体广，张凌雲，杨吉彬. 基于盲源信号分离的加工误差分离方法研究[J]. 兵工学报, 2016, 37(9): 1692-1699.
[13]	秦国华，孙烁，王华敏，左敦稳，吴铁军，鲁宇明. 基于工件稳定性的全区域夹紧力变向迭代规划算法[J]. 兵工学报, 2016, 37(9): 1700-1707.
[14]	巩亚东，孙瑶，刘寅. 低速单向走丝电火花线切割钛合金TC4表面粗糙度试验研究与建模[J]. 兵工学报, 2016, 37(6): 1058-1065.
[15]	孔令飞，牛晗，侯晓丽，林宏斌，王杰. 错齿内排屑刀具深孔加工中的刀具振动特性对孔圆度形貌的作用机制[J]. 兵工学报, 2016, 37(6): 1066-1074.

基于快速抛光技术的光学元件材料去除模型研究

Research on Material Removal Model of Optical Elements Based on Fast Polishing Technology

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价