HTPB/Al/AP/RDX固体推进剂动态混合过程数值仿真

胡木林; 武毅; 王行远; 郭松林; 于俊艺

doi:10.12382/bgxb.2024.0611

您当前的位置：

首页 >

文章列表页 >

HTPB/Al/AP/RDX固体推进剂动态混合过程数值仿真

更新时间：2025-09-05

- HTPB/Al/AP/RDX固体推进剂动态混合过程数值仿真
- Numerical Simulation of the Dynamic Mixing Process of HTPB/Al/AP/RDX Solid Propellant
- 兵工学报 2025年46卷第7期页码：240611
- 作者机构：
  
  1. 北京理工大学宇航学院, 北京 100081
  2. 北京理工大学重庆创新中心, 重庆 401100
- 作者简介：
  
  *yi.wu@bit.edu.cn
- 基金信息：
  
  国家自然科学基金项目(U2341288)
- DOI：10.12382/bgxb.2024.0611
  中图分类号：
- 收稿：2024-07-22，
  
  网络出版：2025-08-12，
  
  纸质出版：2025-07-31
- 稿件说明：
移动端阅览
胡木林, 武毅, 王行远, 等. HTPB/Al/AP/RDX固体推进剂动态混合过程数值仿真[J]. 兵工学报, 2025,46(7):240611.

Mulin HU, WUYi, Xingyuan WANG, et al. Numerical Simulation of the Dynamic Mixing Process of HTPB/Al/AP/RDX Solid Propellant[J]. Acta Armamentarii, 2025, 46(7): 240611.
胡木林, 武毅, 王行远, 等. HTPB/Al/AP/RDX固体推进剂动态混合过程数值仿真[J]. 兵工学报, 2025,46(7):240611. DOI： 10.12382/bgxb.2024.0611.

Mulin HU, WUYi, Xingyuan WANG, et al. Numerical Simulation of the Dynamic Mixing Process of HTPB/Al/AP/RDX Solid Propellant[J]. Acta Armamentarii, 2025, 46(7): 240611. DOI： 10.12382/bgxb.2024.0611.

摘要

混合工艺作为固体推进剂制备的重要工序

一般是指将Al、AP、RDX等颗粒相加入到高分子黏合剂基体中

经机械捏合、搅拌使黏合剂浆料涂敷在固体粒子表面的过程。基于Mixture固-气-液多相流模型

进行固体颗粒相加注混合釜中的扩散伴随桨叶动态捏合过程的数值仿真研究。开展不同固含量(0%~95%)药浆的动态流变测量实验

构建了药浆流变模型;考虑颗粒浓度动态变化对局部流变特性影响

开展了不同颗粒加注流量的混合动态过程仿真。分析不同工况条件下颗粒浓度、压力场和扭矩随时间的变化规律。实验结果表明:建立的数值仿真方法与文献实验结果对比

平均误差在15%内

具有良好的一致性;混合过程中近、远桨叶叶尖处的挤压力最大

而叶中部存在低压区;混合过程中

桨叶扭矩呈锯齿状波动变化

随着颗粒相的加注

扭矩逐渐增大;固体颗粒相加注流量小幅增大时

扭矩变化较小;加注流量大幅增大时

扭矩增幅可达90%。连续加料混合过程中远心桨的扭矩值持续上升

最终平均值可达初始阶段的19倍。所得成果可为固体推进剂的混合工艺效率提升和安全性研究提供参考。

Abstract

The mixing process

as a crucial step in the fabrication of solid propellants

typically involves the incorporation of particulate phases such as aluminum (Al)

ammonium perchlorate (AP)

and RDX into a polymeric binder matrix.The binder slurry is applied onto the solid particles through mechanical kneading and stirring.The dispersion accompanied by dynamic blade kneading during the co-mingling of solid particulate phases in a mixer is simulated based on the Mixture solid-gas-liquid multiphase flow model.Dynamic rheological measurements of slurries with varying solid contents (0%-95%) are performed to construct a rheological model of propellant slurry.Considering the dynamic changes in granular concentration and their impact on local rheological properties

the mixing dynamic processes at different granular injection flow rates are simulated.The analysis focuses on the temporal patterns of granular concentration

pressure fields

and torque under various operating conditions.The results indicate that the proposed numerical simulation method is in good agreement with experimental results in Ref.[39] with an average error of less than 15%.The study reveals that the greatest pressure occurs at the tips of the near and far blades

while a low-pressure zone exists in the middle of the blades.During mixing

the blade torque exhibits a serrated fluctuation

and gradually increases with the addition of the particulate phase.A slight increase in the granular injection flow rate results in a minimal torque change.However

a significant increase in flow rate could lead to a torque increase of up to 90%.In the continuous feeding mixing process

the torque value at the farthest blade from the axis of rotation continues to rise

eventually reaching an average value 19 times that at the initial stage.This research provides insights for enhancing the efficiency and safety studies of solid propellant mixing processes.

关键词

Keywords

references

李莹新 , 莫纪安 , 王秀云 , 等 . 固体火箭发动机壳体复合材料研究进展 [J ] . 航天制造技术 , 2020 ( 4 ): 65 - 69 .

LI Y X , MO J A , WANG X Y , et al. Research progress on composite materials for solid rocket motor casing [J ] . Aerospace Manufacturing Technology , 2020 ( 4 ): 65 - 69 . (in Chinese)

JAIN M , SINGH D , MEHILAL , et al. Studies on rheological behavior of composite propellant slurry on sequential incorporation of ingredients to predict qualitative mixing pattern [J ] . Advanced Science,Engineering and Medicine , 2015 , 7 ( 10 ): 849 - 854 .

时茗扬 , 李春娜 , 刘洋 , 等 . 不确定性下的固体火箭发动机性能精确代理建模方法 [J ] . 推进技术 , 2025 , 46 ( 1 ): 32 - 41 .

SHI M Y , LI C N , LIU Y , et al. Precise surrogate modeling method for solid rocket motor performance under uncertainty [J ] . Journal of Propulsion Technology , 2025 , 46 ( 1 ): 32 - 41 . (in Chinese)

朱艳明 , 吕端 , 胡润芝 , 等 . 固体推进剂连续混合工艺参数控制与工程优化 [J ] . 固体火箭技术 , 2020 , 43 ( 6 ): 776 - 781 .

ZHU Y M , LÜ D , HU R Z , et al. Control and engineering optimization of continuous mixing process parameters for solid propellants [J ] . Journal of Solid Rocket Technology , 2020 , 43 ( 6 ): 776 - 781 . (in Chinese)

ASHIGAKI K , IWASAKI A , HAGIWARA D , et al. Considering mixing process of rocket solid propellant using mixing transport device simulating peristaltic movement of intestinal tract[C ] //Proceedings of the 2018 7th IEEE International Conference on Biomedical Robotics and Biomechatronics ( Biorob).Enschede,Netherlands:IEEE ,2018: 1291 - 1296 .

武宇恒 , 蔚红建 , 付小龙 . 固体推进剂的流变性能及工艺仿真研究进展 [J ] . 火工品 , 2024 ( 2 ): 58 - 64 .

WU Y H , WEI H J , FU X L . Research progress on the rheological properties and process simulation of solid propellants [J ] . Initiators and Pyrotechnics , 2024 ( 2 ): 58 - 64 . (in Chinese)

ABDILLAH L H , WINARDI S , SUMARNO S , et al. Effect of mixing time to homogeneity of propellant slurry [J ] . IPTEK Journal of Proceedings Series , 2018 ( 1 ): 94 - 98 .

GALLANT F M , PRICKETT S E , CESAREC M , et al. Ingredient and processing effects on the burning rates of composite rocket propellants utilizing a reduced-run mixture-process experiment design [J ] . Chemometrics & Intelligent Laboratory Systems , 2008 , 90 ( 1 ): 49 - 63 .

ZHAO R , HUANG J , ZHUANG Z , et al. Numerical simulation of propellant slurry stirring process [J ] . Journal of Physics:Conference Series . IOP Publishing , 2022 , 2252:012029 .

关英波 . 立式捏合机搅拌桨叶的力学数值分析 [D ] . 武汉 : 华中科技大学 , 2007 .

GUAN Y B . Numerical analysis of the mechanics of stirring blades in a vertical kneader [D ] . Wuhan : Huazhong University of Science and Technology , 2007 . (in Chinese)

景玲 . 立式捏合机搅拌桨叶应力与温度数值分析研究 [D ] . 西安 : 西安工业大学 , 2013 .

JING L . Research on numerical analysis of stress and temperature of stirring blades in a vertical kneader [D ] . Xi’an : Xi’an Technological University , 2013 . (in Chinese)

徐江华 . 立式捏合机搅拌桨叶的转矩数值分析 [D ] . 武汉 : 华中科技大学 , 2012 .

XU J H . numerical analysis of torque of stirring blades in a vertical kneader [D ] . Wuhan : Huazhong University of Science and Technology , 2012 . (in Chinese)

LONG J C , HE Y , ZHAN X B , et al. Study of kneading pressure and power consumption in a twin-blade planetary mixer for mixing highly viscous fluids [J ] . Chemical Engineering Science , 2021 ,241:116723.

CHENG W K , YE Y , JIANG S X , et al. Mixing intensification in a horizontal self-cleaning twin-shaft kneader with a highly viscous Newtonian fluid [J ] . Chemical Engineering Science , 2019 ,201: 437 - 447 .

易朋兴 , 胡友民 , 崔峰 , 等 . 立式捏合机捏合间隙影响CFD分析 [J ] . 化工学报 , 2007 , 58 ( 10 ): 2680 - 2684 .

YI P X , HU Y M , CUI F , et al. The influence of intercalation gap on CFD analysis in vertical kneaders [J ] . CIESC Journal , 2007 , 58 ( 10 ): 2680 - 2684 . (in Chinese)

吴玉金 , 野延年 . 混合生产中固体推进剂的安全问题 [J ] . 固体火箭技术 , 1998 ( 4 ): 53 - 55 .

WU Y J , YE Y N . Safety issues of solid propellants in mixing production [J ] . Journal of Solid Rocket Technology , 1998 ( 4 ): 53 - 55 . (in Chinese)

李胜婷 , 庞维强 , 南风强 , 等 . 不同因素对固体推进剂流变性能影响研究进展 [J ] . 火炸药学报 , 2024 , 47 ( 2 ): 114 - 130 .

LI S T , PANG W Q , NAN F Q , et al. Research progress on the influence of different factors on the rheological properties of solid propellants [J ] . Chinese Journal of Explosives & Propellants , 2024 , 47 ( 2 ): 114 - 130 . (in Chinese)

李胜婷 , 庞维强 , 南风强 , 等 . 复合固体推进剂药浆浇铸工艺仿真及优化 [J ] . 火炸药学报 , 2024 , 47 ( 10 ): 937 - 944 .

LI S T , PANG W Q , NAN F Q , et al. Simulation and optimization of casting process for composite solid propellant slurry [J ] . Chinese Journal of Explosives & Propellants , 2024 , 47 ( 10 ): 937 - 944 . (in Chinese)

朱宏春 , 王吉强 , 苗建波 . NEPE推进剂药浆固化初期特殊流变性能研究 [J ] . 推进技术 , 2013 , 34 ( 10 ): 1420 - 1425 .

ZHU H C , WANG J Q , MIAO J B . Study on the special rheological properties of NEPE propellant slurry in the early stage of cure [J ] . Journal of Propulsion Technology , 2013 , 34 ( 10 ): 1420 - 1425 . (in Chinese)

杜幸 , 刘晋湘 , 陈江波 , 等 . 丁羟推进剂流变性研究 [J/OL ] . 火炸药学报 , 2025 [ 2025-07-10 ] .https://doi.org/ 10.14077/j.issn.1007-7812.202303035. https://dx.doi.org/10.14077/j.issn.1007-7812.202303035.

DU X , LIU J X , CHEN J B , et al. Study on the rheology of butanetriol (BTT) based propellants [J/OL ] . Chinese Journal of Explosives & Propellants , 2025 [ 2025-07-10 ] .https://doi.org/ 10.14077/j.issn.1007-7812.202303035. https://dx.doi.org/10.14077/j.issn.1007-7812.202303035. (in Chinese)

江晓瑞 , 李卓 , 鲁荣 , 等 . 丁羟推进剂药浆固化过程中触变性转变规律研究 [J ] . 推进技术 , 2020 , 41 ( 5 ): 1178 - 1184 .

JIANG X R , LI Z , LU R , et al. Study on the thixotropic transition law of butanetriol (BTT) based propellant slurry during the cure process [J ] . Journal of Propulsion Technology , 2020 , 41 ( 5 ): 1178 - 1184 . (in Chinese)

潘新洲 , 李尚文 , 姜磊 , 等 . 少铝HTPE推进剂药浆流变特性研究 [J ] . 固体火箭技术 , 2021 , 44 ( 5 ): 656 - 661 .

PAN X Z , LI S W , JIANG L , et al. Study on the rheological properties of low-aluminum HTPE propellant slurry [J ] . Journal of Solid Rocket Technology , 2021 , 44 ( 5 ): 656 - 661 . (in Chinese)

江晓瑞 , 李卓 , 韩秀洁 , 等 . 固体推进剂药浆改进Herschel-Bukely模型及其在仿真分析中的应用 [J ] . 推进技术 , 2019 , 40 ( 9 ): 2137 - 2143 .

JIANG X R , LI Z , HAN X J , et al. Improved Herschel-Buckley model for solid propellant slurry and its application in simulation analysis [J ] . Journal of Propulsion Technology , 2019 , 40 ( 9 ): 2137 - 2143 . (in Chinese)

LIU B , XIAO L , WU Z K , et al. Evaluation of blend uniformity and terminal point during continuous mixing in water for modified Double-Base propellant components using a Near-Infrared method [J ] . ACS Omega , 2022 , 7 ( 20 ): 17098 - 17107 . DOI: 10.1021/acsomega.2c00532 http://doi.org/10.1021/acsomega.2c00532 A near-infrared (NIR) spectrometer was used to test the double-base absorbent powder sample and to quantitatively analyze the contents of each component as well as their dispersion uniformity to establish a rapid quantitative test method for blending uniformity of modified double-base (MDB) propellant components. First, the quantitative calibration models of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) were constructed based on sample testing, and the RDX model's correlation coefficient was 0.9929. Then, during the blending process, NIR spectra were continually collected. For the original spectra of samples, the blend uniformity was assessed using the coefficient of moving block standard deviation (MBSD). After 160 min, the sample's MBSD value had reached a steady state of less than 0.003, indicating that the sample's components were distributed uniformly. The findings reveal that NIR spectroscopy can be used to verify the blending uniformity of MDB propellant components.© 2022 The Authors. Published by American Chemical Society.

梁建 , 朱剑波 , 段丽华 , 等 . 立式捏合机桨叶结构与桨叶变形量的CFD仿真 [J ] . 固体火箭技术 , 2018 , 41 ( 6 ): 745 - 749 ,753.

LIANG J , ZHU J B , DUAN L H , et al. CFD Simulation of blade structure and blade deformation of vertical kneader [J ] . Journal of Solid Rocket Technology , 2018 , 41 ( 6 ): 745 - 749 ,753. (in Chinese)

杨明金 . 立式捏合机混合釜内固体推进剂药浆混合的研究 [D ] . 武汉 : 华中科技大学 , 2008 .

YANG M J . Research on the mixing of solid propellant slurry in the mixing pot of vertical kneader [D ] . Wuhan : Huazhong University of Science and Technology , 2008 . (in Chinese)

洪寅 , 刘看 , 武毅 , 等 . 固体推进剂药浆立式混合过程SPH方法研究 [J ] . 含能材料 , 2024 , 32 ( 11 ): 1162 - 1173 .

HONG Y , LIU K , WU Y , et al. Study on the SPH method of solid propellant slurry vertical mixing process [J ] . Chinese Journal of Energetic Materials , 2024 , 32 ( 11 ): 1162 - 1173 . (in Chinese)

王建 , 刘皓 , 赵亚风 , 等 . 复合固体推进剂双螺杆挤出成型过程DEM-CFD耦合仿真 [J ] . 含能材料 , 2022 , 30 ( 2 ): 138 - 145 .

WANG J , LIU H , ZHAO Y F , et al. Coupled simulation of DEM-CFD in the extrusion molding process of composite solid propellants [J ] . Chinese Journal of Energetic Materials , 2022 , 30 ( 2 ): 138 - 145 . (in Chinese)

LU T T , LI K , LIU F Q , et al. Numerical simulation of solid-liquid suspension in a slurry electrolysis stirred tank [J ] . Chemical Engineering Research & Design:Transactions of the Institution of Chemical Engineers , 2023 ,189: 371 - 383 .

LI B , WANG J T . Mixing intensification through modifications of PBT impellers studied by DEM-VOF method [J ] . Chemical Engineering and Processing-Process Intensification , 2022 ,177:109001.

HAVLICA J , KOZAKOVIC D , et al. The effect of primary and secondary flows on the homogenization process in a vertical bladed mixer [J ] . Powder Technology , 2021 ,391: 253 - 266 .

SINNOTT M D , HARRISON S M , CLEARY P W . A particle-based modelling approach to food processing operations [J ] . Food and Bioproducts Processing , 2021 ,127: 14 - 57 .

敖维坚 , 张立新 , 苏昌银 , 等 . 复合推进剂装药混合中的扭矩安全值 [J ] . 固体火箭技术 , 2020 , 43 ( 1 ): 53 - 58 .

AO W J , ZHANG L X , SU C Y , et al. Torque safety value in the mixing of composite propellants [J ] . Journal of Solid Rocket Technology , 2020 , 43 ( 1 ): 53 - 58 . (in Chinese)

张力恒 , 苏昌银 , 何煜 , 等 . 推进剂装药混合过程安全性研究 [J ] . 固体火箭技术 , 2012 , 35 ( 4 ): 508 - 512 .

ZHANG L H , SU C Y , HE Y , et al. Research on the safety of propellant mixing process [J ] . Journal of Solid Rocket Technology , 2012 , 35 ( 4 ): 508 - 512 . (in Chinese)

MIKKO M , VEIKKO T , SIRPA K . On the mixture model for multiphase flow [J ] . VTT Publications , 1996 ,288: 3 - 67 .

LU H L , GIDASPOW D . Hydrodynamics of binary fluidization in a riser:CFD simulation using two granular temperatures [J ] . Chemical Engineering Science , 2003 , 58 ( 16 ): 3777 - 3792 .

ZHANG J Q , LI X W , HE R B , et al. Study on double-shaft mixing paddle undergoing planetary motion in the laminar flow mixing system [J ] . Advances in Mechanical Engineering , 2015 , 7 ( 7 ): 1687814015592603 .

王正方 , 翟瑞清 . 立式捏合机搅拌桨的设计 [J ] . 固体火箭技术 , 1993 ( 1 ): 65 - 69 .

WANG Z F , ZHAI R Q . Design of stirring blades for vertical kneader [J ] . Journal of Solid Rocket Technology , 1993 ( 1 ): 65 - 69 . (in Chinese)

YOUCEFI A , ANNE-ARCHARD D , BOISSON H C , et al. On the Influence of liquid elasticity on mixing in a vessel agitated by a Two-Bladed impeller [J ] . Journal of Fluids Engineering , 1997 , 119 ( 3 ): 616 - 622 .

DELAPLACE G , THAKUR R K , BOUVIER L , et al. Dimensional analysis for planetary mixer:Mixing time and Reynolds numbers [J ] . Chemical Engineering Science , 2007 , 62 ( 5 ): 1442 - 1447 .

浏览量

376

下载量

CNKI被引量

文章被引用时，请邮件提醒。

提交

工具集

关联资源

暂无数据