点火增长反应速率方程在LS-DYNA软件中嵌入及应用

doi:10.3969/j.issn.1000-1093.2019.07.010

兵工学报 ›› 2019, Vol. 40 ›› Issue (7): 1411-1417.doi: 10.3969/j.issn.1000-1093.2019.07.010

点火增长反应速率方程在LS-DYNA软件中嵌入及应用

苗飞超¹，周霖¹，张向荣¹，曹同堂²

(1.北京理工大学爆炸科学与技术国家重点实验室, 北京 100081; 2.安徽东风机电科技股份有限公司, 安徽合肥 230000)

收稿日期:2018-09-28 修回日期:2018-09-28 上线日期:2019-09-03
作者简介:苗飞超(1994—)，男，博士研究生。E-mail:miaofeichao@bit.edu.cn
基金资助:
国家自然科学基金项目(11772060)

Implantation and Application of Ignition and Growth Reaction Rate Equation in LS-DYNA Software

MIAO Feichao¹， ZHOU Lin¹， ZHANG Xiangrong¹， CAO Tongtang²

(1.State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081，China;2.Anhui Dongfeng Mechanical and Electrical Technology Co., Ltd., Hefei 230000, Anhui, China)

Received:2018-09-28 Revised:2018-09-28 Online:2019-09-03

摘要/Abstract

摘要： 为了得到能够正确描述炸药的冲击起爆过程且易于标定的反应速率方程，将一种点火增长反应速率方程嵌入LS-DYNA软件，并模拟DNAN基熔注炸药的冲击起爆过程。通过对比计算压力曲线和实验压力曲线标定这种点火增长反应速率方程参数，进一步分析在LS-DYNA软件中嵌入点火增长反应速率方程的优点。结果表明：这种点火增长反应速率方程参数较少、易于标定；计算得到的4个传感器位置处冲击波到达时间与实验值相差不超过0.2 μs，该反应速率方程能够正确描述炸药的冲击起爆过程；反应速率方程嵌入LS-DYNA软件所采用的算法效率高，计算中每个网格的迭代次数不超过3次。

关键词: 熔注炸药, 冲击起爆, 点火增长模型, 反应速率方程, 状态方程

Abstract: An ignition and growth reaction rate equation with 10 parameters is implanted into LS-DYNA software to precisely describe the shock initiation of explosives and simplify the calibration of reaction rate equation. The reaction rate equation is used to simulate the shock initiation of a DNAN-based melt-cast explosive. The parameters of the reaction rate equation are calibrated by comparing the pressure-time curves in experiment and simulation, and the advantages of the reaction rate equation are analyzed. The results indicate that the reaction rate equation can be easily calibrated due to a few number of parameters. The difference between the simulated and experimental arrival times of shock wave does not exceed 0.2 μs, and thus the reaction rate equation can be used to precisely describe the shock initiation of explosives. The algorithm for implanting the reaction rate equation in LS-DYNA software is efficient because the iterations for every grid does not exceed 3 times.Key

Key words: melt-castexplosive, shockinitiation, ignitionandgrowthmodel, reactionrateequation, equationofstate

中图分类号:

O381

苗飞超，周霖，张向荣，曹同堂. 点火增长反应速率方程在LS-DYNA软件中嵌入及应用[J]. 兵工学报, 2019, 40(7): 1411-1417.

MIAO Feichao， ZHOU Lin， ZHANG Xiangrong， CAO Tongtang. Implantation and Application of Ignition and Growth Reaction Rate Equation in LS-DYNA Software[J]. Acta Armamentarii, 2019, 40(7): 1411-1417.

参考文献

［1］ LEE E L, TARVER C M. Phenomenological model of shock initiation in heterogeneous explosives[J]. Physics of Fluids, 1980, 23(12): 2362-2372.
[2］ TARVER C M, HALLQUIST J O, ERICKSON L M. Modeling short pulse duration shock initiation of solid explosives[C]∥Proceedings of the 8th Symposium (International) on Detonation. Albuquerque, NM, US: Office of Naval Research, 1985: 951- 961.
[3］ LI X, SUN Y, ZHAO H, et al. A systematic method to determine and test the ignition and growth reactive flow model parameters of a newly designed polymer-bonded explosive[J]. Propellants, Explosives, Pyrotechnics, 2018, 43(9): 948-954
[4］皮铮迪, 陈朗, 刘丹阳, 等. CL-20基混合炸药的冲击起爆特征[J]. 爆炸与冲击, 2017, 37(6): 915-923.
PI Z D, CHEN L, LIU D Y, et al. Shock initiation of CL-20 based explosives[J]. Explosion and Shock Waves, 2017, 37(6): 915-923.(in Chinese)
[5］谭凯元, 文尚刚, 韩勇.常温附近温度变化对炸药冲击起爆特征的影响[J].含能材料,2016,24(9):905-910.
TAN K Y, WEN S G, HAN Y. Shock initiation characteristics of explosives at near-ambient temperatures[J]. Chinese Journal of Energetic Materials, 2016, 24(9):905-910.(in Chinese)
[6］ HUSSAIN T, LIU Y, HUANG F, et al. Ignition and growth modeling of shock initiation of different particle size formulations of PBXC03 explosive[J]. Journal of Energetic Materials, 2015,34(1): 38-48.
[7］ VANDERSALL K S, GARCIA F, TARVER C M. Shock initiation experiments with ignition and growth modeling on low density compositionB[C]∥the Conference of the American Physical Society Topical Group on Shock Compression of Condensed Matter. Tampa Bay, FL, US: American Physical Society, 2017.
[8］ LI Y, YANG X, WEN Y, et al. Determination of Lee-Tarver model parameters of JO-11C explosive[J]. Propellants, Explosives, Pyrotechnics， 2018, 43(10):1032-1040.
[9］ MURPHY M. An improved reaction rate equation for simulating the ignition and growth of reaction in high explosives[C]∥Proceedings of the 14th Symposium (International) on Detonation. Coeur d'Alene, ID, US: Office of Naval Research, 2010: 1491-1497.

[10］ COCHRAN S G, CHAN J. Shock initiation and detonation mo- dels in one and two dimensions: UCID-18024[R]. Livermore, CA, US: Lawrence Livermore National Laboratory, 1979.
[11］ CAO T, ZHOU L, ZHANG X, et al. Shock initiation characteristics of an aluminized DNAN/RDX melt-cast explosive[J]. Journal of Energetic Materials, 2017, 35(4): 430-442.
[12］温丽晶. PBX炸药冲击起爆细观反应速率模型研究[D]. 北京:北京理工大学, 2011.
WEN L J. Research on mesoscopic reaction rate model of shock initiation of PBX[D]. Beijing:Beijing Institute of Technology, 2011.(in Chinese)

第40卷
第7期2019 年7月兵工学报ACTA
ARMAMENTARIIVol.40No.7Jul.2019

[1]	李淑睿，段卓平，白志玲，张旭，黄风雷. 2，4-二硝基苯甲醚基熔铸含铝炸药冲击起爆特性[J]. 兵工学报, 2022, 43(6): 1288-1294.
[2]	李淑睿，段卓平，郑保辉，罗观，黄风雷. 24-二硝基苯甲醚基熔铸含铝炸药圆筒试验及爆轰产物状态方程[J]. 兵工学报, 2021, 42(7): 1424-1430.
[3]	贺翔，严楠，曾祥涛，解瑞珍，鲍丙亮，张良，吴伟明. 微尺寸叠氮化铅驱动飞片重要结构参数与飞片速度和能量的关系[J]. 兵工学报, 2021, 42(7): 1363-1371.
[4]	姚成宝，付梅艳，韩峰，闫凯，雷雨. 基于多介质Riemann问题的流体-固体耦合数值方法及其在爆炸与冲击问题中的应用[J]. 兵工学报, 2021, 42(2): 340-355.
[5]	李东伟，苗飞超，张向荣，熊国松，周霖，赵双双. 2，4-二硝基苯甲醚基不敏感熔注炸药动态力学性能[J]. 兵工学报, 2021, 42(11): 2344-2349.
[6]	白志玲，段卓平，黄风雷. 高聚物粘结炸药冲击起爆统计热点反应速率模型[J]. 兵工学报, 2021, 42(11): 2379-2387.
[7]	赵聘，陈朗，李金河，鲁建英，伍俊英. 聚能射流侵彻隔板形成的前驱冲击波起爆不同温度炸药特性[J]. 兵工学报, 2021, 42(1): 45-55.
[8]	李科斌，董新龙，李晓杰，闫鸿浩，王小红. 水下爆炸实验法在工业炸药JWL状态方程测定中的应用研究[J]. 兵工学报, 2020, 41(3): 488-494.
[9]	刘荣强，聂建新，焦清介，徐新春. JO-9C小尺寸传爆药驱动飞片影响因素模拟仿真研究[J]. 兵工学报, 2020, 41(2): 246-253.
[10]	赵星宇，白春华，姚箭，孙彬峰. 燃料空气炸药爆轰产物JWL状态方程参数计算[J]. 兵工学报, 2020, 41(10): 1921-1929.
[11]	李瑞, 李伟兵, 靳洪忠, 王桂林, 洪晓文, 朱建军, 李文彬, 王晓鸣. 基于Jones-Wilkins-Lee状态方程的爆轰波相互作用参数理论分析[J]. 兵工学报, 2019, 40(3): 516-521.
[12]	谭凯元，韩勇，曹落霞，文尚刚，王翔，叶辉. 装药密度小幅变化对三氨基三硝基苯基聚合物粘结炸药短脉冲冲击起爆特性的影响[J]. 兵工学报, 2018, 39(3): 468-473.
[13]	陈闯，郝永平，杨丽，王晓鸣，李文彬，李伟兵. 双层介质隔板试验及被发炸药冲击起爆特性分析[J]. 兵工学报, 2017, 38(10): 1957-1964.
[14]	黄闯，党建军，李代金，罗凯. 跨声速运动对射弹阻力及空化特性的影响[J]. 兵工学报, 2016, 37(8): 1482-1488.
[15]	白志玲，段卓平，景莉，刘益儒，欧卓成，黄风雷. 飞片冲击起爆高能钝感高聚物粘结炸药的实验研究[J]. 兵工学报, 2016, 37(8): 1464-1468.

点火增长反应速率方程在LS-DYNA软件中嵌入及应用

Implantation and Application of Ignition and Growth Reaction Rate Equation in LS-DYNA Software

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价