超声局部共振系统设计与试验研究

doi:10.3969/j.issn.1000-1093.2019.08.026

摘要/Abstract

摘要： 超声振动加工能明显降低切削力及切削热、减小刀具磨损、提高加工效率，广泛应用于加工硬、脆等难加工材料。为避免刀具负载对谐振频率的影响，利用局部共振理论将振动系统分为变幅杆和工具杆两个子系统分别进行设计。由子系统连接处的输入总阻抗为0进而推导了复杂声学系统的频率方程，计算出振动系统尺寸。计算结果表明：模态分析及实际测量结果与理论偏差小于3%，满足设计要求，验证了局部共振理论设计的合理性；采用该方法设计的声学系统不受刀具本身负载影响，且在加工时力的波动较小，在一定程度上提高了系统稳定性，表明局部共振系统具有良好的加工效果。

关键词: 刀具, 超声局部共振, 振动系统, 频率方程, 阻抗综合法, 抗性负载, 力负载

Abstract: In ultrasonic vibration machining, the cutting force and cutting heat are significantly reduced, the tool wear is reduced, and the machining efficiency is improved. The ultrasonic vibration machining process is widely used for machining the difficult-to-machine materials, such as hard and brittle materials. In order to avoid the influence of tool load on the resonant frequency, the local resonance theory is used to divide the vibration system into two subsystems. The frequency equation of complex acoustic system is derived from the total input impedance equal to zero at the junction of the subsystems, and the size of vibration system is calculated. Calculated results show that the modal analysis results and the actual measured results are less than 3% deviation from the theoretical values, which meets the design requirements and verifies the correctness of the theoretical design of local resonance. The acoustic system designed by this method is not affected by the tool load, the fluctuation of force during processing is small, and the stability of the system is improved to some extent, indicating that the local resonance system has a good processing effect. Key

Key words: tool, ultrasoniclocalresonance, vibrationsystem, frequencyequation, compoundresistancemethod, resistanceload, forceload

中图分类号:

TG663

李鹏涛, 赵波，赵重阳，王毅. 超声局部共振系统设计与试验研究[J]. 兵工学报, 2019, 40(8): 1747-1755.

LI Pengtao， ZHAO Bo， ZHAO Chongyang， WANG Yi. Design and Experimental Study of Ultrasonic Local Resonance System[J]. Acta Armamentarii, 2019, 40(8): 1747-1755.

参考文献

［1］房善想, 赵慧玲, 张勤俭. 超声加工技术的应用现状及其发展趋势[J]. 机械工程学报, 2017, 53(19):22-32.
FANG S X, ZHAO H L, ZHANG Q J. The application status and development trends of ultrasonic machining technology[J]. Journal of Mechanical Engineering, 2017, 53(19):22-32.(in Chinese)
[2］ SHEN X H, XU G F. Study of milling force variation in ultrasonic vibration-assisted end milling[J]. Materials & Manufacturing Processes, 2017, 33(9): 644-650.
[3］ ZHAO B, JIA X F, CHEN F, et al. Control model and the experimental study on the ultrasonic vibration-assisted electrolytic in-process dressing internal grinding[J]. International Journal of Advanced Manufacturing Technology, 2017, 92(7/8):1-13.
[4］ ABBASI A, AMINI S, SHEIKHZADEH G A. Effect of ultrasonic peening technology on the thermal fatigue of rolling mill rolls[J]. International Journal of Advanced Manufacturing Technology, 2018,94(5/6/7/8):2499-2513.
[5］张园, 康仁科, 刘津廷, 等. 超声振动辅助钻削技术综述[J]. 机械工程学报,2017,53(19):33-34.
ZHANG Y,KANG R K, LIU J T, et al. Review of ultrasonic vibration assisted drilling[J]. Journal of Mechanical Engineering,2017,53(19):33-34.（in Chinese）
[6］别文博,赵波,王晓博,等.超声加工在齿轮抗疲劳制造中的研究综述与展望[J].表面技术,2018,47(7):35-51.
BIE W B, ZHAO B, WANG X B, et al. Overview and expectation on gear anti-fatigue manufacture by ultrasonic assisted machining[J]. Surface Technology,2018, 47(7): 35-51.(in Chinese)
[7］赵建, 王兵, 刘战强. 旋转超声滚压加工中的滚压力与滚压深度及表面形貌研究[J]. 兵工学报,2016,37(4):696-704.
ZHAO J,WANG B, LIU Z Q. The investigation into burnishing force, burnishing depth and surface morphology in rotary ultrasonic burnishing [J]. Acta Armamentarii, 2016, 37(4):696-704. (in Chinese)
[8］ LIAO Y S, CHEN Y C, LIN H M. Feasibility study of the ultrasonic vibration assisted drilling of Inconel superalloy[J]. International Journal of Machine Tools & Manufacture, 2007, 47(12/13):1988-1996.
[9］ BAGHLANI V, MEHBUDI P, AKBARI J, et al. An optimization technique on ultrasonic and cutting parameters for drilling and deep drilling of nickel-based high-strength Inconel 738LC superalloy with deeper and higher hole quality[J]. International Journal of Advanced Manufacturing Technology,2016, 82(5/6/7/8):1877- 1888.
[10］赵波, 陈凡, 贾晓凤, 等. 非谐振大工具头变幅杆优化设计及声学特性测试[J]. 陕西师范大学学报(自然科学版), 2017, 45(1):45-51.
ZHAO B, CHEN F, JIA X F, et al. Optimization design and characteristics test of non-resonant large tool head horn[J].Journal of Shaanxi Normal University (Natural Science Edition), 2017, 45(1):45-51.（in Chinese）
[11］付俊帆, 秦慧斌, 吕明. 基于Mindlin理论的功率超声纵弯谐振变幅器设计理论与实验研究[J]. 振动与冲击, 2018, 37(7): 259-266.
FU J F, QIN H B, L M. Design and experiment of ultrasonic longitudinal-flexural resonance transducer based on Mindlin theory[J]. Journal of Vibration and Shock, 2018, 37(7):259-266.（in Chinese）
[12］梁欣, 吕明, 秦慧斌,等. 纵向谐振变幅器的非谐振设计理论研究与验证[J]. 机械设计与制造, 2016 ,3(3):5-9.
LIANG X, L M, QIN H B, et al. Research and verification on the Nonnon-resonant design theory of longitudinal vibration transformer[J]. Machinery Design and Manufacture, 2016, 3(3): 5- 9.（in Chinese）
[13］范国良, 应崇福, 林忠茂, 等. 一种新型的超声加工深小孔的工具系统[J].应用声学, 1982 (1):2-7.
FAN G L, YING C F, LIN Z M, et al. A new tool system for deep small holes machined by ultrasonic machining [J]. Applied Acoustics, 1982(1): 2-7.（in Chinese）
[14］赵波, 何定东. 超声珩磨局部共振问题研究[J]. 现代制造工程, 1998,6(6):4-5.
ZHAO B, HE D D. Research on local resonance of ultrasonic honing[J]. Modern Manufacturing Engineering, 1998,6(6): 4-5.（in Chinese）
[15］徐可伟, 朱训生, 赵波. 用谐振来解释超声加工中的“局部共振”现象[J]. 应用声学, 2002, 21(5):30-33.
X K W, ZHU X S, ZHAO B. Using resonance to explain the phenomenon of “local resonance” in ultrasonic machining[J]. Applied Acoustics, 2002, 21(5): 30-33. （in Chinese）
[16］应崇福, 范国良. 超声复合振动系统中的“ 局部共振” 现象——20 年来的应用和机理分析情况[J].应用声学, 2002, 21(1):19-25.
YING C F, FAN G L. The phenomenon of“local resonance” in compound ultrasonic vibration systems—applications and mechanism analyses during the 20 years after its discovery [J]. Journal of Applied Acoustics, 2002, 21(1):19-25. （in Chinese）
[17］郑建新, 刘传绍, 高国富, 等. 超声振动钻削中局部共振现象的研究与应用[J]. 工具技术, 2003, 37(2):5-8.
ZHENG J X, LIU C S, GAO G F, et al. Research and application of local resonance phenomenon in ultrasonic vibration drilling[J]. Chinese Tool Engineering, 2003,37(2):5-8.（in Chinese）
[18］周光平, 鲍善惠, 程存弟，等. “局部共振”现象的理论解释[J]. 应用声学,1994, 13(6):39-42.
ZHOU G P, BAO S H, CHENG C D, et al. The theory explanation of the phenomenon of“local resonance” [J]. Applied Acoustics, 1994,13(6):39-42. （in Chinese）
[19］鲍善惠.超声耦合振动与“局部共振”现象[J].应用声学,1998, 17(4):6-10.
BAO S H. Ultrasonic coupled vibration and “local resonance” phenomenon [J]. Applied Acoustics, 1998, 17(4):6-10.（in Chinese）
[20］赵福令, 冯冬菊, 郭东明, 等. 超声变幅杆的四端网络法设计[J].声学学报,2002, 27(6): 554-558.
ZHAO F L, FENG D J, GUO D M, et al. Design of four terminal network method for ultrasonic horn[J]. Journal of Acoustics, 2002, 27(6):554-558.（in Chinese）
[21］张宁宁.指数型复合变幅杆的设计及负载特性研究[J].机械制造,2014,52(10):24-46.
ZHANG N N. Design and load characteristics of an exponential composite horn[J]. Machinery, 2014, 52(10):24-46.（in Chinese）

第40卷
第8期2019 年8月兵工学报ACTA
ARMAMENTARIIVol.40No.8Aug.2019

[1]	秦国华，高杰，叶海潮，姜国杰，黄帅，赖晓春. 基于融合评价指标和神经网络的刀具磨损预测[J]. 兵工学报, 2021, 42(9): 2013-2023.
[2]	李恒, 叶祖坤, 查文彬, 王禹林. 基于多传感器信息决策级融合的刀具磨损在线监测[J]. 兵工学报, 2021, 42(9): 2024-2031.
[3]	黄涛，刘志兵，王西彬，潘霖，闫正虎，冷寿阳. 刀轴侧倾角对薄壁叶片加工变形的影响[J]. 兵工学报, 2018, 39(3): 577-583.
[4]	李超，孔令飞, 梁炎眀, 江和龄, 晏冬. 基于刀具振动模式特征的深孔圆度误差预测方法[J]. 兵工学报, 2018, 39(2): 364-372.
[5]	王凯，孙剑飞，杜大喜，陈五一. 硬质合金刀具月牙洼磨损定量化实验研究[J]. 兵工学报, 2017, 38(8): 1578-1585.
[6]	孔令飞，牛晗，侯晓丽，林宏斌，王杰. 错齿内排屑刀具深孔加工中的刀具振动特性对孔圆度形貌的作用机制[J]. 兵工学报, 2016, 37(6): 1066-1074.
[7]	王新刚，吕春梅，赵玉倩，陈晓明. 基于刀具失效率的换刀策略研究[J]. 兵工学报, 2016, 37(5): 903-908.
[8]	姜振喜，孙杰, 李国超，贾兴民，李剑峰. TC4铣削加工的刀具磨损与切削力和振动关系研究[J]. 兵工学报, 2015, 36(1): 144-150.
[9]	王新刚，李鹤，吕春梅，王雪玲，逄旭. 硬质合金刀具的动态可靠性灵敏度研究[J]. 兵工学报, 2014, 35(1): 114-119.
[10]	秦国华, 张运建, 叶海潮. 基于神经网络的薄壁件加工变形预测方法[J]. 兵工学报, 2013, 34(7): 840-845.
[11]	高红俐,张立彬,姜伟,周寅. 电磁谐振式疲劳裂纹扩展试验固有频率跟踪系统[J]. 兵工学报, 2013, 34(7): 896-903.
[12]	孔令飞, 李言, 吕延军, 汤奥斐. 深孔加工刀具系统的动态稳定域研究[J]. 兵工学报, 2013, 34(5): 611-619.
[13]	于爱兵, 吴磊. 可再制造的电镀金刚石砂轮结构设计[J]. 兵工学报, 2013, 34(5): 620-626.
[14]	宋林森，邵贺，史国权. 高加速度值冲击振动系统在武器系统瞄准装置强度试验中的应用[J]. 兵工学报, 2013, 34(12): 1495-1499.
[15]	朱立达，于天彪，王宛山. 正交车铣加工切削力仿真分析[J]. 兵工学报, 2012, 33(4): 419-424.