树脂结合剂超硬磨料砂轮磨削稳定性试验研究

doi:10.3969/j.issn.1000-1093.2018.07.017

摘要/Abstract

摘要： 针对树脂结合剂超硬磨具在应用方面普遍存在的磨削性能稳定性差等工程技术问题，选取不同树脂原材料、树脂置空时间、磨料层径向位置3个关键因素作为研究对象，开展了树脂金刚石砂轮平面磨削硬质合金试验。结果表明：酚醛树脂原材料对砂轮磨削性能有较大影响，普通型树脂不适于硬质合金磨削、耐热型树脂适于大切深磨削、增韧型树脂适于小切深精密磨削；树脂置空时间对砂轮磨削性能有一定影响，随着树脂置空时间延长，磨削比缓慢下降；砂轮磨料层径向位置对磨削性能影响较特殊，当磨料层在1.0 mm以上时磨削比变化不大，当磨料层在1.0 mm以下时磨削比出现明显下降。树脂超硬磨料砂轮制成工艺及磨削应用技术的细化有利于改善砂轮磨削性能的稳定。

关键词: 树脂金刚石砂轮, 硬质合金, 磨削稳定性, 磨削比

Abstract: Three key influencing factors of different resin raw materials, setting time of resin and radial position of abrasive layer are investigated for the poor stability of grinding properties of superhard resin bonding abrasives, and a resin diamond grinding wheel is used to grind a cemented carbide in test. The results show that the phenolic resin raw materials have a great influence on the grinding performance of grinding wheel, the ordinary resin is not suitable for carbide grinding, the heat-resistant resin is suitable for deep grinding, and the toughening resin is suitable for micro-depth cut grinding. The store time of phenolic resin has a certain influence on grinding performance, the grinding ratio decreases slowly with the extending of store time; and the radial position of abrasive layer has a special effect on the grinding performance. When the abrasive layer is above 1.0 mm in thickness, the grinding ratio changes little; when the abrasive layer is below 1.0 mm in thickness, the grinding ratio decreases obviously. Refining of making and grinding technologies of super-hard resin grinding wheel is beneficial to improve the stability of grinding performance. Key

Key words: resindiamondgrindingwheel, cementedcarbide, grindingstability, grindingratio

中图分类号:

TG74⁺3

冯克明，邢波，师超钰，朱建辉，赵金坠. 树脂结合剂超硬磨料砂轮磨削稳定性试验研究[J]. 兵工学报, 2018, 39(7): 1389-1396.

FENG Ke-ming, XING Bo, SHI Chao-yu, ZHU Jian-hui, ZHAO Jin-zhui. Experimental Study on Grinding Stability of Superabrasive Grinding Wheel for Resin Bond[J]. Acta Armamentarii, 2018, 39(7): 1389-1396.

参考文献

［1］王春辉, 安润莉, 史双佶, 等. W-Mo-Cr合金对金刚石砂轮磨块的摩擦化学修整[J]. 金刚石与磨料磨具工程, 2017, 37(1): 51-55.
WANG Chun-hui, AN Run-li, SHI Shuang-jie, et al. Dynamic friction dressing of the diamond abrasive brick by W-Mo-Cr alloy[J]. Diamond & Abrasives Engineering, 2017, 37(1): 51-55.(in Chinese)
[2］ Jia K,Fischer T E．Abrasion resistance of nanostructured and conventional cemented carbides[J]. Wear, 1996, 200(1/2): 206-214.
[3］张卫兵, 刘向中, 陈振华, 等．WC-Co硬质合金最新进展[J]．稀有金属, 2015, 39(2)：178-186.
ZHANG Wei-bing, LIU Xiang-zhong, CHEN Zhen-hua, et al. Latest development of WC-Co cemented carbide[J]. Chinese Journal of Rare Metals, 2015, 39(2): 178-186. (in Chinese)
[4］ Gille G, Szesny B, Dreyer K, et al. Submicron and ultrafine grained hardmetals for microdrills and metal cutting inserts[J]. International Journal of Refractory Metals & Hard Materials, 2002, 20(1)：3-22.
[5］徐涛. 硬质合金高端产品及新材料发展趋势分析[J]. 硬质合金, 2011, 28(6)：395-402.
XU Tao. Development trend analysis of advanced products and new materials of cemented carbide[J]. Cemented Carbide, 2011, 28(6): 395-402. (in Chinese)
[6］徐豫新, 王树山, 翟喆, 等. 高速钨合金破片对中厚钢靶的穿甲效应研究[J]．兵工学报, 2009, 30(2)：259-262.
XU Yu-xin, WANG Shu-shan, ZHAI Zhe, et al. Research on armour-piercing effect of high velocity tungsten alloy fragment against medium-thick steel target[J]. Acta Armamentarii, 2009, 30(2): 259-262. (in Chinese)
[7］ Liu K, Li X P. Ductile cutting of tungsten carbide[J]. Journal of Materials Processing Technology, 2001, 113(1/2/3): 348-354.
[8］任玉刚, 邓乾发, 叶程, 等. 磨具用树脂结合剂的研究现状与展望[J]. 机械工程材料, 2012, 36(5)： 1-4,9.
REN Yu-gang, DENG Qian-fa, YE Cheng, et al. Prospect and research progress of resin binder used for abrasive tools[J]. Materials for Mechanical Engineering, 2012, 36(5): 1-4,9. (in Chinese)
[9］周金龙. 机床行业的发展对磨料磨具产品的需求变化—CIMT2015展会述评[J]．世界制造技术与装备市场, 2015(5)：64-65.
ZHOU Jin-long. Development of machine tool industry: demand for abrasives and abrasive tools—review of CIMT 2015 Exhibition [J].World Manufacturing Engineering & Market, 2015(5)： 64-65. (in Chinese)

[10］陈雷, 曾黎明, 叶晓川, 等. 偶联剂处理对金刚石树脂砂轮磨削性能的影响[J]. 金刚石与磨料磨具工程, 2010, 30(4): 54-57.
CHEN Lei, ZENG Li-ming, YE Xiao-chuan, et al. Influences of silane coupling agent on the grinding performances of resin bond diamond wheels[J]. Diamond & Abrasives Engineering, 2010, 30(4): 54-57. (in Chinese)
[11］叶晓川, 曾黎明, 陈雷, 等. 金刚石改性处理对不同树脂砂轮磨削性能的影响[J]. 金刚石与磨料磨具工程, 2010, 30(5): 65-68.
YE Xiao-chuan, ZENG Li-ming, CHEN Lei, et al. Effect of modification treatment of diamond abrasive on grinding perfor- mances of different resin bonded wheels[J]. Diamond & Abrasives Engineering, 2010, 30(5): 65-68. (in Chinese)
[12］ Singh A, Yadav R K, Srivastava A. Synthesis of resole-type phenolic beads from phenol and formaldehyde by suspension polymerization technique[J]. Journal of Applied Polymer Science, 2009, 112(2): 1005-1011.
[13］ Reghunadhan N. Advances in addition-cure phenolic resins[J]. Progress in Polymer Science, 2004, 29(5): 1401-1409.
[14］冯利邦, 李晖, 郝相忠, 等. 磷酸改性酚醛树脂的结构与耐热性能[J]. 材料工程, 2013(9): 75-78.
FENG Li-bang, LI Hui, HAO Xiang-zhong, et al.Structure and thermal resistance of phosphoric acid-modified phenol-formaldehyde resin[J]. Journal of Materials Engineering, 2013(9): 75-78. (in Chinese)
[15］蒋海云, 杭祖圣, 王继刚, 等. 酚醛树脂的热改性方法及研究进展[J]. 材料工程, 2011(10): 91-96.
JIANG Hai-yun, HANG Zu-sheng, WANG Ji-gang, et al.Thermal modifying methods and progress of phenol-formaldehyde resin[J]. Journal of Materials Engineering, 2011(10): 91-96. (in Chinese)
[16］高翀, 朱峰, 刘明耀, 等. 酚醛树脂改性及在超硬磨具中的应用研究现状[J]. 金刚石与磨料磨具工程, 2014, 34(1): 64-69.
GAO Chong, ZHU Feng, LIU Ming-yao, et al. Research state on phenolic resin modification and application in superabrasive grinding tools[J]. Diamond & Abrasives Engineering, 2014, 34(1): 64-69. (in Chinese)
[17］柳文阳, 谢宏, 张亚雄, 等. 不同结合剂金刚石砂轮在硬质合金刀片磨削中的性能对比[J]. 硬质合金, 2016, 33(1): 38-41.
LIU Wen-yang, XIE Hong, ZHANG Ya-xiong, et al. Perfor- mance comparison of diamond wheels with different bond in grinding cemented carbide blade[J]. Cemented Carbide, 2016, 33(1): 38-41. (in Chinese)
[18］熊华军, 李克华, 叶腾飞, 等. 树脂金刚石砂轮内圆磨削硬质合金工件的试验研究[J]. 超硬材料工程, 2016, 28(5): 1-5.
XIONG Hua-jun, LI Ke-hua, YE Teng-fei, et al.Experimental study of the internal grinding of cemented carbide workpiece by resin bond diamond grinding wheel[J]. Superhard Material Engineering, 2016, 28(5): 1-5. (in Chinese)
[19］ Deng Q F, Yuan J L, Wang Z Z, et al. An investigation to semi-fixed abrasives plate characteristics[J]. Key Engineering Materials, 2009, 416: 563-567.
[20］胡超, 李长虹, 赵先锋, 等. 硬质合金磨削温度场的仿真与试验研究[J]. 工具技术, 2017, 51(5): 22-25.
HU Chao, LI Chang-hong, ZHAO Xian-feng, et al. Simulation and experimental study of temperature for carbide grinding[J]. Tool Engineering, 2017, 51(5): 22-25. (in Chinese)
[21］张东生, 林静, 张力允, 等. 硬质合金平面磨削温度场仿真研究[J]. 机械工程师, 2015(11): 160-163.
ZHANG Dong-sheng, LIN Jing, ZHANG Li-yun, et al. Simulation and research of carbide plane grinding temperature field[J]. Mechanical Engineer, 2015(11): 160-163. (in Chinese)
[22］任莹晖, 张璧, 周志雄, 等. 纳米结构硬质合金磨削的表面形貌和材料去除机理研究[J]. 中国机械工程, 2009, 20(8): 896-901.
REN Ying-hui, ZHANG Bi, ZHOU Zhi-xiong, et al. Surface morphology and material-removal mechanism in grinding of nanostructured tungsten carbide[J]. China Mechanical Engineering, 2009, 20(8): 896-901. (in Chinese)
[23］杨军, 黄向明, 蒋福星, 等. 纳米硬质合金高速深磨工艺试验研究[J]. 现代制造工程, 2015(10): 12-17.
YANG Jun, HUANG Xiang-ming, JIANG Fu-xing, et al. Experimental investigation on high speed deep grinding characteristics of the nano-cemented carbides[J]. Modern Manufacturing Engineering, 2015(10): 12-17. (in Chinese)
[24］程敏, 余剑武, 谢桂芝, 等. 硬质合金YG8高速磨削工艺试验研究[J]. 制造技术与机床, 2011(1): 25-29.
CHENG Min, YU Jian-wu, XIE Gui-zhi, et al. Experimental investigation on high speed grinding characteristics of the cemented carbides-YG8[J]. Manufacturing Technology & Machine Tool, 2011(1): 25-29. (in Chinese)
[25］徐翠平, 徐三魁, 彭进, 等. 超硬磨具用耐高温酚醛树脂结合剂的合成与表征[J]. 金刚石与磨料磨具工程, 2012, 32(3): 74-77.
XU Cui-ping, XU San-kui, PENG Jin, et al. Synthesis and characterization of high temperature resistant phenolic resin binder for superhard abrasive tools[J]. Diamond & Abrasives Engineering, 2012, 32(3): 74-77. (in Chinese)
[26］华勇, 李亚萍, 蒋登高, 金刚石砂轮树脂结合剂的性能分析[J], 金刚石与磨料磨具工程, 2004, 143(5): 4-6.
HUA Yong, LI Ya-ping, JIANG Deng-gao. Analysis on the performances of resinoid bond used in diamond grinding wheel[J]. Diamond & Abrasives Engineering, 2004, 143(5): 4-6. (in Chinese)
[27］陈振华. 粉末压缩的流变学问题(一)——粉末体的流变特性[J]. 稀有金属材料与工程, 1992, 21(1): 3-7.
CHEN Zhen-hua. Rheology on powder compaction (1)—rheological behavior of powder during the compression process[J]. Rare Metal Materials and Engineering, 1992, 21(1): 3-7. (in Chinese)
[28］谷曼, 焦明华, 孙龙, 等. 粉末压制过程中的摩擦行为研究[J]. 热加工工艺, 2014, 43(9): 109-112.
GU Man, JIAO Ming-hua, SUN Long, et al.Research on friction behavior in powder compaction process[J]. Hot Working Technology, 2014, 43(9): 109-112. (in Chinese)

第39卷第7期2018 年7月兵工学报ACTA
ARMAMENTARIIVol.39No.7Jul. 2018