基于高速成像的爆炸温度场测试方法

doi:10.3969/j.issn.1000-1093.2021.03.021

摘要/Abstract

摘要： 为实现对爆炸温度场的动态测量，针对爆炸温度场变化快、范围广、温度高、难以测量的问题，提出一种基于高速成像技术的爆炸温度场测温方法。基于辐射原理推导出高速成像系统的温度测量模型，建立高速相机图像灰度值和被爆炸温度之间的对应关系，得到可通过控制高速成像系统曝光时间和透光率2个参数控制测温范围的算法；搭建高速成像爆炸温度场测量系统，用最小二乘法对系统进行标定，标定结果显示：该建模方法在2 200~2 900 ℃区间平均误差为0.74%，在1 850~2 350 ℃区间平均误差为1.95%，能够满足爆炸温度场的测量需求。运用搭建的系统与红外测温仪分别进行375 g、750 g及1 500 g 3种药量的温压弹爆炸温度测量对比实验，实验结果表明：该系统与红外测温仪之间的温度测量值最大偏差为3.31%，实现了高响应速率及高分辨率测量。

关键词: 爆炸温度场, 高速成像, 高温测量, 高分辨率

Abstract: A temperature measuring method for explosive temperature field based on high-speed imaging technology is proposed for the fast change, wide range, high temperature and difficult measurement of explosive temperature field. Based on the principle of radiation, a temperature measuring model of high-speed imaging system is deduced. The corresponding relationship between gray value of high-speed camera image and temperature of explosion is established, the temperature measuring range can be controlled by controlling the exposure time and transmittance of the high-speed imaging system. A high-speed imaging explosive temperature field measuring system was build, and the least square method was used to calibrate the system. The calibrated results show that the average error of the proposed method is 0.74% in the temperature range of 2 200-2 900 ℃ and 1.95% in the temperature range of 1 850- 2 350 ℃, which can meet the measuring requirements of the explosive temperature field. The proposed system and the infrared thermometer were used to measure the temperatures of 375 g, 750 g and 1 500 g explosive charges in experiment. The experimental results show that the maximum deviation of temperature measurement between the system and the infrared thermometer is 3.31%, which realizes the high response rate and high resolution measurement.

Key words: explosivetemperaturefield, high-speedimaging, hightemperaturemeasurement, highresolution

中图分类号:

TJ06

许仁翰，周钇捷，狄长安. 基于高速成像的爆炸温度场测试方法[J]. 兵工学报, 2021, 42(3): 640-647.

XU Renhan， ZHOU Yijie， DI Chang'an. A Temperature Measuring Method for Explosive Temperature Field Based on High-speed Imaging Technology[J]. Acta Armamentarii, 2021, 42(3): 640-647.

参考文献

［1］张玉磊, 翟红波, 李芝绒, 等. TNT和温压炸药的爆炸火球表面温度对比试验研究[J].爆破器材, 2015，44(5):23-26.
ZHANG Y L, ZHAI H B, LI Z R, et al. Experimental research on the contrast of the fireball's surface temperature of TNT and thermobaric explosive[J]. Explosive Materials, 2015，44(5):23- 26.(in Chinese)
[2] 赵化彬, 张志杰. 爆炸瞬态温度测试中热电偶传感器实时补偿技术[J]. 火工品, 2017(1):49-53.
ZHAO H B, ZHANG Z J. The technology of thermocouple sensor real-time compensation in explosive transient temperature test[J]. Initiators and Pyrotechnics, 2017(1):49-53. (in Chinese)
[3] 赵晨阳, 冯浩, 黄晓敏, 等. 红外测温技术在爆炸场温度测试中的精度研究[J]. 红外技术, 2014, 36(8)：676-679.
ZHAO C Y, FENG H, HUANG X M, et al. Research on the precision of the infrared temperature-measuring technology in explosion fields temperature test[J]. Infrared Technology, 2014, 36(8)： 676-679. (in Chinese)
[4] LI J, CHEN H, ZHANG S, et al. On the response of coaxial surface thermocouples for transient aerodynamic heating measurements[J]. Experimental Thermal and Fluid Science, 2017, 86:141-148.
[5] BLANKENHAGEL P, WEHRSTEDT K D, MISHRA K B. Thermal radiation assessment of fireballs using infrared camera[J]. Journal of Loss Prevention in the Process Industries, 2018, 54:246-253.
[6] 唐翃翔, 于合龙, 陈桂芬. 基于比色法的温度场测量[J].长春师范大学学报, 2014，33(3):25-27.
TANG H X, YU H L, CHEN G F. Temperature field measurement based on colorimetric method[J]. Journal of Changchun Normal University, 2014，33(3):25-27. (in Chinese)
[7] 王补宣, 李天铎, 吴占松. 图象处理技术用于发光火焰温度分布测量的研究[J].工程热物理学报, 1989, 10(4):446-448.
WANG B X, LI T D, WU Z S. The study of image processing technique used for luminous-flame temperature distribution mea-surement [J].Journal of Engineering Thermophysics, 1989, 10(4): 446-448. (in Chinese)
[8] 刘庆明, 白春华. 应用比色测温仪测量燃料空气炸药爆炸过程温度响应[J].兵工学报，2009, 30(4):425-530.
LIU Q M, BAI C H. Research on the explosive temperature Response of fuel air explosive measured by colorimetric thermometer[J]. Acta Armamentarii, 2009, 30(4):425-530. (in Chinese)
[9] 徐伟勇, 余岳峰, 张银桥, 等. 采用传像光纤和数字图像处理技术检测燃烧火焰[J]. 动力工程, 1999，19(1):45-48，79.
XU W Y, YU Y F, ZHANG Y Q, et al. Optical fiber transmission and digital image processing are used to detect the flame[J]. Power Engineering, 1999,19(1):45-48，79. (in Chinese)
[10] ZHOU H C, SHENG F, HAN S D, et al. Reconstruction of temperature distribution in a 2-D absorbing-emitting system from radiant energy images[J]. JSME International Journal Series B, 2000, 43(1):104-109.
[11] ZHOU H C, HAN S D, SHENG F, et al. Visualization of three-dimensional temperature distributions in a large-scale furnace via regularized reconstruction from radiative energy images: numerical studies[J]. Journal of Quantitative Spectroscopy and Radiative Transfer, 2002, 72(4):361-383.
[12] 徐宝昌, 张丁元. 一种改进的比色测温方法研究[J]. 光电工程, 2011, 38(4):1-6.
XU B C, ZHANG D Y.An improved colorimetric temperature measurement method[J].Opto-Electronic Engineering, 2011, 38(4): 1-6. (in Chinese)
[13] KEYVAN S, ROSSOW R, ROMERO C, et al. Comparison between visible and near-IR flame spectra from natural gas-fired furnace for blackbody temperature measurements[J]. Fuel, 2004, 83(9):1175-1181.
[14] 李汉舟, 张敏贵, 潘泉, 等. 基于面阵CCD图像的温度场测量研究[J]. 仪器仪表学报, 2003, 24(6):653-656.
LI H Z, ZHANG M G, PAN Q, et al. A study of temperature measurement based on plane surface array CCD[J]. Chinese Journal of Scientific Instrument, 2003, 24(6):653-656. (in Chinese)
[15] XUE F, DONG F T. CCD temperature measurement system design based on truncated mean weighed algorithm[J]. Applied Mechanics and Materials, 2015, 738/739:746-750.