浏览全部资源
扫码关注微信
Accurate Internal Ballistics Modeling and Testing of Rodless High Pressure Pneumatic Catapult Considering Leakage
- Acta Armamentarii Vol. 44, Issue 7, Pages: 1867-1880(2023)
- 作者机构：
1. 南京理工大学 机械工程学院, 江苏 南京 210094
2. 陆军研究院 工程设计研究所, 江苏 南京 210016
- 作者简介：
- 基金信息：
DOI：10.12382/bgxb.2022.0172
CLC：Received：18 March 2022，
Published Online：07 August 2023，
Published：30 July 2023
- 稿件说明：
移动端阅览
Xueqin WANG, Wuning MA, Dawei MA, et al. Accurate Internal Ballistics Modeling and Testing of Rodless High Pressure Pneumatic Catapult Considering Leakage[J]. Acta Armamentarii, 2023, 44(7): 1867-1880.
Xueqin WANG, Wuning MA, Dawei MA, et al. Accurate Internal Ballistics Modeling and Testing of Rodless High Pressure Pneumatic Catapult Considering Leakage[J]. Acta Armamentarii, 2023, 44(7): 1867-1880. DOI： 10.12382/bgxb.2022.0172.
摘要
无杆式高压气动弹射器因开口的固有结构决定其存在一定量的泄漏
为此设计并开展样机泄漏测试试验。基于由实验数据拟合的标准干空气热力学状态方程
分别按理想气体和真实气体对比计算泄漏率
并拟合泄漏率随压力、行程变化的经验公式。建立考虑动态泄漏、真实气体效应及真实开阀规律的精确内弹道模型
对考虑和不考虑泄漏两种工况的结果进行对比
并详细分析考虑泄漏的弹射过程中热力学参数与负载运动参数的变化规律
将其与弹射试验数据、流体仿真结果进行对比。研究结果表明:按理想气体计算的泄漏率比真实气体偏小约4%;泄漏率不超过4%/s;考虑泄漏的精确内弹道模型计算结果与弹射试验数据、流体仿真结果均基本一致
具有较高的计算精度。
Abstract
The rodless high-pressure pneumatic catapult experiences a certain amount of leakage due to the inherent structure of the opening. In this study
a prototype leakage test is designed and conducted. Based on the standard dry air thermodynamic equation of state fitted by the experimental data
the leakage rate is calculated and compared under the hypothesis of ideal gas and real gas. The empirical formula of leakage rate varying with pressure and stroke is fitted. An accurate interior ballistic model considering dynamic leakage
real gas effects
and the real valve opening law is established. The two working conditions with and without leakage are solved numerically and compared. Then
the variation laws of thermodynamic parameters and load motion parameters in the ejection process with leakage are analyzed in detail and compared with the ejection test data and fluid simulation results. The results show that the leakage rate calculated under ideal gas assumption is about 4% lower than that under real gas assumption. Moreover
the calculated leakage rate shall not exceed 4%/s. The calculation results of the accurate interior ballistic model considering leakage are basically consistent with the ejection test data and the fluid simulation results
indicating high calculation accuracy.
关键词
Keywords
references
谭大成 . 弹射内弹道学 [M ] . 北京 : 北京理工大学出社 , 2015 .
TAN D C . Interior ballistics of catapults [M ] . Beijing : Beijing Institute of Technology Press , 2015 . (in Chinese)
芮守祯 , 邢玉明 . 几种导弹弹射动力系统内弹道性能比较 [J ] . 北京航空航天大学学报 , 2009 , 5 ( 6 ): 766 - 770 .
RUI S Z , XING Y M . Comparative studies of interior-ballistic performance among several missile eject power systems [J ] . Journal of Beijing Aerospace University , 2009 , 5 ( 6 ): 766 - 770 . (in Chinese)
姚琳 , 马大为 , 任杰 , 等 . 无杆式气缸弹射装置内弹道仿真与优化设计 [J ] . 振动与冲击 , 2017 , 36 ( 6 ): 122 - 127 .
YAO L , MA D W , REN J , et al . Internal ballistics simulatinon and improving of rodless cylinder cold launching device [J ] . Vibration and Shock , 2017 , 36 ( 6 ): 122 - 127 . (in Chinese)
杨风波 , 马大为 , 杨帆 , 等 . 高压弹射装置内弹道建模与计算 [J ] . 兵工学报 , 2013 , 4 ( 5 ): 527 - 534 .
YANG F B , MA D W , YANG F , et al . Interior ballistics modeling and calculation of high-pressure ejection device [J ] . Acta Armamentarii , 2013 , 4 ( 5 ): 527 - 534 . (in Chinese)
SOAVE G . Equilibrium constants from a modified redlieh-kwong equation of state [J ] . Chemical Engineering Science , 1972 , 27 : 1197 - 1203 . DOI: 10.1016/0009-2509(72)80096-4 http://doi.org/10.1016/0009-2509(72)80096-4 https://linkinghub.elsevier.com/retrieve/pii/0009250972800964 https://linkinghub.elsevier.com/retrieve/pii/0009250972800964
PENG D Y , ROBINSON D . A new two-constant equation of state [J ] . Industrial & Engineering Chemistry Fundamentals , 1976 , 15(l) : 59 - 64 .
LEMMON E W , JACOBSEN R T , PENONCELLO S G , et al . Thermodynamic properties of air and mixtures of nitrogen 2000 K at pressure to 2000MPa [J ] . Journal Chemical Reference , 2000 , 29 ( 3 ): 331 - 385 .
李悦 , 裴锦华 . 无人机气液压发射动力学数值仿真 [J ] . 机械工程学报 , 2011 , 47 ( 8 ): 183 - 190 . 气液压发射起飞是近年来国际上出现的一种先进的中小型无人机发射方式，以气液压能源提供动力实现无人机发射起飞。基于气液压系统原理，对蓄能器气体弹簧的弹性系数进行分析，建立由气液压系统动力学模型、增速滑轮组动力学模型、无人机及滑车的运动方程构成的发射过程动力学模型，并进行仿真计算和数值分析，分析结果表明无人机及滑车质量、蓄能器充油压力、液压缸活塞有效面积、蓄能器容积是影响发射过程和起飞速度的关键参数，在一定范围内通过调节气液压系统参数可适应于不同的无人机起飞质量和起飞速度要求。采用与试验结果比对的方法修正气液压系统的总粘性阻尼系数，将仿真结果与试验结果进行对比研究，研究结果表明仿真计算结果与试验结果表现出较好的一致性，证明了发射过程动力学模型的正确性，为无人机气液压发射装置的工程研制提供了重要的理论参考。
LI Y , PEI J H . Dynamic Numerical simulation of the pneumatic and hydraulic launching of UAV [J ] . Journal of Mechanical Engineering , 2011 , 47 ( 8 ): 183 - 190 . (in Chinese) The takeoff by pneumatic and hydraulic launching is an international advanced launching technology of medium and small unmanned aerial vehicles (UAV) recently. The power for launching comes from pneumatic and hydraulic energy. The elastic coefficient of accumulator gas spring is analyzed on the basis of the principle of pneumatic and hydraulic systems. The dynamic models of launching process are built and simulated, including dynamics models of pneumatic and hydraulic systems and pulley block system and movement equations of UAV and shuttle. The results of simulative calculation and numerical analysis indicate that the mass of UAV and the shuttle, the accumulator volume and oil charge pressure and the effective area of hydraulic cylinder piston are the key parameters affecting launch process and takeoff velocity. Moreover, adjusting the parameters of pneumatic and hydraulic systems within a certain range can adapt to different requirements of takeoff mass and velocity of UAV. The total viscosity damp coefficient of pneumatic and hydraulic systems is corrected by comparing with the experiment result. The result of simulation is in good accordance with that of experiment, which proves the correctness of the dynamic models of launching process, thus providing an important theoretical reference for the development of pneumatic and hydraulic launching equipment of UAV.
田兵 , 王树宗 , 练永庆 . 水下蓄能式发射装置结构优化 [J ] . 兵工学报 , 2011 , 32 ( 9 ): 1094 - 1098 . 为研究新型水下蓄能式鱼雷发射装置，建立了水下蓄能式发射装置发射过程数学模型。运用遗传算法对水下蓄能式发射装置结构参数和内弹道参数进行了优化计算，在优化过程中，针对参数多、单位及数值数量级不同的情况，采用参数归一化处理成无量纲值，把多目标优化问题转化为单目标优化问题，并采用罚函数法处理约束条件。优化结果表明：优化后的结构参数不但满足发射要求，而且装置的体积小、质量轻、内弹道性能更好。
TIAN B , WANG S Z , LIAN Y Q . Structure optimization for underwater energy-accumulated launcher [J ] . Acta Armamentarii , 2011 , 32 ( 9 ): 1094 - 1098 . (in Chinese) To study new type of underwater energy-accumulated torpedo launcher, its mathematical mode is built. Its structure and interior ballistic parameters are optimized by using genetic algorithm. For several parameters and their different units and magnitudes, normalization is applied to transfer multi-objective optimization to single-object optimization, and penalty function method is used to deal with restriction condition. The optimization results show that the optimized structure parameters meet the requirements of launching well and the launcher has small volume, light weight and better interior ballistic performance.
赫雷 , 尚兴超 , 周克栋 , 等 . 一种压缩空气驱动的武器发射过程动力学分析 [J ] . 振动与冲击 , 2014 , 33 ( 21 ): 202 - 206 .
HE L , SHANG X C , ZHOU K D , et al . Dynamic analyis for launching process of a compressed air-driving weapon [J ] . Vibration and Shock , 2014 , 33 ( 21 ): 202 - 206 . (in Chinese)
卢伟 , 马晓平 , 周明 . 无人机气动弹射动力学仿真与优化 [J ] . 西北工业大学学报 , 2014 , 32 ( 6 ): 865 - 871 .
LU W , MA X P , ZHOU M . Dynamic simulation and optimization of UAV pneumatic launching [J ] . Journal of Northwestern Polytechnical University , 2014 , 32 ( 6 ): 865 - 871 . (in Chinese)
刘少刚 , 刘刚 , 赵丹 , 等 . 气动发射灭火炮伴随式击发装置研究 [J ] . 兵工学报 , 2013 , 34 ( 10 ): 1318 - 1323 . DOI: 10. 3969/ j. issn. 1000-1093. 2013. 10. 019 http://doi.org/10. 3969/ j. issn. 1000-1093. 2013. 10. 019 研究了一种可以快速加压的气动灭火炮击发装置。采用伴随管随动发射,解决了高压气体发射击发时膛内发射气压需要瞬态达到气室压力的难题。建立了击发过程动力学模型和膛内 气体参数模型,给出了击发过程灭火弹运动方程。通过对击发过程进行仿真分析,得到了击发过程 膛内气体参数变化特性。研究了不同击发角对击发特性的影响,得到了最优击发角。通过MATLAB 软件对击发装置的撞击过程进行了校核。研究结果表明,伴随管式击发装置能有效地解决膛 内发射气压瞬态达到气室压力的要求。
LIU S G , LIU G , ZHAO D , et al . Research on the associated-tube type firing mechanism for pneumatic Fire-extinguishing cannon [J ] . Acta Armamentarii , 2013 , 34 ( 10 ): 1318 - 1323 . (in Chinese)
牛清勇 , 李天匀 , 朱翔 , 等 . 水下气动发射装置发射性能参数灵敏度分析 [J ] . 哈尔滨工程大学学报 , 2015 , 36 ( 7 ): 877 - 881 .
NIU Q Y , LI T Y , ZHU X , et al . Sensitivity analysis of the performance parameters of an underwater pneumatic launcher [J ] . Journal of Harbin Engineering University , 2015 , 36 ( 7 ): 877 - 881 . (in Chinese)
李博平 , 李国庆 , 张笈玮 , 等 . 压缩空气弹射系统内弹道特性 [J ] . 兵工学报 , 2021 , 42 ( 12 ): 2606 - 2616 . DOI: 10.3969/j.issn.1000-1093.2021.12.008 http://doi.org/10.3969/j.issn.1000-1093.2021.12.008 为分析压缩空气弹射系统内弹道特性，以压缩空气弹射装置为研究对象建立弹射过程内弹道数学模型。通过数值计算，分析发射阀全开时间、发射阀最大流通面积和低压室初始容积对内弹道特性的影响规律。结果表明：发射阀全开时间越短，弹射总时间越短，弹体出筒初始速度越高，弹体过载也越大；在一定范围内，随着发射阀最大流通面积增大，弹射总时间变短，弹体初速度增高，弹体过载变化越平缓，但发射阀最大流通面积对弹体最大过载影响较弱；低压室初始容积对弹射行程和弹体出筒初始速度影响较弱，对弹射初期弹体过载影响较大。
LI B P , LI G Q , ZHANG J W , et al . Ballistics of submarine ballistic missile launch system [J ] . Acta Armamentarii , 2021 , 42 ( 12 ): 2606 - 2616 . (in Chinese)
REN J , YANG F B , MA D W , et al . Pneumatic performance study of a high pressure ejection device based on real specific energy and specific enthalpy [J ] . Energy , 2014 , 16 ( 9 ): 4801 - 4817 .
杨风波 , 马大为 , 杨帆 , 等 . 高压弹射装置内弹道建模与计算 [J ] . 兵工学报 , 2013 , 4 ( 5 ): 527 - 534 .
YANG F B , MA D W , YANG F , et al . Interior ballistics modeling and calculation of high-pressure ejection device [J ] . Acta Armamentarii , 2013 , 4 ( 5 ): 527 - 534 . (in Chinese)
YANG F B , MA D W , LE G G . Real thermodynamic energy and enthalpy on high pressure pneumatic system based on improved virial equation [J ] . Advanced Materials Research , 2013 , 694 : 734 - 738 .
任锐 , 马大为 , 姚琳 , 等 . 多级气动液压弹射装置建模及性能研究 [J ] . 兵工学报 , 2016 , 7 ( 8 ): 1365 - 1372 .
REN R , MA D W , YAO L , et al . Theoretical modeling and performance research on multi-stage pneumatic and hydraulic catapult device [J ] . Acta Armamentarii , 2016 , 7 ( 8 ): 1365 - 1372 . (in Chinese)
GU S W , LI Y X , Teng L . An experimental study on the flow characteristics during the leakage of high pressure CO 2 pipelines [J ] . Process Safety and Environmental Protection , 2019 , 125 : 92 - 101 . DOI: 10.1016/j.psep.2019.03.010 http://doi.org/10.1016/j.psep.2019.03.010 https://linkinghub.elsevier.com/retrieve/pii/S0957582018311170 https://linkinghub.elsevier.com/retrieve/pii/S0957582018311170
TU R , XIE Q Y , YI J X , et al . An experimental study on the leakage process of high pressure CO 2 from a pipeline transport system [J ] . Greenhouse Gases: Science and Technology , 2014 ( 4 ): 777 - 784 .
姚琳 , 马大为 , 任杰 , 等 . 高速无杆气缸作动器密封圈润滑性能分析 [J ] . 浙江大学学报(工学版) , 2017 , 51 ( 8 ): 1568 - 1574 .
YAO L , MA D W , REN J , et al . Lubrication performance analysis of high-speed rod-less cylinder seal [J ] . Journal of Zhejiang University (Engineering Science) , 2017 , 51 ( 8 ): 1568 - 1574 . (in Chinese)
0
Views
605
下载量
0
CNKI被引量
- L-PDFDownload
- Meta-XMLDownload
- BibTeXDownload
- EndnoteDownload
- RefMan Download
- NoteExpressDownload
- NoteFirstDownload
Publicity Resources
Related Articles
Related Author
Related Institution
- Postal code：100089
- Tel：010-68963060/68962718 Fax：010-68963025 Email：bgxb@cos.org.cn
- Technical support is provided by Beijing Founder electronics co., LTD 京ICP备05059581号-4
京公网安备11010802024360号 - It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
- Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.
- Total Visits：44495 Visits Today：475