
浏览全部资源
扫码关注微信
1. 北京理工大学 机械与车辆学院, 北京 100081
2. 中国北方车辆研究所 底盘部件技术部, 北京 100072
3. 陆军装甲兵学院 车辆工程系, 北京 100072
4. 重庆大学 机械传动国家重点实验室, 重庆 400044
Received:31 August 2021,
Published Online:10 March 2023,
Published:28 February 2023
移动端阅览
Huixin SONG, Liang GU, Jinqiu ZHANG, et al. Inertia Analysis and Vibration Filtering Buffer Design of Electromechanical Suspension of High Speed Tracked Vehicle[J]. Acta Armamentarii, 2023, 44(2): 380-393.
Huixin SONG, Liang GU, Jinqiu ZHANG, et al. Inertia Analysis and Vibration Filtering Buffer Design of Electromechanical Suspension of High Speed Tracked Vehicle[J]. Acta Armamentarii, 2023, 44(2): 380-393. DOI: 10.12382/bgxb.2021.0588.
为解决高速履带车辆机电悬架在高频区性能恶化与结构可靠性的问题
分析基于扭杆的机电悬架刚度特性
求解悬架杆系复杂运动关系
计算机电执行器的等效惯性质量
建立考虑惯性质量与负重轮阻尼的2自由度机电悬架模型。量化分析惯性质量对悬架性能的不利影响
得到影响悬架平顺性、部件可靠性的惯性力的频域分布区间与功率谱密度分布区间。根据悬架惯性力的频域分布
以及悬架动挠度的幅频特性
提出滤振与缓冲的措施
建立带有滤振缓冲器的悬架模型。仿真和试验结果表明:滤振缓冲能够有效降低惯性质量影响
在D级路面40km/h行驶工况下
将原惯性力的均方根值由原2143N降低至175N。同时簧载质量加速度均方根值
由原3.5108m/s
2
降低至1.2682m/s
2
。台架测试证明齿圈应力在采用滤振缓冲措施后得到较大衰减
最大值由519.9MPa降低为110.1MPa。通过仿真和试验
验证了滤振与缓冲的措施能够提升机电悬架的性能
有助于解决惯性质量带来的高频区性能恶化的问题。
In order to solve the problem of performance deterioration and ensure structural reliability of the electromechanical suspension of high-speed tracked vehicles in high-frequency zone
the stiffness characteristics of the electromechanical suspension based on the torsion bar are analyzed
the complex motion relationship of the suspension rod system is solved
the equivalent inertia mass of the electric actuator is calculated
and a two-degree-of-freedom electromechanical suspension model considering inertia mass and load wheel damping is established. We quantitatively analyze the adverse impact of inertia mass on suspension performance
and obtain the frequency domain distribution interval and power spectral density distribution interval of inertia force affecting suspension's ride comfort and component reliability. According to the frequency domain distribution of suspens
ion inertia force and the amplitude frequency characteristics of the suspension's dynamic deflection
the measures of vibration filtering and buffering are put forward
and a suspension model with the vibration filtering buffer is established. The simulation and test results show that vibration filtering and buffering can effectively reduce the influence of inertial mass. Under the driving condition of 40km/h on class D Road
the root mean square value of the original inertial force is reduced from 2143N to 175N
and the root mean square value of sprung mass acceleration is reduced from 3.5108m/s
2
to 1.2682m/s
2
. The bench test shows that the gear ring stress is greatly attenuated after the vibration filtering and buffering measures are adopted
and the maximum value is reduced from 519.9MPa to 110.1MPa. Through simulation and test
it is verified that the measures of vibration filtering and buffering can improve the performance of the electromechanical suspension and help to solve the problem of performance deterioration in the high frequency zone caused by inertial mass.
WEEKS D A , BRESIE D A , GUENIN A M , et al. The design of an electromagnetic linear actuator for an active suspension [C ] // Proceeding of SAE International Congress and Exposition.Detroit,MI, US:SAE , 1999 .
WEEKS D A , BENO J H , GUENINA M , et al. Electromechanical active suspension demonstration for off-road vehicles at the university of texas center for electromechanics [C ] // Proceeding of SAE International Congress and Exposition.Detroit,MI, US:SAE , 2000 .
HAYES R J , BENO J H , WEEKS D A , et al. Design and testing of an active suspension system for a 2-1/2 Ton military truck [C ] // Proceeding of SAE World Congress. Detroit,MI, US:SAE , 2005 .
BYLSMA W , GUENIN A M , BENO J H , et al. Electromechanical suspension performance testings [C ] // Proceeding of SAE World Congress. Detroit,MI,US:SAE , 2001 .
毛明 , 张亚峰 , 杜甫 , 等 . 高机动履带车辆行驶系统中的5个科学技术问题 [J ] . 兵工学报 , 2015 , 36 ( 8 ): 1546 - 1555 . DOI: 10.3969/j.issn.1000-1093.2015.08.024 http://doi.org/10.3969/j.issn.1000-1093.2015.08.024 行驶系统对坦克装甲车辆的性能尤其是机动性有特别重要的影响,然而由于工作环境复杂且恶劣,使行驶系统技术成为制约坦克装甲车辆性能提高的“瓶颈”。论述了高机动履带车辆行驶系统中基于机电相似系统的振动衰减网络设计、复杂系统非线性振动动力学、能量耗散、地面力学和非线性振动控制等5个科学技术问题的概念内涵、研究目标、研究内容和前人的研究成果,期望引起各方面的关注,并深入开展基础理论层面上的研究和工程技术层面上的协同攻关。行驶系统对坦克装甲车辆的性能尤其是机动性有特别重要的影响,然而由于工作环境复杂且恶劣,使行驶系统技术成为制约坦克装甲车辆性能提高的“瓶颈”。论述了高机动履带车辆行驶系统中基于机电相似系统的振动衰减网络设计、复杂系统非线性振动动力学、能量耗散、地面力学和非线性振动控制等5个科学技术问题的概念内涵、研究目标、研究内容和前人的研究成果,期望引起各方面的关注,并深入开展基础理论层面上的研究和工程技术层面上的协同攻关。
MAO M , ZHANG Y F , DU F , et al. Five scientific and technological problems on running system of High mobility tracked vehicle [J ] . Acta Armamentarii , 2015 , 36 ( 8 ): 1546 - 1555 . (in Chinese) DOI: 10.3969/j.issn.1000-1093.2015.08.024 http://doi.org/10.3969/j.issn.1000-1093.2015.08.024 The running system is very important for tank and armored vehicles, especially for the mobility performance. The running system becomes a bottleneck to improve the performance of tank and armored vehicles due to the complex and adverse working environment. The concept, connotation, research objectives, research contents and research achievements of five scientific and technological problems, such as vibration damping network design based on the electrical and mechanical analogy, nonlinear vibration dynamics of complex system, energy dissipation, ground mechanics and nonlinear vibration control, are discussed. The fundamental theoretical research is carried out, and the key technical problems are overcome by collaborative research.
HAMID T . A novel energy harvesting approach for hybrid electromagnetic-based suspension system of off-road vehicles considering terrain deformability [J ] . Mechanical Systems and Signal Processing , 2021 , 146 ( 1 ): 106988 - 107006 . DOI: 10.1016/j.ymssp.2020.106988 http://doi.org/10.1016/j.ymssp.2020.106988 https://linkinghub.elsevier.com/retrieve/pii/S0888327020303745 https://linkinghub.elsevier.com/retrieve/pii/S0888327020303745
寇发荣 , 陈晨 , 李阳康 , 等 . 电磁复合式馈能悬架半主动控制研究 [J ] . 中国科技论文 , 2020 , 15 ( 2 ): 167 - 173 .
KOU F R , CHEN C , LI Y K , et al. Research on semi-active control of electromagnetic hybrid energy-fed suspension [J ] . China Science Paper , 2020 , 15 ( 2 ): 167 - 173 . (in Chinese)
ZHAO Z H , GUAN Y L , CHEN S A . Experimental research on PMSM ball screw actuator and structural design suggestion of featured active suspension [J ] . IEEE Access , 2020 , 99 ( 8 ): 66163 - 66177 .
喻凡 , 张勇超 . 馈能型车辆主动悬架技术 [J ] . 农业机械学报 , 2010 , 41 ( 1 ): 1 - 6 .
YU F , ZHANG Y C . Technology of regenerative vehicle active suspensions [J ] . Transactions of the Chinese Society for Agricultural Machinery , 2010 , 41 ( 1 ): 1 - 6 . (in Chinese)
黄昆 , 喻凡 , 张勇超 . 基于能量流动分析的电磁式馈能型主动悬架控制 [J ] . 上海交通大学学报 , 2011 , 45 ( 7 ): 1068 - 1073 .
HUANG K , YU F , ZHANG Y C . Active control of energy-regenerative electromagnetic suspension based on energy flow analysis [J ] . Journal of Shanghai Jiao Tong University , 2011 , 45 ( 7 ): 1068 - 1073 . (in Chinese)
殷珺 , 罗建南 , 喻凡 . 汽车电磁式主动悬架技术综述 [J ] . 机械设计与研究 , 2020 , 36 ( 1 ): 161 - 168 .
YIN J , LUO J N , YU F . The-state-of-art review on automotive electromagnetic active suspension technolog [J ] . Machine Design and Research , 2020 , 36 ( 1 ): 161 - 168 . (in Chinese)
曹民 , 刘为 , 喻凡 . 车辆主动悬架用电机作动器的研制 [J ] . 机械工程学报 , 2008 , 44 ( 11 ): 224 - 228 . 针对现有车用液力式主动悬架作动器普遍存在的响应慢、能耗大、蓄能效率低和结构复杂等不足,提出采用滚珠螺旋传动式无刷电机作动器的电机蓄能式主动悬架,并对该主动悬架的结构原理和电机作动器的创新设计方案。并以某中级轿车半独立后悬架作为试验对象,对电动机作动器的弹性元件、滚珠丝杠和无刷电动机等重要部件进行结构设计以及对输出特性进行分析推导。试制出电机作动器的功能样机,并对电气特性和被动响应特性进行测试分析,初步验证了该电机作动器的可行性和有效性,同时还阐述在有待进一步改进的设计缺陷,以及尚须进一步测试的主动控制响应和电磁蓄能特性等性能指标。
CAO M , LIU W , YU F . Development on electromotor actuator for active suspension of vehicle [J ] . Chinese Journal of Mechanical Engineering , 2008 , 44 ( 11 ): 224 - 228 . (in Chinese)
张进秋 , 彭志召 , 岳杰 , 等 . 车辆馈能悬挂技术综述 [J ] . 装甲兵工程学院学报 , 2012 , 26 ( 5 ): 1 - 7 .
ZHANG J Q , PENG Z Z , YUE J , et al. Review of regenerative suspension technology for vehicle [J ] . Journal of Academy of Armored Force Engineering , 2012 , 26 ( 5 ): 1 - 7 . (in Chinese)
张进秋 , 王兴野 , 贾进峰 , 等 . 主动悬架有限频域H∞时滞控制参数影响分析及优化 [J ] . 兵工学报 , 2018 , 39 ( 9 ): 1850 - 1857 . DOI: 10.3969/j.issn.1000-1093.2018.09.023 http://doi.org/10.3969/j.issn.1000-1093.2018.09.023 基于线性矩阵不等式的方法,设计了考虑控制输入时滞的有限频域H<sub>∞</sub>控制算法。在该算法设计中,以提高车辆乘坐舒适性、降低车体加速度为控制目标,以悬架动行程小于最大许用行程、车轮与地面始终保持良好接触、作动器出力小于其最大出力为控制的3个约束条件,分析了控制参数对求解结果的影响。针对控制参数经验取值难以得到控制的最优解,且不同时滞条件下参数取值不具有通用性的问题,提出了基于遗传算法的优化设计方法,并对求解得到的控制算法性能进行了仿真分析。结果表明:基于遗传算法优化设计并考虑了控制时滞的有限频域H<sub>∞</sub>控制算法,能够有效地降低时滞对控制的影响,提高车辆在4~8 Hz频域范围内的乘坐舒适性,且控制效果明显优于依靠经验设计的控制算法和未考虑控制输入时滞的控制算法。
ZHANG J Q , WANG X Y , JIA J F , et al. Parameter analysis and optimization of finite frequency H ∞ control with time delay for active suspension [J ] . Acta Armamentarii , 2018 , 39 ( 9 ): 1850 - 1857 . (in Chinese)
王兴野 , 张进秋 , 刘义乐 , 等 . 作动器惯性质量对主动悬架幅频特性的影响 [J ] . 汽车工程 , 2018 , 40 ( 9 ): 1083 - 1088 .
WANG X Y , ZHANG J Q , LIU Y L , et al. Influence of inertia mass in actuator on amplitude-frequency characteristics of active suspension [J ] . Automotive Engineering , 2018 , 40 ( 9 ): 1083 - 1088 . (in Chinese)
彭虎 , 张进秋 , 张建 , 等 . 并联复合式电磁悬挂模型参考多模式切换控制研究 [J ] . 兵工学报 , 2019 , 40 ( 1 ): 19 - 28 . DOI: 10.3969/j.issn.1000-1093.2019.01.003 http://doi.org/10.3969/j.issn.1000-1093.2019.01.003 传统馈能悬挂难以平衡减振和馈能之间的矛盾关系,针对该问题提出由电磁作动器和磁流变减振器组成的并联复合式电磁悬挂结构方案。为提高并联复合式电磁悬挂对不同路况的适应能力,考虑其具备不同工作模式的特点,设计了模型参考多模式切换控制器,并以提高乘坐舒适性为目标确定了切换指标、阈值及相应的控制参数。针对切换指令的离散特性和悬挂系统状态变化的连续特性,基于Stateflow软件设计了多模式切换控制系统,并确定了相应的切换规则和切换流程。对模型参考多模式切换控制器的性能进行了仿真和试验验证。结果表明:该模型参考多模式切换控制器可有效地实现并联复合式电磁悬挂各工作模式之间的切换,提高了并联复合式电磁悬挂对不同路况和驾驶需求的适应性,有效平衡了减振及馈能之间的矛盾关系。
PENG H , ZHANG J Q , ZHANG J , et al. Research on model reference multi-mode switching control of parallel composite electromagnetic suspension [J ] . Acta Armamentarii , 2019 , 40 ( 1 ): 19 - 28 . (in Chinese) DOI: 10.3969/j.issn.1000-1093.2019.01.003 http://doi.org/10.3969/j.issn.1000-1093.2019.01.003 In order to solve the problem that the traditional energy-regenerative suspension is difficult to balance the contradiction between the vibration reduction and energy-regeneration, a parallel composite electromagnetic suspension structure consisting of electromagnetic actuator and magneto-rheological damper is proposed. A model reference multi-mode switch controller is designed to improve the adaptability of parallel composite electromagnetic suspension to different road conditions, in which the characteristics of different working modes are considered, and the switching index, threshold value and corresponding control parameters are determined for the purpose of improving ride comfort. A multi-mode switching control system is designed based on Stateflow for the discrete character of switching instruction and the continuous character of state change of suspension system. The performance of model reference multi-mode switch controller are simulated and tested. The results show that the model reference multi-mode switch controller can be used to effectively implement the switching between working modes of parallel composite electromagnetic suspension, which improves its adaptability to different road conditions, and effectively balances the contradiction between vibration reduction and energy-regeneration. Key
汪若尘 , 谢健 , 叶青 , 等 . 直线电机式主动悬架建模与试验研究 [J ] . 汽车工程 , 2016 , 38 ( 4 ): 495 - 499 .
WANG R C , XIE J , YE Q , et al. Modeling and experimental study of active suspension with linear motor [J ] . Automotive Engineering , 2016 , 38 ( 4 ): 495 - 499 . (in Chinese)
汪若尘 , 钱禹辰 , 丁仁凯 , 等 . 基于LQG的混合电磁悬架阻尼-刚度设计及试验研究 [J ] . 振动与冲击 , 2018 , 37 ( 3 ): 61 - 65 .
WANG R C , QIAN Y C , DING R K , et al. Design and tests for damping-stiffness of a hybrid electromagnetic suspension based on LQG [J ] . Journal of Vibration and Shock , 2018 , 37 ( 3 ): 61 - 65 . (in Chinese)
王庆年 , 刘松山 , 王伟华 , 等 . 滚珠丝杠式馈能型减振器的结构设计及参数匹配 [J ] . 吉林大学学报(工学版) , 2012 , 42 ( 5 ): 1100 - 1106 .
WANG Q N , LIU S S , WANG W H , et al. Structure design and parameter matching of ball-screw regenerative damper [J ] . Journal of Jilin University:Engineering and Technology Edition , 2012 , 42 ( 5 ): 1100 - 1106 . (in Chinese)
段国柱 , 宋慧新 , 陈宇 , 等 . 基于MATLAB 软件的机电悬挂连杆机构的运动学分析 [J ] . 机械工程师 , 2020 ( 2 ): 103 - 104 ,109.
DUAN G Z , SONG H X , CHEN Y , et al. Kinematics analysis of mechatronic suspension linkages based on MATLAB software [J ] . Mechanical Engineer , 2020 ( 2 ): 103 - 104 ,109. (in Chinese)
余志生 , 夏群生 . 汽车理论 [M ] . 北京 : 机械工业出版社 , 2019 .
YU Z S , XIA Q S . Automobile theory [M ] . Beijing : China Machine Press , 2019 . (in Chinese)
宋慧新 , 李翠芬 . 基于频率分析的半主动悬架模糊控制方法研究 [J ] . 汽车工程 , 2008 , 30 ( 6 ): 518 - 522 .
SONG H X , LI C F . Study on the fuzzy control method of semi-active suspension based on frequency analyses [J ] . Automotive Engineering , 2008 , 30 ( 6 ): 518 - 522 . (in Chinese)
LI Z J , ZUO L , LUHRS G , et al. Electromagnetic energy-harvesting shock absorbers:design,modeling,and road Tests [J ] . IEEE Transactions on Vehicular Technology , 2013 , 62 ( 3 ): 1065 - 1074 . DOI: 10.1109/TVT.2012.2229308 http://doi.org/10.1109/TVT.2012.2229308 http://ieeexplore.ieee.org/document/6399623/ http://ieeexplore.ieee.org/document/6399623/
0
Views
156
下载量
0
CNKI被引量
Publicity Resources
Related Articles
Related Author
Related Institution
京公网安备11010802024360号